Reviews
Tools used only occasionally are SK11
I use basic KTC and Tone for tools.
I use SK11 for tools that are used only occasionally.
Insert angle of this Deep socket:6.35mm (1/4Inch) Purchase
Sprocket Coveretc.It is necessary to remove the bolt that is deep in the bolt, and it is necessary to remove the bolt that is deep in the bolt.
Frequently used insertion angle:9.5mm (3/8Inch) Deep socket in the
If you try to use the 8mm, the Ratchet Pouch opening will be
It's thicker, so it hits the Cover.
So, insertion angle:6.35mm (1/4Inch) will be needed
But I don't use KTCetc. so I don't want to buy KTCetc. for my Wallet...
Thank goodness for SK11's Socket
Reliable quality at a reasonable price
I use KTC and Tone where I hang Large Torque.
The parts of SmallTorque that are not used much are supplemented with SK11.
View detail
Exhaust flange, etc.
It is used to remove the exhaust pipe or when the bolt nut is difficult to access due to obstructions, etc.
This is a useful item because there are times when it is not necessary to remove obstacles.
The texture is like KTC!
View detail
Not for everyone.
It is a hexagonal, low-head Profile Socket.
It is sold without any warning, but as a result of prioritizing handling, it is short and easy to use in some situations, but on the other hand, it cannot be used in places where Bolt needs a little length on the Socket side, such as a longer Penetrating Nut or Cap Nut. (Standard length sockets from other manufacturers or semi-deep sockets from ZEALBrand are required.)
Therefore, if you want to use one type of Socket for all parts of the system, it is not recommended at all.
For those who are willing to use low head whenever possible where sockets are used, and only replace them with semiDeep or other companies' products for exceptions after a bit. Beginners and Light users should buy something else. It is also not suitable for circuit use where you want to limit the number of tools you bring with you.
However, the rattling and bending when using Socket is close to Zero, so it is definitely reliable in usable areas.
View detail
3/8 might be better for the final tightening.
I would like to add that the product description was missing.
This is a Hexagon socket with a 6.35mm (1/4Inch) insertion angle. This size is 4mm.
2.I bought everything from 5 to 8mm at once.
Compact tools are easier to use for attaching/removing exterior and small objects, so they are used separately from 9.5mm (3/8) tools.
It is useful to use this Socket together with a 1/4Inch THandlebar or a 1/4 Driver-like Handlebar.
For 8mm hexes, the Torque is so large that it is safer to use a 3/8 insert depending on the location, but for hexes located in tight spaces or at the back of the room, a slim 1/4 is not acceptable.
I am using a 3/8 hex socket made by KTC, but the hex shaft (tip bit) is screw-fixed and can easily come off.
So I bought more 1/4s and made them TONE. This is good because the tip Bit is press-fitted so it won't fall out.
Can I recommend this product to my friends and acquaintances? ⇒ YES... You can RECOMMENDATION.
View detail
Compact 1/4 Inch Socket is convenient!
This is a Hexagon socket with a 6.35mm (1/4Inch) insertion angle. This size is 6mm.
2.I bought everything from 5 to 8mm at once.
Compact tools are easier to use for attaching/removing exterior and small objects, so they are used separately from 9.5mm (3/8) tools.
It is useful to use this Socket together with a 1/4Inch THandlebar or a 1/4 Driver-like Handlebar.
I am using KTC made as 3/8 Hex socket, but the Hex axis (tip Bit) is Screw fixed and can easily come off.
So I bought more 1/4s and made them TONE. This is good because the tip Bit is press-fitted so it won't fall out.
Can I recommend this product to my friends and acquaintances? ⇒ YES... You can RECOMMENDATION.
View detail
I like the way it's built with no Bit missing.
I would like to add that the product description was missing.
This is a Hexagon socket with a 6.35mm (1/4Inch) insertion angle. This size is 4mm.
2.I bought everything from 5 to 8mm at once.
Compact tools are easier to use for attaching/removing exterior and small objects, so they are used separately from 9.5mm (3/8) tools.
It is useful to use this Socket together with a 1/4Inch THandlebar or a 1/4 Driver-like Handlebar.
I am using KTC made as 3/8 Hex socket, but the Hex axis (tip Bit) is Screw fixed and can easily come off.
So I bought more 1/4s and made them TONE. This is good because the tip Bit is press-fitted so it won't fall out.
View detail
Recommended by KTC
I would like to add that the product description was missing.
Hexagon socket with a 6.35mm (1/4inch) insertion angle. 3mm in size.
This time, I bought everything from 2.5mm to 8mm.
Compact tools are easier to use for attaching/removing exterior and small objects, so they are used separately from 9.5mm (3/8) tools.
It is useful to use this Socket together with a 1/4Inch THandlebar or a 1/4 Driver-like Handlebar.
I am using KTC made as 3/8 Hex socket, but the Hex axis (tip Bit) is Screw fixed and can easily come off.
So I bought more 1/4s and made them TONE. This is good because the tip Bit is press-fitted so it won't fall out.
View detail
Recommended by KTC
I would like to add that the product description was missing.
Hexagon socket with 6.35mm (1/4inch) insertion angle and 2.5mm size.
Compact tools are easier to use for attaching/removing exterior and small objects, so they are used separately from 9.5mm (3/8) tools.
It is useful to use this Socket together with a 1/4Inch THandlebar or a 1/4 Driver-like Handlebar.
I am using KTC made as 3/8 Hex socket, but the Hex axis (tip Bit) is Screw fixed and can easily come off.
So I bought more 1/4s and made them TONE. This is good because the tip Bit is press-fitted so it won't fall out.
View detail
Made by TONE for peace of mind. Personally recommended over KTC.
I would like to add that the product description was missing.
This is a Hexagon socket with a 6.35mm (1/4Inch) insertion angle. This size is 5mm.
2.I bought everything from 5 to 8mm at once.
Compact tools are easier to use for attaching/removing exterior and small objects, so they are used separately from 9.5mm (3/8) tools.
It is useful to use this Socket together with a 1/4Inch THandlebar or a 1/4 Driver-like Handlebar.
I am using KTC made as 3/8 Hex socket, but the Hex axis (tip Bit) is Screw fixed and can easily come off.
So I bought more 1/4s and made them TONE. This is good because the tip Bit is press-fitted so it won't fall out.
Can I recommend this product to my friends and acquaintances? ⇒ YES... You can RECOMMENDATION.
View detail
Expensive! But if you don't buy this tool, you can't replace the Exhaust System!
[How is it used?
This tool is essential for removing the O2 Sensor of the Exhaust System.
I purchased this product when I exchanged it for YOSHIMURA's One piece.
Was the one you received as per Image?
Tools only, nothing else attached.
How was your experience with it?
Although I was concerned about whether Torque would really be applied, I was able to remove the Sensor without incident.
[Points to note]
CB1100's O2 Sensor is just too hard!
I was finally able to remove it while blowing CRC.
It may be tough with low-precision tools.
How did it compare to other products?
Quantity:There are inexpensive tools available as Set items, but I think this one is sufficient since it is only used for CB with only 17mmSocket.
The other tool is also available from Snap on, but is more expensive at over 10,000 yen, so we would like to have this one before it sells out.
View detail
To the Magic Remodeling Base
[How is it used?
First of all, I would like to apologize to Manufacturer,... I am sorry.
NSR250R (MC21) I purchased this product because I could not turn the cylinder nut under the RCValve of the "R" with the tools I have on hand and had to make a magic modification.
Was the one you received as per Image?
It is a Nut with a 1/4 insert diameter that is quite short in overall length as advertised.
The texture and precision of the Socket are perfect.
How was your experience with it?
If you have ever removed the Cylinder on the Rear bank side of the MC21, you know that it is in a rather troublesome position.
I visited the blog of a person who has made his own by cutting cheap Nut and put it into practice.
As you can see in the photo, I thought I had pushed and shaved it down quite a bit, but the height was still very Limit.
I tried my best to turn the nut with my Spanner, but it was a hexagonal type, so I was able to hold it firmly and remove it safely.
[Points to note]
The insert angle is 1/4, so applying too much Torque is dangerous.
How did it compare to other products?
T2Racing offers a special tool for this nut, but it is so expensive that I was hesitant to buy it.
https://www.webike.net/sd/24576874/
If you plan to work on it a number of times and want to be sure it will work, you may want to buy it.
【Review】
I think the Nut itself is very well made and accurate.
It would have been best if there was a shorter one, but this product was the most suitable for my requirements, so....
It was quite a challenge, but I am glad that I managed to turn the nut.
View detail
6.35mm (1/4Inch)
CompactRatchet, insertion angle:6.35mm (1/4Inch) This is a purchase for use in
3 different lengthsQuantity:Set, it is good because it can be used in different places of use.
6.35mm (1/4Inch) It is small, not heavy, and does not take up much space as an on-board tool, so it is likely to be quite useful.
View detail
For Bolt with Sensor
It is better to fit when turning Bolt with Sensor.
You can turn it without it, and even a homemade tool is Large sturdy, but it is easier to buy one if you can.
View detail
For servicing and maintenance use
Affordable price, so much Quantity:Set, making it convenient to use and use.
The Level is sufficient for everyday use and is fine in use.
View detail
![9.5sq. Socket Set [6 Pieces]](https://img.webike-cdn.net/catalogue/18428/ntb306a_TS.jpg)
nepros of longing
High-end tools nepros
KTC is more than enough for maintenance, but this is a hobby world.
I'd like to take care of the tools, too.
However, it is not a price you can buy with a bang.
Only frequently used Ratchet and Socket nepros
The construction looks like it took a lot of work for the price.
But it's SK11 that's easy to use.
I don't mind placing it directly on the ground or dropping it a little.
Each time nepros are used, they are gently placed on a cloth to prevent damage to the Large.
If I drop it, I could probably dent it for a day.
Well, nepros is a tool for hobbyists, including that.
View detail
conversion
I bought it to install a plug wrench on a small type ratchet. View detail
Mistook it for a hexagon and bought it.
[How is it used?
I bought this to loosen the Driven Sprocket on my XJR400R.
Was the one you received as per Image?
I did not read the product specs carefully and bought it thinking it was a hexagon, but it was a dodecagon.
It is not impossible to use a 12-square, but the way the Torque is applied changes from a 6-square to a 12-square, and it is difficult to use in places where considerable force is required.
How was your experience with it?
I still could not loosen the force well.
This caused a little damage to the Nut and I failed. This was my own fault, though, so I had no choice.
The product is inexpensive and easy to use.
[Points to note]
Read the product Spec. carefully!
It makes me sad when I buy tools I don't use lol.
How did it compare to other products?
I later purchased a similarly priced hexagonal VERSION.
I think the quality of this product is slightly higher.
View detail
Robust tool.
[How is it used?
I purchased this to remove the Oil Inspection Bolt on the lower side of the Engine on my CB1100.
Was the one you received as per Image?
It is a robust tool that does not seem to break down in the slightest.
How was your experience with it?
I was prepared to remove the bolt because it was the bolt of the engine part of a Large Motorcycle, but it came off so easily with this tool that I was surprised.
[Points to note]
If the Engine Guard or something else interferes, it is a hassle, but it is necessary to remove everything.
How did it compare to other products?
I don't know about other companies' products, but a tool with a sense of security is the best because it is a part that cannot be recovered if it is licked.
▼Although rarely used, it is a good idea to have it on hand.
View detail
For maintenance.
It was good because it was easy to use for maintenance and servicing and the types of products were well used. View detail
Used for Meter certification of CB50JX
The Tachometer lighting on my CB50JX was T6 BA7S, so I bought it to replace the entire socket to convert it to LED.
The Universal T10Wedge Bulb could be used, and the fit was just right, not too tight and not too loose.
Although there are inexpensive Manufacturer unspecified products available in the market, we prioritized reliability.
If possible, a longer pole wire would improve handling and workability.
View detail