Reviews
took a chance and it payed off
Snapped the original cable. Ordered the short cable for the standard Z900RS after fitting lower bars. Worked out within 10-15mm of the Z900RS Cafe OEM cable length. Great fit. Fast shipping as always. View detail
Fits: KAWASAKI ZEPHYR400, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR750 RS, KAWASAKI ZEPHYRX
HURRICANE 10cmLong throttle cable
Long cable was replaced when the handlebar was replaced.
Handlebar is HURRICANE's POLICE2 type with 27mm up set up holder compared to NORMAL.
OEMCable was not enough, so we decided to use a 10 cm long cable.
I think it fits nicely without being too long.
The replacement was done by one person, without removing the carburetor, so it took more than 30 minutes to hook up the new roll of Cable,
The return Cable did not take that long, but it was a struggle.
View detail
Fits: YAMAHA XJR400, YAMAHA XJR400R, YAMAHA XJR400R II, YAMAHA XJR400S
I'm lighter
Clutch is now lighter.
Stainless mesh, so it seems to be durable.
View detail
Diversion to CB250F
I installed a ZETA handlebar on my MC43, and it was about 30mm higher, but the OEM tension was too tight, so I replaced it with a ZETA handlebar. 1 pc of pull was applied to the handlebar, and the direct feel was increased by adjusting the play and the handle.:Pair (for Left and Right) I let it have play at full lock. View detail
Fits: YAMAHA XJR400, YAMAHA XJR400R, YAMAHA XJR400R II, YAMAHA XJR400S
Mesh
The mesh is durable and the Clutch is very light.
I would like to do this next time I replace it.
View detail
Fits: SUZUKI GRASS TRACKER, SUZUKI GRASS TRACKER Big Boy, SUZUKI GRASS TRACKER Big Boy
GRASS TRACKER It was a long time for BIGBOY.
It was too long for GRASS TRACKER BIGBOY. We managed to get it to fit in the car by working out how to handle it.
Clutch has been revived.
View detail
Fits: KAWASAKI ZZR1200, KAWASAKI ZZR1200, KAWASAKI ZZR1100/ZX-11
Changed to Long cable due to change to Handlebar Up Type.
I changed to a long cable because I changed to a Handlebar Up Type. It is a little bit long, but it works fine. View detail
It was a little long.
Changed to Long cable due to change to Handlebar Up Type. It is a little long, but there is no problem in use. Conversely, the Handlebar can still be raised.
Installation was troublesome with the carburetor part.
View detail
it work very light and smooth
I bought Hurricane long throttle cable to replace the old on my Honda VFR800 VTEC 2003. Shipping time is a bit longer than 2 weeks after shipping. Hurricane throttle cable is Made in Japan, the cable is long enought to install on my bike, it work very light and smooth. View detail
good quality, perfect fit
Bought these for dragstar 1100 classic. The cables look to be of good quality and fit my bike perfectly. Don't forget to lube the cables before installing them on the bike. View detail
good quality, perfect fit
I bought this clutch cable along with throttle and choke cables. This cable is 100 mm/10 cm longer than stock but I had no problems about them. The fitment is great. Maybe in the future, I may install an ape hanger to my bike and I can use that extra 10 cms. View detail
HURRICANE LongThrottle Wire GPZ900R
I received the product immediately after purchase and am very satisfied with it.
I'm sorry
View detail
Separate handle by all means!
If Separate handle is selected, the NORMAL clutch wire will be too much.
What kind of harm will be done?
The Clutch is not turned off, but it is turned off, or at worst, it gets tangled in the Wheel and becomes Large.
Shorting is necessary to prevent these problems.
It is -100mm shorter than NORMAL.
good point
When separate handle is used, the clutch is cut smoothly.
XX semi-cra is also easy.
There is also the rigidity of the ○Cable.
The price is also low.
A bad point
Installation is troublesome.
○Peasy to rust if lubrication is neglected.
I need a Cable that matches the length of the Handlebar.
For Separate handle, Normal cable should not be done in the sense of prevention.
View detail
awesome
awesome with my 8' bar on the rebel 500 same quality as the OEM cable this bit here is just for the body of this review to reach > 100 charaters geez View detail
HandlebarUp essentials
I had to upgrade my handlebar because the position was getting too tight, but I found this product when I was having trouble getting to the clutch cable. The installation was not difficult and I was able to replace it with the on-board tool. View detail
Reliable Manufacturer.
When I replaced the BEETTAPER Handlebar, the NORMAL Clutch Cable sagged.
I bought this one because it looked bad.
Above is the length Exactly to Handlebar.
View detail
good.
I am a SR400FI user. I purchased it because the length of the clutch cable was tight while using the Hurricane handleset in the past. I have now replaced it with the SR500 genuine up handlebar, but I am using it without exchanging cables. We have a spare for future exchange. ---------------------------------------------------------- SR400FI user. Previously, the clutch cable length was tight while using the hurricane handleset. I am now exchanged with SR500 Genuine Handlebar, but I am using it without a cable exchange. We have extra for future exchange. Powered by Google Translator View detail
HURRICANESlot cable
I purchased this one because OEM Parts has been discontinued.
Brand strength and no quality issues at all.
Replacement requires time since the carburetor needs to be removed and installed.
View detail
Throttle Cable
I bought it because of its Brand power.
Some compromises have to be made because OEM Product has been discontinued.
View detail
Cable poking has been eliminated.
It may not be originally necessary, but in my case, the height of the Handlebar was about 2cm higher than that of the Normal vehicle because of the difficulty of leaning forward, and the Clutch Cable was sticking out when the Handlebar was set to the full Right position. So, we replaced it with a Long Type Cable. As a result, the tension of the cable was eliminated and it became very easy to operate the clutch when turning the U-turn. Although U-turns are rare, I think it is effective from the safety point of view to have eliminated one of the operational concerns in unfamiliar situations.
Since it was not an expensive product and the replacement work was simple, I strongly felt that I should have replaced it earlier.
Around Handlebar for reference (Height change) Attached is an image of the
View detail