Reviews
DRCRear sprocketBolt nut
Bolt nut for the new Rear sprocket.
It is a dedicated product and fits well.
Since it is a component that can easily come off, inspection before driving is a Large cut.
View detail
new setup,great look,cheap fuse
Great sprocket bolt kit! The finish is slightly mat than OEM which looks awesome when paired with a new aftermarket sprocket.Great set of fasteners for replacing the stock ones. They are a little longer and the allen head used is a few sizes larger (doesn't round as easily) than the stock ones did however have to tighten them again after my first ride. After that they have stayed tight. I'm glad i bought these as they work great. Much easier to tighten without being worried about stripping the things.webike too fast,Because it is packaged very well, it is subjected to extra inspection at customs.But the shipping fee is high. View detail
Not required for all DRCSprocket
I got a DRC Sprocket separately and mistakenly thought this Bolt with Taper was a must and bought it. View detail
It felt easy to lick.
It is possible that the accuracy of the tools you are using is poor.
I found it easy to lick. I don't think I would purchase again.
View detail
No problem!
When I replaced the Sprocket, one of the Screws came off after a while, so I bought this product, which has the same DRC as the Sprocket.
So far, I have used it without any problems.
View detail
Cost-effectiveness is good enough
The price was low... and the equipment was good enough! The tightness was good. View detail
Is good
I replaced it with a Sprocket made by the company, so I purchased it at the same time.
It is a special product, so it can be used without any modification, and it can be used in a wide range of applications.
No problem.
It does not come loose and is adequate for performance.
View detail
Installed on a WR250R
I replaced the taper bolt because it was necessary when replacing the Sprocket, but I felt that it was a little too easy to lick the tool, so I think I'll use a different bolt next time. View detail
Price is reasonable, note installation.
Price is right.
Hexagonal Wrench has a large hole, making it difficult to fasten.
It is also easy to lick.
Strong Screw lock, Locktite is properly mandatory.
With a normal screw lock, it loosened immediately.
It can be used if one is careful and
I have no other complaints.
View detail
I can use it without problems
[How is it used?
I installed it on my D Tracker 125.
In order to install DRC's Dura Sprocket, you have to replace the OEM Sprocket bolt with this Taper bolt.
Dura Sprocket
https://www.webike.net/sd/21312642/
Was the installation difficult?
All I had to do was remove the OEM and replace it.
The OEM SprocketBolt comes with a screw lock agent, so after removing the OEM, you should clean up the screw lock agent debris.
How was your experience with it?
It worked normally
I will be happy if there is no rust in the future.
View detail
It'll loosen up.
I bought this product because of the price, but the actual product is not worth the price because of the texture. But one day, my friend told me that it was loose and I checked it. I was horrified when I thought if I hadn't pointed it out and kept using it.
The lock nut works well and the smoothness of the Bolt tapered part in contact with the Sprocket is unparalleled and more than worth the price difference.
View detail
slacken (e.g. coldness, supervision)
I've heard that this product is not good and I checked mine and to my surprise it turned with my fingers, my other Wheel which is OEM has no problem at all, it seems that there are two problems, the finish of the taper part and the lock nut is not doing its job.
I thought it was a great product because it's cheap, but it doesn't connect to the Large Trouble, so let's use OEM Product.
View detail
Exclusive Design is the only way to go!
I used it to replace the Sprocket on my 2007 wr250X with less than 16,000 miles. I fixed it with Red Lock to prevent loosening and it is perfect. Drivetrain weight reduction is easy to feel! View detail
When you replace the Sprocket, you should also replace the Bolt.
This is the Tapered Nut for DRC's Dura Sprocket. wr250X needs this because the OEMSprocket fixed bolt cannot be reused because the face is flat. The Dura Sprocket can last up to 20,000 miles if you keep up with maintenance, and it's a once in a few years expense, so it's time to replace it. View detail
I use it for WR.
I switched to DRC's Sprocket and bought this Bolt set to go with it.
The nut is a lock nut, so there is no worry about it coming off at the moment.
View detail
I couldn't fit it on the CRF250L.
Can I fit a DRC Spo ROCKET before I buy it? I asked about it. Because word of mouth said it was Taper so I couldn't wear it and it was a waste of money! Of course I told them about the word of mouth. In reply this item is Large sturdy! It fits! I'm going to contact the manufacturer and ask for a picture of the product. Please send me a picture of the item and I will send it to the Manufacturer. → Please send it to me by designated courier service by cash on delivery. I've been waiting for 20 days....Moreover, they told me to remove the OEM and install it, but it was impossible for me to install it on my spare wheel. I stopped because it's a waste of time and fuel, I got an email apologizing and that's it. The products etc. are cheap and convenient to shop at, but what about this response? Minus 5 as a response to Shop rather than a product! Well, it's convenient, so I'll continue to use it, though! View detail
Taper bolts needed to fit the Sprocket
Since the KLX230R's OEMSprocket is a straight bolt Purchased to install a DRCSprocket
Quality is fine, no snags in the hand-tightening stage
The Hexagon Bolt was not easy to lick
Hang of the work hard to lick, Hexagon Bolt with a proper tool to the extent that it is held down and It is better to tighten it on the Nut side
You can have an OEM Taper bolt, but the cost performance is It's good and no doubt
View detail
I'm a bit of a wreck
I bought it for my KLX250
I use DRC's products a lot, and so does Sprocket
I felt like the OEM Bolt was getting sucky
I ordered it when I was on a side trip
View detail
I'm impressed
Includes 6 Taper bolts and lock nuts for Sprocket mounting Quantity:Set。
Now I can install the Sprocket on my WR250 It looks rustproof and a very good buy
View detail
DRC's Sprocket
I bought the DRC Sprocket so I bought it, but the Bolt is flat while the Sprocket is flat Taper, the holes are governor, Garbage, I used the OEM one as it is View detail