Reviews
Used for Torque management of brake hose banjo adapter tightening
Aluminum banjo to avoid cracking and splitting due to over-tightening.
Wobble is minimal and the feel is good.
There are not that many scenes used, but since the price is Reasonable, I don't think it's a problem.
Note that the mounting orientation on the Torque wrench needs to be corrected, so we recommend referring to the WrenchManufacturer's usage instructions.
View detail
Double nut or Shift rod.
I bought it to use for double nut and shift rod.
It is 3mm, or about half the thickness of KTC's 6.5mm on hand.
The angle is 75°, which is not so common, so it is easy to hang even if Arm and Shift rod overlap.
Although there is a problem of strength, it would have been better if the jaws had been made a little smaller, as I don't think that high Torque will be applied to thin-lipped products.
View detail
For CRF250L front axle
Purchased to loosen the front axle of CRF250L.
Although 14mm Hex is not a tool that is used very often, I purchased a solid tool because Off cars often have a lot of suspension modifications and there are opportunities to remove/attach Wheels.
The insert is 1/2, so you need to be careful only there, but it is a stable SIGNET and satisfactory tool.
View detail
I don't use Size very often.
I rarely have a chance to use a 27mm Combination wrench, but I bought a SIGNET wrench with a good balance of price and quality, thinking it would be used occasionally for suppressing Kashimaru-kun's Holder and for Axle Shaft of Big bike.
It is indeed a powerful Size.
View detail
Used with Axle Nut
No problems with this product. I use it with Axle Nut on my off-road motorcycle.
For a moment I thought about substituting Pliers, etc., but then I thought, well, I'll just buy it and add another Socket! (Lol)
SIGNET is a Brand that I trust, so I chose them first based on cosmetics. The performance is also fine.
View detail
For removal of Stem Nut
I bought this for removing the Stem Nut when replacing the Top Bridge on my GSX1300R HAYABUSA.
It works fine, and it costs about 2000 yen if you buy it at Home center, so this one is cheaper.
Info:(Japanese only)
GSX1300R HAYABUSAStem Nut tightening Torque:90N
View detail
Appropriate tools are easy to use
I needed a 15mm Wrench for toe adjustment on my car and always tried my best with a regular length Wrench. I bought a LongWrench because it became sticky and hard to turn if I didn't touch it for a while, and I was able to adjust it easily. I tend to be in an impossible position when adjusting it, so it can be dangerous to turn it with too much effort. I am glad I purchased it. View detail
Cheap but good
The air gun is powerful and has a good volume of air emission. View detail
To the Magic Remodeling Base
[How is it used?
First of all, I would like to apologize to Manufacturer,... I am sorry.
NSR250R (MC21) I purchased this product because I could not turn the cylinder nut under the RCValve of the "R" with the tools I have on hand and had to make a magic modification.
Was the one you received as per Image?
It is a Nut with a 1/4 insert diameter that is quite short in overall length as advertised.
The texture and precision of the Socket are perfect.
How was your experience with it?
If you have ever removed the Cylinder on the Rear bank side of the MC21, you know that it is in a rather troublesome position.
I visited the blog of a person who has made his own by cutting cheap Nut and put it into practice.
As you can see in the photo, I thought I had pushed and shaved it down quite a bit, but the height was still very Limit.
I tried my best to turn the nut with my Spanner, but it was a hexagonal type, so I was able to hold it firmly and remove it safely.
[Points to note]
The insert angle is 1/4, so applying too much Torque is dangerous.
How did it compare to other products?
T2Racing offers a special tool for this nut, but it is so expensive that I was hesitant to buy it.
https://www.webike.net/sd/24576874/
If you plan to work on it a number of times and want to be sure it will work, you may want to buy it.
【Review】
I think the Nut itself is very well made and accurate.
It would have been best if there was a shorter one, but this product was the most suitable for my requirements, so....
It was quite a challenge, but I am glad that I managed to turn the nut.
View detail
Not in Tools Set!
Ducati 900SS needs 11mm for brake fluid replacement with brembo caliper.
When I put Glasses on it to replace it, I found it was too loose with 12mm, and it didn't bite with 10mm... I didn't think it would work with 11mm...?
I didn't have 11mm in my tool box, so I hurriedly snapped up SIGNET's Combination wrench 11mm.
I received the product and immediately replaced the fluid, but it was an exact 11mm. 11mm may not be used very often, but you need a tool.
View detail
I needed it for RamMount.
I was in a hurry to buy this Screw when I tried to install Ram Mount. I had no idea it was Inch. I chose this one in millimeter because I would never use Inch Screw in the future.
I have to look at everyone's Review properly before I buy.
They turned the Screw of Inch well.
View detail
Desorption …
The description said it was detachable, but it could only be used in the detachable direction.
I was very disappointed that it could not be tightened, but since I was able to remove the Filter, which was tightened very tightly, and the construction of the product itself is solid, I think it is not so bad if you break it down.
View detail
Very easy to use socket holder
Mounted on Tool wagon which I always use in Garage.
Magnet will stick firmly to the steel plate.
Until now, it was necessary to use both hands to remove the Socket from the Holder, but the Magnet is so powerful that the Socket can now be removed with one hand.
I don't feel very Stress when I do maintenance and my work efficiency has improved.
I highly recommend it.
View detail
Switch and volume of electronic devices, etc.
It is a MONKEY Wrench, but it is made with a very thin tip.
The basic usage is similar to that of the MONKEY Wrench, but the supplemented design allows tightening even in places where there are other objects just above the occupied portion.
The parts where this would come alive would be the parts that are held in place by thin nut, such as the SwitchBody mounting area.
With Motorcycle, I can't think of many places to utilize it.
In my case, I use it for electronic work as a hobby and for tightening radio golds at work, etc.
It is not used that often.
Normally, I would use a regular MONKEY, and I think it would be convenient, but I don't think it is worth the effort.
View detail
Mine's an older model that's not Twisted, but it's good!
Considering the total of price, accuracy, and appearance, SIGNET tools are
I think it's wonderfully Balanced!
People who like tools too much, when it comes to Snap on, Mac, etc.
I think, Sunday mechanic is necessary and sufficient.
Hex sticking is rattle-free and Plating is Beauty.
This is good for now (laughs).
As you can see, with cheap tools from Home center, there is no denying the possibility of licking, so I thought it would be better to buy a Hex with this precision!
Cowl, footpeg, and Motorcycle have a lot of Hex.
I think there is no harm in buying a good one there.
HexBolt with deep inserts is lick-free
The shallow insertion of the nabe type is suspicious when Torque is hung…
Is it because of the shape of Bolt? I think so.
View detail
reliable Brando -- budget prices!! it is perfect -- it is -- ~.
reliable Brando -- budget prices!! it is perfect -- it is -- ~. View detail
reliable Brando -- budget prices!! it is perfect -- it is -- ~.
reliable Brando -- budget prices!! it is perfect -- it is -- ~. View detail
signet: -- SIGNET:1/4DR 1/4x3/8 socket-adapter product number: -- 11510 description of item [ ] -- [ -- size: -- overall-length: -- the outside diameter ] -- [ -- concave -- the socket of 3/8DR, etc. by the ratchet handle of 1/4DRx convex 3/8DR:26mm:11phi
signet: -- SIGNET:1/4DR 1/4x3/8 socket-adapter product number: -- 11510 description of item [ ] -- [ -- size: -- overall-length: -- the outside diameter ] -- [ -- concave -- the socket of 3/8DR, etc. by the ratchet handle of 1/4DRx convex 3/8DR:26mm:11phimm] 1/4DR, etc.
When using it .
View detail
Since other goods were ordered, it was enclosure, but to the die length (600 mm) of goods, since the box was small, it was aslant put in in three dimensions so that distance might be earned. it was put in as it is without care of health by the box --
Since other goods were ordered, it was enclosure, but to the die length (600 mm) of goods, since the box was small, it was aslant put in in three dimensions so that distance might be earned.
it was put in as it is without care of health by the box -- a sake -- the place of extension of which the upper part breaks through a container box and it jumps out, it obtains even if the hole is also opening the lower part to the box, and it jumps out by a few -- it was .
Although it was satisfactory to the goods themselves, I got it to be better for the packing method to think considerably.
Although connection of improvement hope was carried out by e-mail, since it is nothing (correspondence of what happening after that if it sells, but not knowing), in news, it writes in here.
View detail
Although (+)(-) substitution type of the other company was used, since it had exhausted, it replaced in passing. Although only (+) was mainly used, since it was cheap, (-) was arranged. Is the direction of the stationary type solid too? It is
Although (+)(-) substitution type of the other company was used, since it had exhausted, it replaced in passing.
Although only (+) was mainly used, since it was cheap, (-) was arranged.
Is the direction of the stationary type solid too?
It is not a penetration driver although I think that there are those [ no ] who strike this size.
View detail