Reviews
There are three mouths.
Snap rings are often used to hold down the Kick Arm axis of a moped scooter.
LargeIn the past, I used radio pliers and pick tools as substitutes. It was still inconvenient, though it was usable for the time being, and it took a lot of time and effort to remove the Ring by holding it down and almost scratching the Aluminum case.
My senior recommended me to buy a dedicated pliers and I used it for many years, but the tip of the mouth broke off and I could no longer use it. Once you know the taste of dedicated tools, you can't stand the inconvenience. The last time I used this type, I had to replace the mouth, but the target was not always the same snap ring, and I didn't want to go through the trouble of finding a different mouth each time, so this time I bought SK11's one type with three mouths. It takes up more space in the tool box, but in terms of total area, it is no different from the mouth-changing type. It can't be used in deep places, but I don't plan to use it for anything other than my Dio, so that's not a problem. It is a tool that I don't use very often, but the price is not as high as before. If I need another type, I can buy it again.
After all, Snap ring is not something to work with a substitute tool. We also felt that just using this tool would save time.
View detail
Used to secure Plate to repainted Frame
I bought a battered 900SS (900SL) and am Restore.
For the frames with noticeable rust, I had originally planned to remove the rust by rubbing the paint off with a wire brush, and then finish with a two-component urethane can spray from DAYTONA, Soft99, or Okitsumo.
However, when I rubbed the slightly rusted area...I found that the rust was progressing like a worm crawling under the paint film.
We had no choice but to strip off all the paint, but then the problem would be the MODELPlate that is Rivet-fastened to the frame.
It is clear that the display printed on the Plate would also peel off if the Plate is left as it is, so the Plate was removed before the paint was peeled off.
After stripping the paint, removing the rust with sandblast, and powder coating (we gave up on the two-component urethane can spray finish because the rust in the intricate areas was too severe to remove with a wire brush), the Plate must now be mounted on the Frame. I gave up on the two-component Urethane can Spray finish.
This Rivet was used in that case.
There is no particular element that says, "This is the only Rivet! It is a very ordinary Rivet.
Aluminum Flange、Stainless shaft。
I could have purchased it separately at Home center, but it would have been a hassle to go and buy it, and I bought Rivet along with my other purchases.
There is no absolute necessity to buy at Webig, but it is convenient to be able to buy small items such as these all at once.
These ultra-fine Size Rivets are I went to the home center and it wasn't there. What a frequent occurrence....
It may be a little cheaper if you buy from a specialty store like Monota0u, but if you consider the shipping cost and the hassle of having it delivered by RoseRose, it is more economical to buy from WeBig for a small price difference.
And there's no way I'd buy just this one.
The feeling of using the Rivet is very normal, so there is nothing special to say.
If I may say so, it is better to prepare a bag with a zipper if you do not plan to use it up, because it is not designed to be stored when the Package is opened (it is just a Blister pack).
View detail
Just in case when painting.
[How is it used?
EachParts is painted with Can Spray or other paint for TZr50RRestore.
In doing so, I found that there were quite a few paint particles flying around, which I did not notice at first.
I wear glasses on a daily basis, but I bought these to protect my eyes as well since Lens became a little safer and shinier.
Was the one you received as per Image?
It was just as Image.
It was solid like science experiment Glasses.
How was your experience with it?
I am concerned about the pressure until I get used to it, but I need it for my health, so I have to be patient there.
[Points to note]
It is quite difficult to see when it gets dark, so that's where Neck is.
How did it compare to other products?
It is more reliable protection than ordinary Glasses.
View detail
This is enough for the Torx bit socket of T30
[How is it used?
Used to remove the key cylinder from the Top Bridge of a YAMAHA TZr50R.
I had TorqueT40 for XJR400R Rear suspension, but the size was different, so I had to purchase additional TorqueT40 as Single Item.
Was the one you received as per Image?
It was just as Image.
I checked the size in Home center before purchasing.
How was your experience with it?
It works fine. SK11 is very good for DIY riders because of its cost performance.
[Points to note]
Not particularly
How did it compare to other products?
Torque is rarely used on domestic cars, so I think that SK11's most cost-effective tools will be enough without buying expensive ones.
View detail
Hammer for punching
[How is it used?
I was looking for a large hammer because I had only a small hammer to smash during maintenance, and a large hammer is also a small hammer.
Anyway, I bought it because it was big and looked sturdy.
Was the one you received as per Image?
It has a reasonably Limit weight to support with one hand.
It was quite ideal.
How was your experience with it?
It is useful in many ways, such as tapping the Shaft and Shock driver.
I have been handling it roughly, but so far there has been no damage.
The grip of the handle is also good so it does not fly away.
[Points to note]
It has a reasonable Size feel to it, so it is difficult to store.
Also, since considerable force is applied to the parts, there is a possibility that the parts may be destroyed if the work is done in a frustrated manner.
How did it compare to other products?
The power is different than the chubby Hammer I had on hand.
【Review】
This tool is unnecessary if you just want to maintain your Motorcycle normally.
It can be used to pull out rusted or stuck shafts on immobile or abandoned vehicles.
View detail
Moderately useful Ratchet
[How is it used?
Used for installation of purchased parts and simple maintenance
How was your experience with it?
I like the Small TypeHead Ratchet because it makes it easy to access tight spaces, which is often the case when messing around with motorcycles.
Furthermore, the handle is made of resin, so even if you accidentally hit the body of the car when you turn it quickly with the Head, it will not be damaged thanks to the resin, which is a very high point.
Socket is also push-locked and smooth with 72 GEAR
Cost performance is quite good.
How did it compare to other products?
I also have KTC, Tone, and Koken Ratchet.
SK11 is by far the smallest in terms of head compactness.
I don't think it can handle LargeTorque, but for light maintenance, this is sufficient.
[Points to note]
Unlike KTCetc., it is not overhaulable, so if it breaks, you have to discard it.
I'm sure you will be able to find a new one. I guess the good thing is that it is inexpensive and can be replaced without hesitation.
Buy one as it is easy to use as a miscellaneous tool.
It is easy to use, and I am sure it will become the number one in use.
View detail
Cut
The price is not that much, and it has a good feeling of ease of use.
The handlebar is large, easy to grip, and easy to apply force.
It is also nice to be able to change the position of the blade with Slide.
View detail
Long is needed and
When using the Castle Nut 24mm Socket (3/8 9.5mm) for Elumi's chain adjustment, we wanted a longer length for the Ratchet Handlebar and decided on this product, which can be used in six different lengths from 255mm to 370mm and can also be used in shorter lengths, which are used more frequently.
I used it fully extended this time, and it is easy to use due to its length and moderate weight. Also, the bend at the tip was effective in preventing the hand holding the handlebar from hitting the Fenderretc.
I usually use a ratchet handlebar with a length of 230mm or less, but it is also good to have a telescopic product for motorcycles, although it is used less frequently.
View detail
under compulsion
I lost my 24mm Socket for Elumi's Castle Nut, and although I rarely use 24mm, I needed it, so I purchased the SK11 SK11 Socket 24mm this time, considering the cost performance.
9.I was torn between 5mm and 12.7mm, but decided to go with 9.5mm since Motorcycle uses 9.5mm as a base.
The quality is good and they are a reliable Manufacturer that I have purchased many other things from.
View detail
Plug replacement
This Plug wrench made the replacement easier.
It is very helpful to have it as an in-vehicle tool so that when something is wrong with the plug, I can immediately remove it and check it.
View detail
I thought I wouldn't have to do without it, but I finally got my hands on it.
[How is it used?
ESTRELLA's filler cap is a type with a minus cutout similar to the Timing Hole Plug, but it is usually opened with a slotted screwdriver with a large slot, so I have not touched the coin driver. I have not touched the coin driver.
One day, I tried to open the filler cap with a slotted screwdriver to put in oil, but I got stuck... I didn't want to do it, but it was an emergency and I tried to open it with a coin, but the coin lost out.
I finally reached out to Coin Driver because I knew I could not turn my back on them.
Was the one you received as per Image?
Although the shape itself was the same as the product image, the actual product seemed smaller (compact) than I had expected.
This was not a problem, as the compact design is more convenient to keep in a tool box.
How was your experience with it?
It was the first time for me to use the Coin driver, and I was a little worried if it would fit because there was no description of size and so on, but I was able to use it on ESTRELLA and Filler cap without any problem. I was able to open it safely.
[Points to note]
Even though it is a Coin driver, I think it is indeed useless if the Size is not right.
It is a good idea to check the Size of the part to be used before purchasing.
How did it compare to other products?
It definitely works better than Coin.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
The same thing as 100s?
[How is it used?
Used to apply or scrape off Remover in paint stripping operations.
Was the one you received as per Image?
Not possible and not impossible as per Image.
I noticed later that it is almost the same as the one sold at 100s?
Are they differentiated by Carbon content, etc.?
How was your experience with it?
Quite easy to use.
Remover is Gel-like and hardens after a while.
When applied with a brush, the tips of the bristles immediately harden and Large strange.
This Scraper can be spread on Beauty and is useful for scraping off the paint when it peels off.
[Points to note]
Paint remover also attacks resin.
Inevitably, the tip of the Scraper will be scraped off by the release agent, so it is practical to replace it with a new one after a certain amount of time.
View detail
Socket
Combined with the Small Type Ratchet, it is very useful for compact use in tight spaces.
Single Item sales, affordable prices are helpful.
View detail
Ordinary Socket
Motorcycle Stand Lift I purchased this for the purpose of lifting Jack.
Lift up the BOLT Shoulder Bag, but it is a one-person Motorcycle straddle and cause the Jack under the belly Quantity.:Set.
At this time, the BOLT Shoulder Bag has a very good footing and a low center of gravity, so the Motorcycle is less likely to become unstable even when bending forward.
When I operated the jack for the first time after purchasing it, I used my MONKEY Wrench, but I thought a manual ratchet wrench would be more convenient for operating the jack, so I decided to use this product, which has a standard that fits the ratchet.
Since the main application is Jack elevation, I think the durability is infinitely etc.
I have operated with Impact wrench, but it is difficult to operate Throw alone, so I think Hand tool is better without danger.
View detail
Quantity:1pc. is Large size
The cloth is Large and it is good to cut it. View detail
In addition to removing the interior lining
I bought it to remove the interior lining of my car, but I thought it could also be used to remove and install the Fuel Hose, so I tried it and it was very easy to remove.
The width is 10mm, so only the tip can be inserted, but the Fuel Hose is also new, and it is easier to take out the Large because I used to have a hard time taking it out.
Of course, it can be used to remove the interior lining without any problem.
I am satisfied with the low price.
View detail
angle
It is useful because the angle can be changed for use in tight spaces.
It is reasonably priced, compact, and takes up little space for storage.
View detail
Axle Shaft, etc.
I bought this to replace the Wheel on my ZrX1200R.
I used it to loosen an Axle Shaft and it was easy to apply force.
Other uses would be useful, such as loosening the nut on the wheel of a car.
View detail
Magnet is good.
Thanks to Magnet, it is very easy to put on and take off.
I would recommend this to anyone who struggles with Plug replacement.
View detail
As an on-board tool for motorcycles
I purchased this as an on-board tool for my motorcycle.
I had a Socket set as my main tool, so the low price and the One Touch Socket Holder were the deciding factors in my decision to purchase it as an in-vehicle tool.
The quality is perfect for normal use, as is the low price.
View detail