Reviews
Fits: HONDA Rebel1100, HONDA Rebel500, HONDA Rebel250
Easy to use
I purchased the Round Type because my ST250 has a circular swing arm. I am satisfied with it and can use it without any problem. View detail
Easy to use
The rear wheels can be used without difficulty, but the front wheels cannot be used. The front wheels are gradually shifting, perhaps because they are stuck in place. View detail
DRC wheel tool anti-vibration/balancer option 10mm shaft set Product # F4287
Thank you for the fast delivery Thank you for the fast delivery Thank you for the fast delivery Thank you for the fast delivery Thank you for the fast delivery Thank you for the fast delivery View detail
Allows you to turn your Motorcycle around in a comfortable position
I bought it because I wanted to enter the garage from the front of the Motorcycle and park it, then turn it around 180 degrees for the next time I exit (I wanted to keep the front of the Motorcycle facing the garage exit side).
There is a similar product, Motorcycle Moveretc., which is used to lift the rear tire by stepping on it with the foot (by the principle of leverage), but when I tried one owned by a friend, I found that this product was easier to position myself in and moved the motorcycle stably. However, since the Side Stand is dragged, I think it is necessary to use it with STANDRoller for vehicles with LargeEngine Displacement Volume. (The same applies to the Motorcycle Mover.)
In terms of price, it is less expensive than Motorcycle Mover, and the quality is not bad, so we felt that Cost performance is high.
STANDRoller is sold separately, but the Quantity:It would have been better if it was a Set sale.
View detail
Ideas products for improved serviceability!
I saw this product in DAYTONANews and bought it as soon as it went on sale.
I had a chance to do maintenance of CRF and SEROW's LINK circumference with just the right timing and used it immediately.
This tool is very easy to work with when pulling out and inserting the Axle Shaft and using it to assist in removing and installing the Wheel, as well as when slightly changing the angle of the Swing Arm for maintenance of the LINK circumference and adjusting it to a position where no excessive weight is placed on the LINK circumference.
When the Hook is hooked and pulled forward, the height of the Wheel is raised to just the right position, and the load can be set to Free, making it very easy to work with the Bolt around the LINK.
It is good to have one if you have many opportunities to service the rear wheel area.
View detail
Nothing beats it, as long as you have the space to put it.
I bought a battered 900SS (900SL) and am Restore.
Everything is RoseRose until Bolt1 pc, then everything is Repair and modified and regenerated before assembly.
Stem bearings and other parts were also replaced, but since they are all RoseRose, it was easy to complete the work by simply turning the FrameSingle Body over and over while hammering.
The Ducati of this era had no dust or oil seals on the stem bearings, and the sliding surfaces of the bearings were exposed in a barbaric manner.
The bearing is really exposed, and even the bearing race can be seen when peering from below at certain angles.
The large washer, which was used in later models, was inserted into the lower side of the stem shaft.
Since it is just a Washer, there is no RubberRip seal, just a little harder to see Bearing and a little less gap with the Frame.
Still, I built it in thinking it would be better than nothing...
When assembled, the Washer effect does not look very promising.
On the contrary, it appears that foreign objects that have been placed on top of the StemBracket have become even more likely to enter the Stem bearing area.
I thought so, but the body is already pretty much assembled, and I don't want to remove parts now to make a FrameSingle Body.
Then there are two ways.
Lift the front of the body in some way or lift the body Front in some way.
The most stable method is to use a Jack or other lifting device.
The weight of the car body rides directly on the hard STAND, so it can lift TIGHTLY and Front.
But it often doesn't work that way, does it?
If it is a 4-cylinder engine, the exhaust pipe is in the way 100% of the time, and even if the exhaust pipe is removed, the oil pan is not flat on modern engines.
This is where the Frame Stand comes in.
As the name implies, you can put up something like a clothes-drying stand next to the Frame and use it like a clothesline.:Pair (for Left and Right) The Tie Down is hung by hooking the Tie Down to a stick passed through the
It is suspended by a string, so it is not very stable, but it is very easy to use.
This product is a super large version of the Frame Stand.
The maximum height of 2m is not a feat!
There is no doubt that the bigger the better, and this product is also much easier to use than the 1.5-meter Frame Stand that is often used by other companies.
It is so big and heavy that it has great rigidity, even when the body is suspended. The "feel" is a little bit like a "bounce. is Zero!
It is comparable to the high-performance STAND, which is sometimes used in motorcycle shops for PRO use.
The only weakness is Super big and super heavy." Things to do!
As you can see, it is a huge large when assembled!
Then I would say disassemble it after use...but no, no, no!
It will not stand on its own when disassembled, and even when disassembled, it is still big enough!
And since it's made of steel, it will definitely be covered in Rust if left outdoors...
in a word "Location matters." But [Color] The ability to Clear is the key to success.
If you are fortunate enough to have the indoor Space to store such a Giant Large item, this is a real treat.
View detail
Easy maintenance of front wheels
I used it to clean the front wheel and brake disc. The rotation was more sluggish than I expected, but after lubricating the roller bearings, they turned smoothly. It is very good because I don't have to move my heavy motorcycle around. View detail
Fits: HONDA CR250R, HONDA CR125R, HONDA CRF250R, HONDA CRF450R, HONDA CRF450RX, HUSQVARNA FC250, HUSQVARNA FC250, HUSQVARNA FC350, HUSQVARNA FC350, HUSQVARNA FC450, HUSQVARNA FC450, HUSQVARNA FE125-501, HUSQVARNA FX350, HUSQVARNA FX450, HUSQVARNA TC125, HUSQVARNA TC125, HUSQVARNA TC250, HUSQVARNA TC250, HUSQVARNA TE125-501, HUSQVARNA TX125
Convenient and lightweight! But low strength
Large change is useful for washing the underside of the Motocrosser!
However, it is so strong that it will bend if you try to start KICK with STAND applied.
If it only supports the weight of the car, there is no problem.
The handlebar can be used as an insert, making it easy to insert into an Axle Shaft.
View detail
Whoever thought of this is amazing!
I have a motorcycle in my storage room, but when I replaced it with a Kawasaki Z400→KTM 890DUKE, the storage position became very severe due to the increased length. I bought this product because it was recommended to me by a friend of mine who uses it. I was hesitant to buy Stand Mover, but I'm glad I did. I don't know if Large has been around for a long time, but whoever thought of it is amazing. The floor is concrete, so I don't have to worry about it. I think the price is high, but I can't replace it with anything else, so what can I do? View detail
Fits: HONDA CB1300SF, Others Only available for vehicles with Quantity:2pc under frame.
For stabilizing the vehicle body during operation
When working by suspending the car body with j-trip's Suspended Frame Stand, etc.
Purchased to stabilize the vehicle
Not originally intended for use, but safe to have
View detail
Challenge to recombine Rim
[How is it used?
The front wheel of the GasGas EC250 2023, which I always use for forest road touring, has become distorted and swung large, so I replaced it with a new rim. I used this Gyro Stand to build the Spoke.
How was your experience with it?
I worked with DirtFreak's You Tube as a reference while taking a swing.
It took us about two hours and we were able to correct the flare there.
The ride felt completely comfortable and I was able to replace the Rim without any problems.
The Off-road Wheels are easily distorted when used,
I felt it was important to correct Wheel distortions from time to time.
I am glad I bought the Gyro Stand and tried it myself.
View detail
Fits: KAWASAKI KLX300R, KTM 125EXC, KTM 125EXC, KTM 200EXC, KTM 250EXC, KTM 250EXC-F, KTM 300EXC, KTM 350EXC-F, KTM 360EXC, KTM 380EXC, KTM 400EXC, KTM 450EXC-F, KTM 500EXC, KTM 500EXC-F, KTM 520EXC, KTM 530EXC, KTM 530EXC, SUZUKI DR250R, SUZUKI RM85, YAMAHA DT200WR
just right
The OEMSTAND has large, stable feet, but it cannot be hooked onto a vehicle body, making it difficult to carry.
So I bought this DRC STAND.
As shown in the photo, there are front and rear joints, and one of the joints can be changed longitudinally, so a total of three joints can be used.
Husk TC125 was Just size.
View detail
Great idea!
Spoke replacement and adjustment of CUB90 and CRF250RALLY.
We used to use a dedicated STAND that had several types of stick-type shafts, but they had disappeared before we knew it. I would have liked to have had a dedicated STAND if possible, but due to budget constraints, I prepared a wooden box this time. At the same time, I also purchased a leveler from a 100-yen store. Actually, this is the first time for me to use a taper type shaft.:Pair (for Left and Right) The wheel bearing is clamped with the Spacer from the Spacer and secured with the Screw. It is very easy to use and easy to fix. The taper type does not require multiple shafts to be stored, and as long as the wheel bearing is not loose and properly seated on the rim, the taper type will center the shaft properly. I don't know how long the taper type has existed, but whoever thought of it is amazing.
At first I thought of substituting a Pipe of the same diameter as the Shaft. When I actually used this product in my work, I realized that it is one of the most convenient and necessary tools.
View detail
ChainMaintenance
For ChainMaintenance and Wheel Polishing
Very helpful.
View detail
convenient if available
Rear tires can be rotated by using a center stand or maintenance stand, but front tires are always maintained by moving the motorcycle back and forth. I have always had to move the motorcycle back and forth to maintain the front tires. This product will probably make it easier. View detail
Fits: HONDA CB1300SF, Others Only available for vehicles with Quantity:2pc under frame.
UnderFrame Stand
To OH the steering stem of RZ, we fixed it with this product and worked on it.
It would be nice if the height could be raised a little more.
View detail
better than nothing
The product will Gap depending on where it is placed. At that time, the RUBBER feet on the back will come off.
The bank angle is quite high, so even if you think you have placed it straight, it will gap.
View detail
Thanks to the inventor!
[How is it used?
2.Purchased to put a 2.3Meter Motorcycle in a 5Meter wide place.
I mean, if it weren't for this kind of product, I might have abandoned the purchase of Motorcycle...
Was the one you received as per Image?
It was as strong and well made as the Image.
How was your experience with it?
It can smoothly move a 260Kg motorcycle and is a satisfactory product.
[Points to note]
Quantity on front wheel:If you want to set and move the device, you cannot make it Smooth until you learn the hang.
Adjust the direction of the front wheels so that both rollers of the Motorcycle Mover are grounded and can turn Smoothly.
Other items that would be helpful
Depending on the shape of the Side Stand, the orientation of the Stand Mover may not be stable.
View detail
ChainMaintenance
ChainMaintenance can now be done with ease. View detail
For Chain cleaning and lubrication
Rear wheel:Even if it is placed in the middle, it gapes due to the angle of the Side Stand, and the Chain side is difficult to work on because it is angled too much.
Front wheel:Handlebar is not recommended for use by one person, as it will break off and definitely Gap.
If I could get on it, I managed to turn the Tire with one hand.
View detail