Reviews
Used to remove the Clutch of LETS4Palette
When removing the clutch outer of the LETS4Palette, the nut holding the clutch outer in place was used to loosen it.
I was able to loosen a nut that did not loosen at all with the 150~180mmRatchet wrench I usually use.
Because of its long overall length, it is a convenient tool that can be used to apply large torques even by human power.
View detail
Axle Shaft, etc.
I bought this to replace the Wheel on my ZrX1200R.
I used it to loosen an Axle Shaft and it was easy to apply force.
Other uses would be useful, such as loosening the nut on the wheel of a car.
View detail
Easy to put effort into.
I purchased this product to install a Hepco/Becker Engine Guard.
Since the SV650 has a frame fixed by the engine, it requires a lot of torque, so we used a long handlebar.
As a result, I was able to remove it with ease.
The length is nice and fits in the e-value Tools Set.
View detail
Necessary and sufficient performance
[How is it used?
It is useful for loosening axle shafts and steering nuts on motorcycles.
It can also be used to replace Tire on cars.
Was the one you received as per Image?
It was just as Image.
I appreciate that SK11 has a pretty good selection of products with excellent Cost performance.
There are some spec. for reduction in cost, such as no holes in the handles and no Knurl processing to prevent slipping, but I think it is sufficient.
I also use a Torque wrench to hang Torque.
How was your experience with it?
It is quite effective for Bolts and Nuts that do not loosen or have high Torque applied to them.
Basically, it is used for bolt and nut of the undercarriage that is stuck, but it is easy to work with thanks to its length.
Socket tools are mainly aligned with a 3/8 insertion angle, but for those that are unlikely to come loose, 1/2Socket is prepared in advance and used.
How did it compare to other products?
The Spinner Handlebar of this length made by other well-known manufacturers is quite pricey, so it's nice to know that it's cosmetically sound.
View detail
Easy to put effort into.
I purchased this product to install a Pepco Becker Engine Guard.
Since the SV650 has a frame fixed by the engine, it requires a lot of torque, so we used a long handlebar.
As a result, we were able to remove it with ease.
The length is good.
It fits into e-value's Tools Set.
View detail
Overpriced activity
Large is convenient because it can be used in narrow and difficult-to-apply Torque.
I was concerned about the durability because of the reasonable price, but I was also able to remove the sticking Bolt.
View detail
Realizing the need for proper Tool
Maintenance tends to use compact tools, but there is a risk of damaging the bolt if you apply excessive force to loosen the bolt. It is easy to loosen the oil drain bolt. View detail
Essential Tools
I think it is safe to say that this Tool is a must-have if you are going to tinker with Motorcycle by yourself.
It is a strong ally to loosen Bolt & Nut that are sticking or in places where it is difficult to apply force with ordinary Glasses.
Combining this handlebar with a 6-sided type socket allows for loosening while reducing the risk of tampering in the case of large sizes.
Forcing yourself to work with a Tool that does not fit your purpose or situation will not do you any good.
SK11 is priced much lower than the top-rated BrandTool, but there are no problems with accuracy or strength, and it is easy to purchase.
View detail
When you need Torque.
I used a Spinner Handlebar to remove the Sidecar from the MotorcycleBody because the Bolt would not turn.
I used this Spinner Handlebar because the box wrench I usually use seems to break the wrench. 380? I was able to separate the Sidecar from the Body, and when connecting the Sidecar to the Body, I can also apply the Torque to tighten the mass.
The handlebar is heavy, responsive, and easy to use. Depending on the location, I felt that even with a sticking bolt, it would be quite possible to use this handlebar after spraying it with lubricant.
View detail
In use in Motorcycle and car
I use it not only for Motorcycle but also for my car.
The high Torque location uses a Spanner instead of a Ratchet, and the head can fold back vertically 180° so it can spin around if you grab the hang.
View detail
Safe even at high Torque
I use it to loosen axle nuts on my motorcycle and also to change tires on my car. I am satisfied that the practical strength is sufficient and I do not have to worry about it breaking. View detail
the ultimate weapon
The ultimate weapon for turning a Bolt that won't come loose.
I don't have a lot of arm strength, so I tend to use longer tools than others.
Basically, it is used for Bolt/Nut of the undercarriage that adhered, but thanks to the length, it is easy to adjust the force.
Socket tools are mainly aligned with a 3/8 insertion angle, but for those that are unlikely to come loose, 1/2Socket is prepared in advance and used.
There is no hole in the handle and there is no Knurl processing of the non-slip, and some Spec. for Reduction in cost is seen, but Platingetc. finish is also good overall.
The Spinner Handlebar of this length made by other well-known manufacturers is quite pricey, so it's nice to know that it's cosmetically sound.
View detail
Nepros 6.3sq. Long ratchet handlebar
Hello. The other day I received a parcel Nepros 6.3sq. Long Ratchet Handlebar from the Webike team for which I thank them a lot. I had long wanted to buy something from the Nepros tool. the tool is very convenient and qualitatively made, indispensable for working in a confined space due to the small angle of rotation and the narrow head of the ratchet mechanism itself, the long handle reduces the load on the hands, is very convenient in cleaning and wiped with a cloth and it is clean and shiny design is a real work of art, even it is a pity to get dirty, beautifully packaged as a piece of jewelry. On how many tools are reliable, I don’t know time will tell, but people praise they write that they are very reliable. I would like to buy something from Nepros, I really liked the tool. View detail
Since it cuts to the center portion of a handle, there is a slot and it stops at a center in simple, even if it embezzles and a slide part becomes loose, I think that it is easy-to-use. With no saying, if a price is cheap now.
Since it cuts to the center portion of a handle, there is a slot and it stops at a center in simple, even if it embezzles and a slide part becomes loose, I think that it is easy-to-use.
With no saying, if a price is cheap now.
View detail