Reviews
Black Cap tightened it up.
My vehicle has a GCraft oil cooler attached to the cylinder head on the plug side, so I need a compact plug cap. I purchased a screw type plug cap and re-purchased it.
NGK's Logo was painted White by myself, it became Point and cool.
View detail
Easier to replace than I thought it would be.
The car stalled while idling and I searched the Net and found that replacing the plug cap was a solution for similar symptoms.
I think it has been effective because so far there has been no recurrence.
However, it is hard to know how much to tighten. It doesn't get hard, and it doesn't hit the Snap.
View detail
I wanted to make the Plug caps compatible with the integrated system.
I bought a used OEM ignition system and assembled it as is.
For some reason it was hard to pull the Cap out of the Plug terminal.
When I looked for a cap and resistor compatible with integrated 10KΩ, this was the only one I could find.
I have not measured the resistance of the OEMCap.
The cap resistance of the famous Honda liquid-cooled 125cc Scooter was around 10KΩ.
Probably not a problem. 。 It is actually runnable.
The Plug cap itself was assly detached from the Cable by turning it counterclockwise.
Then turn this product clockwise to incorporate it.
For some reason, OEMCable was a little long and Cap managed to be short.
JF31 has a structure that allows earth and wiring to be taken from the engine head cover.
Whether it was the effect of this or not, there was a change in acceleration when the integrated type was used.
This is a phenomenon that could not be confirmed before taking Earth from Head cover.
Plug used is CR10EK.
The Terminal, which integrates the Screw type, was purchased from POSH.
A little more Cap length would have been better.
View detail
For As Uotani!
IgniCoil is also not viable without this Type because it requires a Plug cord that is longer than NORMAL because of the relocation. Thank you for your help. View detail
For now, we replaced it with an emphasis on appearance.
I can't tell the difference in driving by the Cap alone, so I'm going to change the Others and everything else. View detail
Plug cap
While the replacement itself is easy since all you have to do is screw in the cord, I really have to wonder if it is really Large sturdy enough to screw in. (Fixed with Tie Wrap, in case you are interested) What are your thoughts on the Cap only since it was replaced at the same time as the Ignition coil? View detail
We also replaced the Ignition coil.
I replaced the plug cap along with the ignition coil.
Originally, it was an L-Type, but due to the price, I decided to go with the 120°Short Type, and it installed without any problems.
The Snap and the stable way of getting into it, without any wobble.
I think it would be cooler if the engraving of the NGK logo on the body was painted white.
View detail
Exchange together
[How is it used?
When I replaced the Ignition coil of SEROW, I also replaced the Plug cap.
The OEM Product was good, but it was expensive, so I bought this one.
I think it is highly universal because there are various shapes.
I purchased a similar shape to the OEM Product.
How was your experience with it?
Just changing the Plug cap will change the look.
It's nice to plug in the Plug without any rattle.
Rubber cap is attached to the cord side and the plug side.
I think it's Large sturdy even with water on it.
The quality is stable.
How did it compare to other products?
The OEM Product was Black, but it was faded, but I made it to the Plug cap of the Red color.
It's a little cooler.
[Points to note]
If you don't plug in the plug cord properly, it may leak from there.
Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer
View detail
I thought it was just for looks.
I bought it just for the look of it.
When the Cell is turned, the Engine starts with a powerful sound…
I feel like laughing.
It looks so much better than OEM.
I'm satisfied
View detail
I don't know which one is better.
XJR1300 with AS Uotani Full powerKit cord at Webig [In stock] I bought the Plug cap because it was a NGK cap! That's why I bought it!
The XJR1300 is made of a silicon-like rubber-like material, so I tried to match it.
I haven't installed it yet, but it's a NGK product so I'm sure it will be fine.
My only regret is the picture of WehBig.
Can we get a photo or something from Manufacturer?
I don't see why they can't get it. Don't you think it shows the incompetence of each department, including the sales staff?
I hope you'll do well. I'm counting on you.
View detail
Since the OEM Product was broken...
The OEM Product of the 125cc Motorcycle came off from the Plug and the Idling was not stable.
It feels like it is firmly plugged into the Plug and hard to pull out.
View detail
Stable NGK no problem.
It is NGK, so the sense of security is different. However, because the color is too plain, if there is a more colorful one, it is nothing to say. View detail
Parenthesis good, 120° for TZr125!
The ignition system of TZr125 was suspicious, so Ignition coil and Quantity:It purchased with Set & it installed. Installation itself was not difficult, but in the case of TZr125, it had difficulty in handling Plug cord and Cap a little in order to take up considerably more space than OEM Plug cap (it is Red and it is Parenthesis good). If it is this type of car, it is thought that the device can be done without so much trouble if the bend angle is probably the Type of 120 degrees. View detail
This is a stable NGK product.
I bought the SP Takekawa Hyper Ignition Coil because it doesn't have a Plug cap on it.
As a result, I feel that this was chosen because there are not many manufacturers who sell the stable NGK, or rather Plug cap.
I don't think there is no Hagap because I have no experience of corrosion due to wire breakage or water ingress etc. although I have been using NGK products for ignition system for a long time.
View detail
Refresh!
'11 SUPER CUB110 (JA07) It is somehow exchanged by the exchange Timing of Ignition coil. (Lol) I didn't particularly aim for the dress-up effect or anything like that, it just degraded, so I decided to change it before something happened. View detail
As long as the thing isn't broken, I'm happy!
There were no physical problems, but when I opened the box and looked at it, Crack?
I mean, it was cracked..
It looked fine and I didn't have time to install it
View detail
NGKLogo..
I bought it believing it would be better than the OEM Product I don't know how effective it is, because I put a lot of emphasis on the appearance However, the NGK stamp, which used to be white, becomes the same color as the body, and the appeal level decreases, which is a pity It is View detail
Let's choose about handling.
Basically, if there is Size of Plug, there is no particular problem, but when I made the upper bank L-Type, the handling of the code became cramped. Ignition wire can be broken even if it is too long, and if it is short it will become uneasy.
Initially I installed up and down L-Type, but as the handling of the upper bank got a bit stricter, I purchased additional T type. In the first place, let's say what type of L-Type of this Rubber Type is type I or I feel like L-Type when I call the code with the cord plug at the upper end SIDE of the extension of Plug. So T type is safe except in special handling cases. Even if it is T type it is very L letter. In the case of the resin type, I was shaping Alpha bet itself, but it was a lack of research.
Because OEM was T type when expressed with this product, we decided to L type at the bottom and T type at the top.
Easy to install here as well. The code side can connect reliably just by inserting Screw.
View detail
Attached to CUB90DX
It is a Universal Product.
I chose the one closest to OEM Shape.
In the opportunity to change Coil and Plug I also tried to use Cap as well as NGK.
It is GOOD firmly fitting in the plug.
Since the color is also Red, I get a sense of Custom.
I think that Cap alone will change, so why do not you try it?
View detail
Exchange with Ignition coil at the same time
Easy to install, just screw in the cord as the screws are cut in
There is no change in the performance that Large is bigger than OEM, but it will become Dress-up
View detail