Reviews
Useful for Wiring protection and concealment
Useful for concealing and summarizing Wiring
Bend it about 45 degrees toward the uncracked side to open it up and put it in.
It is recommended to install it near moving parts or near the heat source.
This time, I protected the Cable on the front of Camera in DriveRecorder!
View detail
Useful for Wiring protection and concealment
For fine lines, φ3mm is sufficient
Only one Plus wire (ACC power etc.) so it is ideal for protection!
View detail
Fits: HONDA XR250, HONDA CRM250R, HONDA CRM250AR, KAWASAKI KLX125, HONDA CRM80, HONDA XR230, HONDA CRF230F, YAMAHA WR250X, YAMAHA WR250R, YAMAHA SEROW250, YAMAHA XG250 TRICKER, SUZUKI DR-Z400SM, SUZUKI DR-Z400S, KAWASAKI KSR110, KAWASAKI D-TRACKER-X, KAWASAKI D Tracker, KAWASAKI KLX250, KAWASAKI D Tracker 125, HONDA CRM50, HONDA CRF250M
I'm not sure about the electrical system, but ….
I purchased the Racer to make it a public road Spec.
Quantity of electrical components:I could have bought it as a Set, but I bought this one because I can reconfigure it in various ways.
These are the Parts that are required when using LEDs with DRC's Kit.
View detail
Male terminal Cover Only
This is a Male terminal Cover Only product. Male and Female terminals (Female terminal Cover) are required separately.
Since it is not waterproof, we recommend the purchase of a Waterproof Terminal Set if the connection is to be exposed.
Motorcycle and car Waterproof is rarely seen only in Connector, so I don't think it will be a problem, but it is a good idea to buy it according to your needs.
It is better to have it in Large quantity so that it does not roll around somewhere and disappear because it is a Small item.
Contact between terminals and frames may cause damage to electronic equipment or, in the worst case, cause a fire.
View detail
Hard but strong!
It has a slit in it and you put the wiring inside, but it's just too hard! It is not flexible, so it is hard to put in and take out the wiring, and it is not easy to handle! However, this is one of its strong points and its durability is outstanding! I mainly use it to put together the ETC and sub-computer wiring inside the motorcycle! It is a recommendation because it is very useful if used in the right place at the right time! View detail
Expected
I was concerned about the dim glow of the post-attached (added) Indicator, so I decided to add a rectification Diode.
When I replaced the meter with a Universal one this summer, there was only one warning lamp, so I purchased an LED lamp from KIJIMA and added an Indicator Lamp, but the Red Lamp was glowing dimly. Well, if I didn't care about it, it would have been fine, so I didn't touch it until now, but recently, I decided to add a rectifying diode while reviewing the wiring.
After following the instructions and incorporating it into Wiring, I was able to eliminate the blurriness of the Lamp, but Wiring became so long that it was difficult to store it.
View detail
Used when replacing crf250rallyRear blinker
Used when replacing crf250rallyBlinker
LeftBlinker is Orange.
However, the Minus-side Connector is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
Used for crf250rallyRear blinker
Used when replacing crf250rallyBlinker
RightBlinker is Blue.
However, the Minus-side Connector is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
Frosted Material with high texture
I used this product to wiring up my Ninja250SL's sub-computer and USB. Honestly, you can use Curing Tape instead of this product, but this product is pre-cut, so it is easy to work with, and it looks overwhelmingly good, so it is a Recommendation! View detail
A friend of old cars?
I'm not sure about current vehicles, but this is a common two-turn Bullet Type Terminal on older vehicles.
I get the impression that there are a lot of them, especially around Tail.
View detail
Although the shape is different from those made by Ekimon, Yaoki, and others.
The Crimp section has not been modified in any way, such as being slightly folded from the beginning, so it is a little troublesome to Crimp with Electric Works Pliers, but it is good for Crimping several thick or thin Cables at once.
In addition, the sleeves for waterproof and insulation are a little thicker than those of the Title companies, but there were no particular problems when they were mixed with those made by those companies.
View detail
male and female terminals
Provides quality and texture with Honda Std products I was able to do what I wanted to do with the feeling of use Please contact Crimper for the products you want to buy together Easy installation It is recommended to purchase several bags with high price performance and compare them to other products as a set WeBike packaging is always good. Shipping and packaging will arrive in a week Concerns and Precautions When purchasing, you may not only purchase by looking at pictures, but also carefully read or incorrectly purchase products consisting of men like me. This product consists of a terminal for men and a terminal for women View detail
For additional Wiring
I found an article that the Bullet Type Terminal for Motorcycle is slightly different in size, and it seems that it is not Exactly fitted to A0 products, so I bought one to try it out.
I do think it's harder to pull off than A0.
Why would they change the Size?
And I didn't know there was a difference even among MotorcycleManufacturers.
It's an essential component for safe Wiring processing.
View detail
By Location!
When wiring, Wiring Tube is used for the wiring itself, and Coil type Wiring Bando is used for the Bullet Type Terminal and the Jack portion. The Wiring type is easier to use than the Tube type for these joints because it is easier to remove immediately. View detail
Wiring Summary!
The Wiring Tube is a good product for refreshing the wiring, because it is hard to tell which is which when you're wiring and it can cause stress buildup. View detail
Wire standards
Both EmonAV1.25sq and DAYTONAAVS1.25 are probably stranded wires, but Emon has a thicker and softer coating, while DAYTONA has a thinner and harder coating, which is said to be similar to OEM harness. Incidentally, "sq" stands for "Square," and "AWG" is called "Gauge" (AmericanWire gauge) in the United States wire standard, indicating the cross-sectional area of the conductor section. AWG16 = 1.25sq = 1.31mm2. The larger the AWG number, the smaller the cross-sectional area. If it is just 1.25 and only a number, it may be the diameter of the conductor, but is there any diameter notation for stranded wire? View detail
Very inexpensive.
I would like to install a new Grip heater, but I would like to calculate if the heater is Large enough to interrupt the wiring between the USB port and the Relay. The maximum charge current of the two electrical components is 3.3A at 13.5V for the Grip heater and 4.8A at 5V for the USB2 Port (5V is switched on and off), totaling 8.1A. I bought Emon's AV1.25sq. The available power is 140W or less for 12V cars and 280W or less for 24V cars. If converted to allowable current, it is about 11.6A? Although it is within the allowable range, it is not as high as DAYTONA's AVS1.25 (A) of the same size.:Auto for Vehicle Low Voltage Power Line, V:Vinyl、S:The price is 1/8th of DAYTONA in unit length, and Emon is very cheap. By the way, it is another Wiring, but the most large current of ETC on-board unit seems to be less than 1A because it is 1AFuse, although only standby current was written. View detail
![[Trip Machine]CABLE WRAPS](https://img.webike-cdn.net/catalogue/images/116588/000000013076-05-xl_TS.jpg)
unusual
I have never seen custom parts before.
Leather Cable Wrap. Grip, Bag, and TankLeaf are all from TripMachine Company. I think this will be a brand to watch out for in the future!
View detail
It can be used normally
The female side of the Harness was too stiff, so I used this product to change it. If you tighten it too hard, the cable will break and the connector will become useless, as is the case with other connectors. View detail
SR400 Electrical Equipment Plate installation
Shallower than expected, Battery feels less secure. View detail