Reviews
Is the length of the short method better?
I tried to make a 15-socket holder, but I didn't think about the length of the holder. I didn't think about the length of the holder, because it was about 30cm long, so I couldn't fit it in my tool box. 10-socket holders are available in the Quantity:2pc. I should have bought Set. But
It is definitely better than the Gold genus because it is made of plastic.
View detail
Poor mechanics buy toolsRose
9.The 5 tools were added in the Grip set since the number of tools has increased since the Rose purchase. The work is easy Plus No.2 Driver.
Only 1 pc.
View detail
Extremely common products
The Vinyl bag, which was only slightly touched by the residual heat of the exhaust pipe, melted and leaked waste oil when it was tied up with the tie wrap. It would be appreciated if you could change to a Vinyl bag with higher heat resistance.
Into
View detail
Chain brush
I continue to use it because it is easy to use and inexpensive. View detail
First Oil Replacement and Oil Filter Replacement
Purchased to replace Oil and Oil Filterfor replacement of DL1000 V-STROM250 for the first 1000 km.
The oil capacity of this Motorcycle is 2.1L, but when the drain bolt is removed, the oil is in the horizontal direction.
I just bought this Size, which is a little on the Large side, because it seems to pop out,
It was just great to receive Oil as well.
I also liked that it came with Vinyl gloves and a tie band to tie the bag after work.
I will use this one for my next oil change.
View detail
Fits: SUZUKI SKYWAVE650 burgmanLX, SUZUKI DL1000 V-STROM650X, SUZUKI DL1000 V-STROM1000, SUZUKI DL1000 V-STROM650, SUZUKI GSX1300 HAYABUSA, SUZUKI V STROM 650, SUZUKI V STROM 1050
DL1000 V-STROM250 for initial Oil replacement and Oil Filterfor replacement.
I purchased this for the first Oil replacement and Oil Filterfor replacement of DL1000 V-STROM250.
I was able to replace the Oil Filter without any problems.
The Bolt hole in the middle makes it easy to remove the Oil Filter.
View detail
I will never buy from them again.
I used it to disassemble the front fork of a scooter, but the tip broke off immediately. In the end, I used a thousand pieces of the same piece in a quantity of 1,000.:I bought 2pcs and managed to remove the C-ring. View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA
good
I think it is worth buying because it can be used for various types of cars!
It would be nice to have one, especially for a 4MINI, as it will be used more often!
View detail
I finally bought it.
[How is it used?
I bought this to replace Chain.
I've been wanting to get one for a while,
This is a moderately high-end product, isn't it?
It's been 10 years since I put it off, thinking about how many times I'll have to replace the Chain before I die,
I decided to buy it because I mainly play Race and I thought that the frequency of Chain exchange would be there as well.
How was your experience with it?
The Instruction Manual was properly included so I could use it with peace of mind.
I used to use tools like Chain Tool only or Crimp only and I would ruin them quickly. (I would like to believe that my usage was not good)
It can be used simply because it has few configuration parts.
Also, the cans DID look stylish. Cool.
When I opened the lid, it was skunky, so I put the Sponge that came with Brake Pads underneath to make a Cushion.
[Points to note]
I think it will not be a problem if you read the basic Instruction Manual, but you might want to buy a spare pin for cutting.
If it breaks, the motorcycle will not be able to run!
View detail
Can also be used for Mirror shield
The Mirror shield of the MotorcycleHelmet can crack or deteriorate when cleaned with aggressive cleaners, but there is no such concern with this product. The Merit of the Largeest Merit is its portability, which allows it to be brought along on day-trips. Even in the summer, water will not fly out of the bag. "Dried out." I am glad that I can use it normally without any problems. View detail
KITACO KITACO Spring hook
This is a must-have product for spring installation and replacement. I have personally purchased and used KITACO products for a long time, so I purchased this product this time. View detail
Engine overhaul essentials
[How is it used?
I purchased this for Gasket removal and chamfering of mating surfaces during Engine O/H on a TZr50R.
Oil is the same DAYTONA's exclusive oil.
How was your experience with it?
Scraper alone could not remove all of the gasket that had been stuck for many years, so I used oil stone to clean the gasket thoroughly. I soaked it in 4st Oil at first to soak it up because it absorbs Oil quickly at the beginning of use.
After that, special Oil is applied and polished at the time of use as shown in the video.
How did it compare to other products?
I don't know about otherManufacturers, but I was worried about purchasing the number 600.
However, since Gasket removal was going to be the main focus, I bought the 400.
There was no problem here.
[Points to note]
If you continue polishing, you will run out of Oil and the sound will change, so you will need to add Oil immediately.
Be careful not to damage the object when polishing with a piece of Oil.
View detail
Cheap, but not easy to use.
[How is it used?
Used for Engine O/H of TZr50R.
In particular, a universal holder like this product is needed to remove the fixed nut of the Clutch.
Was the one you received as per Image?
We selected this product because it had the lowest Gold amount.
To be honest, I thought the cheap price would make the product quite poor, but it was not as bad as I expected.
The supplier may be the same as the ones offered by other Manufacturers because the pictures are the same.
How was your experience with it?
The ease of use is not all that great.
In the case of TZr, the fixed pin is hooked to the clutch housing, but the fixed pin is short and easily comes off,
I cannot apply force well. I have the impression that the size is not right for 4EUEngine, although it may be just the right size for other Scooters.
[Points to note]
Be careful not to put the fixed Pin in the wrong place.
I used it on two engines and accidentally put a pin on the bolt hole of the clutch, destroying the bolt hole.
How did it compare to other products?
Similar products are lined up at similar Gold prices, as if the suppliers are the same.
Once you buy one, it will last a lifetime, so you might as well get something a little more decent.
View detail
Required for 4EUEngine Overhaul
[How is it used?
I purchased this product to use for Engine overhaul of TZr50R.
The 4EUEngine Flywheel of TZr50R uses a special screw diameter and requires a special tool for this type of vehicle.
Was the one you received as per Image?
The product was exactly as shown in the Image and comes with the Instruction Manual, so it is ready to use as soon as it arrives.
How was your experience with it?
The quintessential product is a dedicated product and is quite easy to use.
Conversely, this is the only use for this Engine, so in a sense it is too much to handle.
To use the Fly Wheel Puller, attach the Fly Wheel Puller to the screw thread on the Crankshaft on the Flywheel side as shown in the video.
While holding it in place with the MONKEY, turn it. If it becomes very hard in the middle, you can easily loosen it by tapping it lightly with a rubber hammeretc. to give it a vibration. In my case, I pushed it through by force.
[Points to note]
Nothing special, but try not to damage Mt. Screw.
How did it compare to other products?
The competing product is the YAMAHAOEM SST, but the price is not much different, and this one is more economical since it comes with a point.
View detail
Double nut or Shift rod.
I bought it to use for double nut and shift rod.
It is 3mm, or about half the thickness of KTC's 6.5mm on hand.
The angle is 75°, which is not so common, so it is easy to hang even if Arm and Shift rod overlap.
Although there is a problem of strength, it would have been better if the jaws had been made a little smaller, as I don't think that high Torque will be applied to thin-lipped products.
View detail
Used for Wiring processing
After all, using a decent tool will ensure a clean and fast completion.
This is one product I wish I had bought earlier.
View detail
Purchased due to the appeal of the cosmetics.
First-class products are always better, but I thought that a measuring instrument of this price would be sufficient. It is more reliable than no management. There are many comparison videos on Youtube, and I found them to be very helpful. If you want to be absolutely particular about tools and equipment, I recommend you to buy a first-class product from the beginning because you will lose money by buying a cheap one. View detail
safe (secure) in one's possession
8mm Hexagon Bolt is Quantity:It was hard to find a tool set that came in a set, but when I saw it, I bought it immediately.
Combined with the included Ratchet, tightening and untightening was very easy.
View detail
SmallEngine Displacement Volume can be used 4 times
I like them because they don't leak and they are inexpensive. My XG250 TRICKER has been used 4 times in one box, and I like it because it is cheaper than similar products available at Home center. View detail
Just the right size for a Small Type car
I think the size is just right for replacing oil in Small Type cars. I think the price is also normal. View detail