Reviews
Is good
I replaced it with a Sprocket made by the company, so I purchased it at the same time.
It is a special product, so it can be used without any modification, and it can be used in a wide range of applications.
No problem.
It does not come loose and is adequate for performance.
View detail
Installed on a WR250R
I replaced the taper bolt because it was necessary when replacing the Sprocket, but I felt that it was a little too easy to lick the tool, so I think I'll use a different bolt next time. View detail
Price is reasonable, note installation.
Price is right.
Hexagonal Wrench has a large hole, making it difficult to fasten.
It is also easy to lick.
Strong Screw lock, Locktite is properly mandatory.
With a normal screw lock, it loosened immediately.
It can be used if one is careful and
I have no other complaints.
View detail
I can use it without problems
[How is it used?
I installed it on my D Tracker 125.
In order to install DRC's Dura Sprocket, you have to replace the OEM Sprocket bolt with this Taper bolt.
Dura Sprocket
https://www.webike.net/sd/21312642/
Was the installation difficult?
All I had to do was remove the OEM and replace it.
The OEM SprocketBolt comes with a screw lock agent, so after removing the OEM, you should clean up the screw lock agent debris.
How was your experience with it?
It worked normally
I will be happy if there is no rust in the future.
View detail
It'll loosen up.
I bought this product because of the price, but the actual product is not worth the price because of the texture. But one day, my friend told me that it was loose and I checked it. I was horrified when I thought if I hadn't pointed it out and kept using it.
The lock nut works well and the smoothness of the Bolt tapered part in contact with the Sprocket is unparalleled and more than worth the price difference.
View detail
slacken (e.g. coldness, supervision)
I've heard that this product is not good and I checked mine and to my surprise it turned with my fingers, my other Wheel which is OEM has no problem at all, it seems that there are two problems, the finish of the taper part and the lock nut is not doing its job.
I thought it was a great product because it's cheap, but it doesn't connect to the Large Trouble, so let's use OEM Product.
View detail
Exclusive Design is the only way to go!
I used it to replace the Sprocket on my 2007 wr250X with less than 16,000 miles. I fixed it with Red Lock to prevent loosening and it is perfect. Drivetrain weight reduction is easy to feel! View detail
When you replace the Sprocket, you should also replace the Bolt.
This is the Tapered Nut for DRC's Dura Sprocket. wr250X needs this because the OEMSprocket fixed bolt cannot be reused because the face is flat. The Dura Sprocket can last up to 20,000 miles if you keep up with maintenance, and it's a once in a few years expense, so it's time to replace it. View detail
I use it for WR.
I switched to DRC's Sprocket and bought this Bolt set to go with it.
The nut is a lock nut, so there is no worry about it coming off at the moment.
View detail
I couldn't fit it on the CRF250L.
Can I fit a DRC Spo ROCKET before I buy it? I asked about it. Because word of mouth said it was Taper so I couldn't wear it and it was a waste of money! Of course I told them about the word of mouth. In reply this item is Large sturdy! It fits! I'm going to contact the manufacturer and ask for a picture of the product. Please send me a picture of the item and I will send it to the Manufacturer. → Please send it to me by designated courier service by cash on delivery. I've been waiting for 20 days....Moreover, they told me to remove the OEM and install it, but it was impossible for me to install it on my spare wheel. I stopped because it's a waste of time and fuel, I got an email apologizing and that's it. The products etc. are cheap and convenient to shop at, but what about this response? Minus 5 as a response to Shop rather than a product! Well, it's convenient, so I'll continue to use it, though! View detail
Taper bolts needed to fit the Sprocket
Since the KLX230R's OEMSprocket is a straight bolt Purchased to install a DRCSprocket
Quality is fine, no snags in the hand-tightening stage
The Hexagon Bolt was not easy to lick
Hang of the work hard to lick, Hexagon Bolt with a proper tool to the extent that it is held down and It is better to tighten it on the Nut side
You can have an OEM Taper bolt, but the cost performance is It's good and no doubt
View detail
I'm a bit of a wreck
I bought it for my KLX250
I use DRC's products a lot, and so does Sprocket
I felt like the OEM Bolt was getting sucky
I ordered it when I was on a side trip
View detail
I'm impressed
Includes 6 Taper bolts and lock nuts for Sprocket mounting Quantity:Set。
Now I can install the Sprocket on my WR250 It looks rustproof and a very good buy
View detail
DRC's Sprocket
I bought the DRC Sprocket so I bought it, but the Bolt is flat while the Sprocket is flat Taper, the holes are governor, Garbage, I used the OEM one as it is View detail
No problem so far
WR 250X I exchange Bolt at the same time as Sprocket exchange of 2007 year.
I am driving without trouble for now without looseness.
View detail
It is consumable parts.
Rear sprocket We exchanged at the same time when exchanging.
If this price is exchanged everything will not be regrettable.
Rigid feeling ? Fit feeling is also good.
All Quantity : Set so it's safe.
View detail
enough
OEM is too expensive when exchanging, so use this.
There is also a reputation for easy licking, but I think that work is probably only bad.
It's enough.
I have never Trouble so far.
I will keep using it for the future.
View detail
Renthal used for 48 Sprocket installation!
NORMAL's Bolt is 10 mm and Renthal 48 Duo Sprocket can not be installed, but this Bolt solves! Off car is a salvation Bolt who is supposed to think Renthal's big sprocket is cool! W View detail
With Sprocket exchange
Rear sprocket I bought it along with the exchange.
Since Bolt & Nut attached to purchased Sprocket was able to be used, this is unused but I think that it is a good good item for Cost performance.
You can also use it with other models.
View detail
It is Fu Two.
Honda's OEM Parts Number Because ordering is troublesome, I replaced it with kore.
Material is so soft as Aluminum casting.
I had to scare it when it was not working carefully.
It works well if attached, but is not suitable for frequent removal.
View detail