Reviews
Shape differs from the photo shown!
The photo shown here differs from the photo of the item sent to us.
The photo shows a slightly angled one with a split center, one side was Straight, so I bought it, but the one I sent is 90° right-angled, and the other side is a slightly slanted shape, which is totally different.
Only the color is the same in purple, Material seems to be resin and scratch resistant and looks good, but the shape is different from what I wanted. The price is not good.
View detail
I found it difficult to use myself.
Maybe I am clumsy, but I was able to apply it more neatly when working with FreeBand. If you are dexterous, this is a good product. View detail
Seriously, Garbage.
It was fundamentally broken after 1 shot of use! Seriously Garbage. View detail
I will never buy from them again.
I used it to disassemble the front fork of a scooter, but the tip broke off immediately. In the end, I used a thousand pieces of the same piece in a quantity of 1,000.:I bought 2pcs and managed to remove the C-ring. View detail
Probably shoddy
I was able to use it, but the bearing assembly of the rotating part is not right.
The rotation at the time of jack-up is terribly heavy because of it.
As delivered, the grease of the moving parts was dirty and covered with iron powder and dust,
I took it all apart and Greased it up again before using it.
View detail
I can't connect to the dedicated Site at all, so no.
If you don't improve Site, it will be useless. View detail
Fits: BMW K1600B, BMW K1600B, BMW K1600GT, BMW K1600GT, BMW K1600GTL, BMW K1600GTL, BMW R1200GS Adventure, BMW R1200GS Adventure, BMW R1200GS Adventure, BMW C600 Sport, BMW C650GT, BMW F750GS, BMW F800GS Adventure, BMW F800R, BMW F800R, BMW F800R, BMW F850GS, BMW F850GS Adventure, BMW K1200GT, BMW K1600GT
high
KTC's Hexagon socket was half price, so I bought that.
Inch size, so it's not available in stores.
View detail
BEWARE this will not fit as advertised additional part are needed in order to fit,
As the heading says, this will not fit purchased as is. It is not clear on the site, but an additional part is needed in order for it to fit. I dont know what to do now order the part (Costly) or shelf the tank. View detail
Acceptable as a cosmetic Bolt
When tightened with a Hexagonal Wrench, the Head cracked from the attachment point of the Screw.
I don't think it can be used in places where scattering hangs.
View detail
I tried to exchange Seals.
I tried to replace the oil seal on the crankshaft of my LEAD125.
I couldn't replace it because the bracket was pulled out of the grip and the end of the pin was deformed.
I don't know if the strength is too weak or if only a smaller seal can be pulled out.
View detail
Not Happy
Its not clear you need another bracket at all , almost misleading to be honest. I dont even think the other bracket would work. Dont buy as misleading. View detail
Not for groms.
Purchased for installation of High Camshaft on Grom, but it was too short to fix. View detail
I will never ask again.
I had never asked for anodizing, but the corroded areas were untouched and anodized as they were. The appearance and finish looked as if it had been sprayed with matte LacquerSpray by an amateur.
I asked for this as a Large hand, but I have nothing but regret.
I personally recommend powder coating.
View detail
Poor.
I bought it because I thought it was cheap and good that the tip could be replaced.
The downside of the tip replacement is that it often hits too many areas and cannot reach tight spots.
The C-ring is so hard that the tip is useless because it is wobbly.
At any rate, I can't RECOMMENDATION because there are so many irritating POINTS.
We managed to finish the work, but it was a Level we never wanted to use again.
Tools are Large stamps.
View detail
4.5L？？？
Although the label indicates 4.5L, even 3.9L of Oil could not be sucked up, leaving the Oil in a liquid state.
Is it really 4.5L?
View detail
Another long Pin would be perfect.
Normally, I would expect to see a Pin that pushes out the Chain Pin and a longer Pin that pulls out the Chain Pin.
This one comes with only one type of Pin.
Therefore, it is necessary to push out two Pins, remove the Plate, pull it out and push the ThailandPin to the end.
That is a bit of a hassle, but for the price, this is what you get.
However, the fact that the tool is Compact is a Large change Good.
View detail
Babyface Hose clamp
I purchased the same size to match the 7Φ of the KRH hose, but the size did not fit and I could not clamp it. View detail
Fits: Others , HONDA GROM, HONDA MSX125, HONDA MONKEY125, HONDA SUPER CUB110, HONDA CROSSCUB110
Not used for jc92Clutch work
Center nut of jc92 Clutch turns in a box of 19 View detail
Not used.
The exterior arrived in a busted up state.
Since the pieces are not in the Corrugated cardboard, I'm going to assume that you sent me a piece with a busted up exterior.
View detail
Not into TTR. (___;)
Not into TTR. (___;) View detail