Reviews
Used for Under Cowl in yzf-r25
I could have used aluminum tape, but I didn't want to worry about it melting or burning. View detail
It comes with adhesive Seat and has a high heat resistance temperature.
Used for Heat Guard on DUCATI 848.
In the 1098 series, the Exhaust System meets under the thigh of the Right leg, so it gets unthinkably hot in a Japanese car.
The external Carbon heat guard has already been burnt out.
I purchased this product to stop further progression.
There were also overseas products, but DAYTONA is still the safest choice.
With adhesive Seat, itself heat resistant to 100°C and not in direct contact, it was perfect for my needs.
Cutting with Scissors is also easy, and the glass fiber does not scatter that much. (Mask is recommended).
The adhesive was strong enough, I have used it for several months and nothing has peeled off.
It used to be hot even through the Gloves, but now it is not hot at all and I can even touch it a little with my bare hands.
It is not expensive and is a good product.
View detail
Insulation Seat
I purchased this product because when I replaced the Tank with another color Tank on my SR400, the OEM Insulated Seat was not attached.
The texture is thinner and harder than the OEM insulated Seat, but it does not look cheap.
View detail
Purchased for attaching to the inside of an external Under Cowl
I noticed that the part where the Exhaust System was in contact with the external Under Cowl was slightly melted, so I hurriedly purchased this product. I drove several hundred kilometers after applying the product, but I did not see any deterioration of the Under Cowl due to heat. It helped me a lot. At this point, I would give it an All 5. I hope it will last for a long time without any deterioration. View detail
For Tank and Radiator hose
I put it on EXC-F Tank and Radiator hose.
Tank was too thick to apply with other heat shielding Seat, so we applied this one.
Even though it is not as thick as a proper heat shield Seat, so the effect is not half as good, it is still much better than nothing.
I have had a tank deform due to heat and leak gasoline, so I am hoping this will be a solution to that problem.
The radiator hose is close to the exhaust pipe and is not particularly heat-resistant, so coolant blows out quickly, and the heat can cause holes in the hose.
It is very easy to use because it can also be attached to the back of Cowl.
View detail
New ModelGSX1300R HAYABUSAMagical racingSide cover was used.
As I mentioned in my recent impressions, I thought the Carbon Side Cover was too thin and would burn my inner thighs. So, I decided to use it.
I talked to Dealer and he recommended 2Quantity with room to spare.:Set purchased. Impressions.
If you want to put it on the wrong side of the wall, or if you want to put it on the wrong side of the wall, you can use the 3Quantity.:It may be safe to Set.
The ride no longer feels hot, so there is a definite effect.
I'm not complaining, but I was only concerned about the slightly longer delivery time (about a week for me).
View detail
Adhesive enough
It can be cut to any size, so it can be stretched to fit any location.
The adhesive is firm, so it did not peel off after application.
The heat resistance effect is sufficient and effective in preventing deformation and discoloration of the Under Cowl due to heat from the exhaust pipe.
View detail
It is used for the exhaust pipe of the Exhaust System.
This Glass Wool is used for the exhaust pipes of the Exhaust System. It is relatively inexpensive and the material is easy to roll, so it is easy to work with. View detail
It is good
I put it on the back of the Side cowl.
The heat from the Exhaust System is also Shutting out and the Cowl is not melting.
It sticks firmly to the surface, so it can be used as a
There is no Trouble that peels off after a few years.
Very good stuff
View detail
It will last for a long time
I put it on the reverse side to protect the Cowl from the heat of the Exhaust System.
It seems to block the heat and none of the Cowls melt or get hot.
It's been taut for about 10 years.
It has not peeled off or deteriorated, so I think it is a good product.
View detail
Good horizontal Size feeling.
I was looking for a replacement for the Heat Insulating Material inside the Side cowl of my TZr50R as it was peeling and falling apart.
The chamber and exhaust pipe are along the side of the side cowl, so it is good that it is horizontal.
The deciding factor in the purchase
I bought it because the horizontal size is just right and it was inexpensive.
Since this is an A-Tech product that deals with a lot of exterior parts, I thought that the selection of the Heat Insulating Material would also be correct, which was also a deciding factor.
[Impressions of using it]
The Heat Insulating Material comes with double-sided tape and can be marked on the backing so it can be cut out Exactly.
I don't know how well it shields the heat since I haven't checked it properly after installation, but it looks fine.
Products compared
We compared it to Striker and Posh Heat Insulating Material.
I chose this product because it was in stock, had a good Size feel and was inexpensive.
【Review】
I'm glad I bought it because so far the adhesion and thermal barrier performance seem to be fine.
Now I'm hoping it will last a long time.
View detail
DIY Heat Guard Production (・∀・)
When I was looking for Heat Insulating Material to make Heat Guard.
This product has been found (・∀・)
It is less expensive than similar Insulation Glass Wool.
The heat resistance temperature is relatively low at 200-350°C, but it was sufficient for our purposes.
And the release paper on the back is easy to draw lines on, and it's just the right thickness.
I think it was easy to process. (Translated by ω-) b
If I had to pick a favorite, I'd say the Large width would have been better.
View detail
GORILLA・Full CowlSpec.
Created a GORILLA Full Cowl vehicle and used it for Cowl and paint protection.
Since the Exhaust pipe on the Over is going through the Limit.
It's not painted yet.
View detail
GORILLA、Full Cowl
I am currently building a GORILLA Full Cowl car and bought this to protect the Cowl and paint from the heat of the Exhaust pipe.
It's not finished yet, but the size is good for Small Type car.
View detail
Insulating effect
My own motorcycle has a Center out, so my thighs and butt get hot, and it's an afterthought To protect electronic devices and pipes, etc. from heat, the inside of the heat shield and the exterior surface of the It works quite well and I am very happy with it
But if you cut it, Glass Wool will wispy, so you need to be careful with it
View detail
Purchased for Under Cowl's protection
I use it to protect my Under Cowl After about 10,000km of use, the silver foil-like part of the surface has come off, but Heat It seems to keep its performance as an Insulating Material, and for now, Cowl is the only one who can do it It doesn't burn or anything I like having a sticky surface View detail
It is easy to use with Double-sided Tape.
It is easy to install because it has a powerful double-sided tape that is hard to peel off.
The place where Cut was done is fuzzed, so it was protected with Aluminum Tape.
View detail
good
I tried to prevent deterioration of the 2 st Oil tank of the CRM 250 rr due to heat. Because the shape of Tank is not square, it was hard to stretch, but it stuck well. When I touch Tank after running, I feel that the heat has not been transmitted more than before. I will stick to other parts and check the effect. View detail
Thermal insulation tape
When installing the outside RightAir Scoop outside the buell, the intake manifold comes very close to the position, so I bought this product for the prevention of Scoop's dissolution.
Easy to handle, easy to cut with scissors in any shape, you can stick to small places.
It was affixed to Scoop a little Large, I confirmed the engine start condition, but there was no change in shape, securely insulated Scoop and insulated.
I think that it is exactly good for the protection of Under Cowl by the heat from the intake manifold such as SS.
View detail
Insulation Mat
Since buell is a V-type 2-cylinder Engine, hot air from Rear bank is caught under Seat, Seat is very hot and sitting is painful and I was thinking about something..
After finding this product which we are watching a lot and evenly sticking it under Seat, I felt almost no heat, became very comfortable and became able to concentrate on driving.
I really bought it!
View detail