Reviews
Used to secure Plate to repainted Frame
I bought a battered 900SS (900SL) and am Restore.
For the frames with noticeable rust, I had originally planned to remove the rust by rubbing the paint off with a wire brush, and then finish with a two-component urethane can spray from DAYTONA, Soft99, or Okitsumo.
However, when I rubbed the slightly rusted area...I found that the rust was progressing like a worm crawling under the paint film.
We had no choice but to strip off all the paint, but then the problem would be the MODELPlate that is Rivet-fastened to the frame.
It is clear that the display printed on the Plate would also peel off if the Plate is left as it is, so the Plate was removed before the paint was peeled off.
After stripping the paint, removing the rust with sandblast, and powder coating (we gave up on the two-component urethane can spray finish because the rust in the intricate areas was too severe to remove with a wire brush), the Plate must now be mounted on the Frame. I gave up on the two-component Urethane can Spray finish.
This Rivet was used in that case.
There is no particular element that says, "This is the only Rivet! It is a very ordinary Rivet.
Aluminum Flange、Stainless shaft。
I could have purchased it separately at Home center, but it would have been a hassle to go and buy it, and I bought Rivet along with my other purchases.
There is no absolute necessity to buy at Webig, but it is convenient to be able to buy small items such as these all at once.
These ultra-fine Size Rivets are I went to the home center and it wasn't there. What a frequent occurrence....
It may be a little cheaper if you buy from a specialty store like Monota0u, but if you consider the shipping cost and the hassle of having it delivered by RoseRose, it is more economical to buy from WeBig for a small price difference.
And there's no way I'd buy just this one.
The feeling of using the Rivet is very normal, so there is nothing special to say.
If I may say so, it is better to prepare a bag with a zipper if you do not plan to use it up, because it is not designed to be stored when the Package is opened (it is just a Blister pack).
View detail
Well made.
Purchased to disassemble and clean Exhaust System.
The product is solid and durable.
The size of the Rivet can also be covered with the size that would normally be used.
Size can be changed by replacing Adapter.
Crimping the Rivet takes a lot of force.
Crimp firmly without fear of injury.
It's not a tool you'll use over and over again, but it's the kind of tool you can find at a hardware store.
Unlike cheaper products, this product is well made, so if you look at it in the long run, you will find that this product is better than the cheaper ones.
I think it's good
View detail
Convenient to have
I bought this to install fogs on my Motorcycle.
Pipe is drilled and the nut is crimped with a nutter here.
Easily install fog or anything else with Bolt tightening.
I do need to drill some holes with a Drill.
Once processed with a nutter, the parts can be installed and removed with Bolt On.
There is a difference in finish between with and without.
It's a solid product, and it's a good product.
The work was not difficult or broken down.
I think it's a good product
View detail
To the thickness that cannot be tapped, etc
I often use a nutter for something so thick that the Tap can't cut it
Thin plates can be fixed with a bolt nut, but you can also set up a bracket on a frame or other parts The best place to do this is usually with a co-tightening on the Bolt somewhere, but it's not the best place Sometimes you really want a Screw hole
If you have one, it's a necessity because it's useful for anything and we often do diversionary parts
But even with M5, you can drill a pre-drilled hole of about Φ7, so consider the strength of the hole, depending on the location And if the hole you drilled is Steel, it's best to paint it to prevent rust
View detail
Signet Blind Rivets
Great quality rivets. Stainless Steel shaft and aluminium body. The rivet diameter is 4mm and can be used for materials upto 12mm thick. Great quality for a good price! View detail