Motorcycle Drive Sprocket / Front Sprocket Reviews

Filter

Write a review and get Webike Points!

Reviews

Drive Sprocket / Front Sprocket Clear all

SUNSTAR

29 Feb 2024

Front Sprocket

Fits: KAWASAKI Z400FX, KAWASAKI Z400FX, KAWASAKI Z1000 R Edition, KAWASAKI Z1000 R Edition, SUZUKI GSX1100F, SUZUKI GSX600F, SUZUKI GSX600F, SUZUKI GSX600F, SUZUKI GSX-R1100, SUZUKI GSX600F, SUZUKI GSX600F, SUZUKI GSX600F, KAWASAKI ZX-9R, KAWASAKI Z900SE, KAWASAKI Z900RS SE, KAWASAKI Z900RS SE, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS CAFE

Japanese Webike user

3/5

Suitable for highways, sluggish in town

The front sprocket does not loosen unless the Impact wrench is turned at the maximum Large Power to install it. From the next time, it can be turned manually.
Also, if you do not take the Bracket on the Cover of the Sprocket, the Cover will not be attached.
The Metropolitan Expressway and the Tomei Expressway are not different.
The start of the road down the road is sluggish and doesn't fit.
(Normally, up to 16T would be good.)
Quantity assuming Fuji Speed way:Set, so will try in April.
On the other hand, we plan to try 14T in Tsukuba and other areas. View detail

SUNSTAR

18 Oct 2023

Front Sprocket

Fits: SUZUKI RG400 γ, SUZUKI GSX-R750, SUZUKI SV1000, SUZUKI V-Strom650, SUZUKI SV650S, SUZUKI SV650, SUZUKI SV1000S, TRIUMPH STREET TRIPLE, TRIUMPH STREET TRIPLE, TRIUMPH DAYTONA675, TRIUMPH DAYTONA675R, TRIUMPH STREET TRIPLE R, TRIUMPH STREET TRIPLE 85, TRIUMPH STREET TRIPLE 85, TRIUMPH TIGER800XC, TRIUMPH TIGER800, TRIUMPH STREET TRIPLE R, SUZUKI DL1000 V-Strom, SUZUKI GSX-R600, SUZUKI GSR600

Japanese Webike user

3/5

For setting up a Circuit run

I purchased this for setting up a Circuit run.
Since the OEM's hinge is 17T, the Rear Sprocket also needs to be changed to a Large size. View detail

KITACO

04 Aug 2023

Front Sprocket

Fits: HONDA NSF100, HONDA LITTLE CUB, HONDA CB50, HONDA glom, HONDA SUPER CUBC125, HONDA SUPER CUBC125, HONDA DAX125, HONDA MONKEY125, HONDA MONKEY125, HONDA MONKEY125, HONDA glom, HONDA glom, HONDA CROSSCUB110(FI Vehicles), HONDA CROSSCUB110(420Conversion), HONDA CROSSCUB110(420Conversion), HONDA SUPER CUB110-PRO(FI Vehicles), HONDA SUPER CUB110PRO, HONDA SUPER CUB110(FI Vehicles), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110(420Conversion)

Japanese Webike user

3/5

Purchased to replace Driven Sprocket and Chain and 3 other items at the same time.

The standard 14T was replaced with a 15T and the Driven Sprocket was replaced with a 33.
As for Image, it looks like Drive was changed to 15.5 Ding.
The RPMs were lowered, so the fuel consumption was up 5 km.
The first gear can now be handled like a normal Motorcycle.
But as the Shop Owner said during installation.
OEM has anti-vibration Rubber, but this one does not.
He said that the running sound would change.
This is especially noticeable at low speeds. It is a clatter from toot-toot.
What do you want from a CUB?
This is what I felt most after the exchange.
Personally, I plan to return to the OEM standard 14T and 34-ding next time. View detail

DRC

22 Jun 2023

Dura Front Sprocket

Fits: KAWASAKI KDX200R (for competition), KAWASAKI KDX220R (for competition), KAWASAKI KDX250R (for competition), KAWASAKI KL250, KAWASAKI KLX250ES, KAWASAKI KLX250SR, KAWASAKI KLX300R, KAWASAKI KX250, KAWASAKI KX500, YAMAHA WR250Z, YAMAHA YZ250, KAWASAKI KDX200SR, KAWASAKI KDX220SR, KAWASAKI KDX250SR, KAWASAKI KDX200, KAWASAKI SUPER SHERPA, KAWASAKI KLX250R (for competition)

Japanese Webike user

3/5

Commonly usable

SUPER SHERPA uses 13T, dropped 1T from NORMAL.
I think Circlip was harder to put on than OEMSprocket when installed.
Also, the lack of RubberDamper seems to make the noise level a little higher, but I guess all Universal Products are like that. View detail

SUNSTAR

07 Jun 2023

Front Sprocket

Fits: HONDA VFR400R, HONDA RVF400, HONDA CBF500, HONDA CBR400RR, HONDA CB400V-S, HONDA CB400V-R, HONDA CB400SF, HONDA CB400SB, HONDA CB400FOUR, HONDA CB400 VTEC Revo, HONDA CB400 VTEC III, HONDA CB400 VTEC II, HONDA CB-1 Type2, HONDA CB400 VTEC, HONDA CB-1

Japanese Webike user

3/5

cb400sf 520for Conversion

Buy 520Chainfor Conversion on cb400sf
Lighter than OEM but felt a little heavier
Meatless would have been better. View detail

KITACO

18 May 2023

Front Sprocket

Fits: HONDA NSF100, HONDA SUPER CUBC125, HONDA SUPER CUBC125, HONDA DAX125, HONDA MONKEY125, HONDA MONKEY125, HONDA MONKEY125, HONDA glom, HONDA glom, HONDA glom, HONDA CROSSCUB110(FI Vehicles), HONDA CROSSCUB110(420Conversion), HONDA CROSSCUB110(420Conversion), HONDA SUPER CUB110-PRO(FI Vehicles), HONDA SUPER CUB110PRO, HONDA SUPER CUB110(FI Vehicles), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110, HONDA APE 100 TypeD

Japanese Webike user

3/5

I raised it from 12T to 13T and 13T to 14T.

I went from 12T to 13Th to lower the Engine RPM when driving. I went from 13T to 14T to lower the RPM a little more. Now I can cruise 60km before the engine roars even on a moped. Of course, it is only a moped when going uphill.
When I bought it, I noticed that the Washer shape is different between Takegawa and Tokico (the position of the Bolt hole and the notch to enter the Spline are reversed), so it cannot be fastened without using the Washer included in the package. View detail

XAM

27 Apr 2023

Front sprocket

Fits: KAWASAKI NINJA1000 (Z1000SX), SUZUKI DL1000 V-STROM1000, KAWASAKI KLV1000, KAWASAKI KLV1000, KAWASAKI Z1000 (water-cooled), KAWASAKI Z1000 (water-cooled), KAWASAKI Z1000 (water-cooled), KAWASAKI Z1000 (water-cooled), KAWASAKI ZX-9R, SUZUKI GSX-R1000, SUZUKI SV1000S, SUZUKI SV1000, SUZUKI DL1000 V-STROM1000

Japanese Webike user

3/5

Longing at 16T

Engine rpm at 100 km/h is 4400 rpm
It's a little high and a little hard, so I'm going to raise the number of hits and make it Long.
A little less than 4000 rpm at 100 km/h.
Fast travel is quite comfortable. View detail

KN Planning

23 Apr 2023

Sprocket

Fits: HONDA MONKEY, HONDA SUPER CUB 50, HONDA LITTLE CUB, HONDA NSR50, HONDA NSR80, HONDA NS-1, HONDA NS50F, HONDA MBX50, HONDA CRM50, HONDA CRM80, HONDA MONKEY, HONDA GORILLA, HONDA Monkey Baja, HONDA MONKEY R, HONDA MONKEY RT, HONDA DAX50, HONDA DAX70, HONDA JAZZ, HONDA MAGNA50, HONDA CHALY 50

Japanese Webike user

3/5

CUB press 50 AA01 Fi No fit ….

The Bolt was in a different position than the one originally attached.
Since the suppression plate is not included, it cannot be installed if the screw position does not match that of the installed Sprocket.
I'm still not sure if it's a product defect or a non-conformity. View detail

SUNSTAR

27 Mar 2023

Front Sprocket

Fits: HONDA CB1300ST, HONDA CB1300SB, HONDA CB1300SF, HONDA CBR1000F, HONDA VFR750F, HONDA VF1000R, HONDA CBX750F, HONDA VF750F, HONDA CB900F, HONDA CB1100, HONDA X11, HONDA CBR1100XX, HONDA X4 TypeLD, HONDA X4, HONDA CBX750F BORD'OR, HONDA VF1000F, HONDA VF1000F Intercepter, HONDA CB1100F, HONDA CB1100R, HONDA CB750F INTEGRA

Japanese Webike user

3/5

conformance check

CB1100, used in 11 years
When we changed the standard 18 to 19, we were told that the Chain hit the Case, so we had it shaved to accommodate.
Please note that this was a compatible car model, so if you are the same as us, please be careful.
The OEM speed was 60Km at 2000 RPM, but with this product and 2 less on the Rear side (37), the speed was 68Km at 2000 RPM, which was quite effective.
I am satisfied because it runs well enough and I can expect it in fuel consumption etc., although the bottom is weakened. View detail

SUNSTAR

12 Mar 2023

Front Sprocket

Fits: KAWASAKI Z900RS, KAWASAKI Z900, KAWASAKI VERSYS1000SE, KAWASAKI VERSYS1000, KAWASAKI Ninja1000, KAWASAKI Z1000R Editon, KAWASAKI Z1000, KAWASAKI ZX-9R, KAWASAKI Ninja1000

Japanese Webike user

3/5

Replaced by drivetrain Total

This is a simultaneous replacement of the front and rear Sprocket and Chain.
I think most people replace these three items at the same time, so please refer to this page.

Since it is a FrontSprocket, the appearance and weight may not be much different from OEM, but since it is made in Sunstar, there will be some Advantage.
Durability will be as outstanding as OEM since it is made of steel.

I did the replacement myself, but I thought Impact was essential for removing the old Sprocket on my model of car.
It is tightened with so much Torque that it cannot be managed by human power.
If you are not confident, it is safe to ask Shop.

And don't forget to order an OEM Parts anti-looseness washer.
This is basically non-reusable, so prepare a new one. View detail

SUNSTAR

08 Mar 2023

Front Sprocket

Fits: KAWASAKI Ninja650, KAWASAKI ER-4n, YAMAHA R1-Z, YAMAHA MT-25, YAMAHA MT-03, YAMAHA FZ400, SUZUKI WOLF250, SUZUKI RGV250Γ SP, SUZUKI TEMPTER, SUZUKI SV650, SUZUKI SV650X, SUZUKI GSR400, SUZUKI SV400S, SUZUKI SV400, SUZUKI RGV250Γ SP2, SUZUKI GSR400, SUZUKI INAZUMA400, SUZUKI RGV250Γ, SUZUKI GLADIUS650, SUZUKI GS400E

Japanese Webike user

3/5

Expecting better fuel economy when touring!

My impression after installation is that there is little difference in fuel consumption, acceleration/deceleration, etc. in town.
I haven't gone on any long-distance Touring trips yet.
I am looking forward to seeing how much it will affect fuel economy when touring since it is now about 200 to 300 rpm lower in the same speed range as before. View detail

KITACO

20 Nov 2022

Drive Sprocket (Front)

Japanese Webike user

3/5

Let's change it if we're going to Bore up! (^^ゞ

KITACO's have holes in them, so they're lightweight and provide heat protection! View detail

DRC

30 Oct 2022

Dura Front Sprocket

Fits: HONDA XR250R, HONDA XL250 DEGREE, HONDA XR250, HONDA XR250BAJA, HONDA CRF250L, HONDA CRF250L, HONDA CRF250F, HONDA CBF250, HONDA CRF250RALLY, HONDA CRF250RALLY, HONDA CRF250M, HONDA XR250MOTARD

Japanese Webike user

3/5

usually

It's heavy, but looks strong! It looks durable and will not have to be replaced for the time being. View detail

SP Takegawa

06 Oct 2022

Drive Sprocket

Fits: HONDA CB50JX-1, HONDA CRF100F, HONDA CRM50, HONDA CRM80, HONDA CY50, HONDA GROM, HONDA JAZZ, HONDA MB50, HONDA MBX50, HONDA MSX125, HONDA NS-1, HONDA NSF100, HONDA NSR50, HONDA NSR80, HONDA Solo, HONDA XE50, HONDA XE75, HONDA CROSS CUB, HONDA CROSS CUB50, HONDA CHALY 50

Japanese Webike user

3/5

Bolt is required separately for some car models

Since it is a Small Sprocket, a corresponding Bolt may be required depending on the car model.
If you can, you can use the Quantity:I would like you to keep it Set. View detail

SUNSTAR

04 Aug 2022

Front Sprocket

Fits: HONDA BENLY 50S, HONDA Ape50, HONDA Ape50 Type-D, HONDA Ape100 Type-D, HONDA Ape100 Deluxe, HONDA GORILLA, HONDA GORILLA, HONDA Dream50R, HONDA Dream50, HONDA DAX ST50, HONDA DAX ST50, HONDA DAX ST50, HONDA DAX HONDA ST70, HONDA DAX, HONDA CROSS CUB110, HONDA CRM80, HONDA CRM50, HONDA CRF80F, HONDA BENLYCD50, HONDA BENLY CL50

Japanese Webike user

3/5

self-satisfaction

Same number as OEM, so no driving experience.
Better texture than OEM
Cospa is good
This is my first MADE IN SUNSTAR product, so I expect it to be durable! View detail

SHIFT UP

14 Jul 2022

Drive Sprocket

Fits: HONDA NSF100, HONDA APE100 [Ape] TYPED, HONDA XR100, HONDA XR50, HONDA GORILLA [gorilla]., HONDA MONKEY [MONKEY]., HONDA NSF100, HONDA APE100 [Ape] TYPED, HONDA XR100, HONDA XR50, HONDA GORILLA [gorilla]., HONDA MONKEY [MONKEY].

Japan User(translated)

3/5

In play was seen and it purchased as appropriation parts to a choinori.
Although attached by bolt-on, the size of a thickness ? spline part had a being delicate difference, and there was some shakiness... (although it was also in in play [ of other Ho ]) Since shakiness was worrisome, shakiness was pressed down with the washer.
When it could do, although he wanted to put in inside, it bore on the relation top outside of the spline.
The washer was made from about 3 mm in thickness, about 26.5 mm in width, and the bore diameter of 16.2 mm.
Since it was appropriation, it was considered as such evaluation, but the thing itself is very satisfactory.
(Fuel consumption and an engine sound improved.) View detail

KITACO

14 May 2022

Front Sprocket

Japanese Webike user

3/5

Almost no change

[How is it used?
I purchased Sprocket to take it in the Short direction to compete in the CUB Race.
The OEM was 13, but we have changed it to 12, one notch lower.

How was your experience with it?
I didn't feel much of an effect, probably because the Engine was already done in the first place, and Time was almost the same.
About one gun on the Front side may not be nearly as effective for a 50cc CUB.

How did it compare to other products?
It was quite solidly made, with a meat-removal process and so on.

[Points to note]
Nothing in particular. Installation is not difficult.

Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer
The number of Chain Piece could be handled without any change. View detail