Reviews
Fits: KAWASAKI Ninja250, KAWASAKI Z250, YAMAHA TZR50R, YAMAHA TZR50, YAMAHA TZM50R, YAMAHA TZ50, TRIUMPH TIGER1050, SUZUKI BURGMAN400, SUZUKI BURGMAN400, SUZUKI BURGMAN200, SUZUKI SKYWAVE400 burgman, SUZUKI SKYWAVE250 burgman, SUZUKI SKYWAVE250 burgman Type S, SUZUKI SKYWAVE250 burgman TypeM, SUZUKI SKYWAVE250 burgman SS, SUZUKI DR800S, KAWASAKI ELIMINATOR 125, KAWASAKI Z400, KAWASAKI Z400, KAWASAKI Z250SL
Used for city driving
It is used for city driving.
Controllable and good feeling. It is less scary even on rainy days. The price is not too expensive and I like it.
I will report again on durability.
View detail
Fits: YAMAHA XS400SP, YAMAHA XS1100, YAMAHA SR500, YAMAHA SR400, YAMAHA GX750SP, MOTOGUZZI 1000LE MANS, MOTOGUZZI 850LE MANS, MOTOGUZZI 1000SPII, BMW R80RT, BMW R80ST, BMW R80, BMW R80GS, BMW R7, BMW R65S, BMW R45, BMW R65G, BMW R100RT, BMW R100R, BMW R100RS, BMW R100GS
Replacement recommended before Carburetor setting in SR (1JR)
I am using it on a 1998 late 1JR Carburetor generation SR.
525 modified (certified modified, he also holds a Large type license) and the carburetor has been converted to FCR Carburetor Body41.
Ignition system is iron CDI + OEMCoil of the previous year for the convenience of using Crank of the previous year of 1JR.
Plugs have been replaced about 6 times in 20,000 km due to the following Setting.
In the case of SR, it is not necessary to replace it frequently because the normal RPM is not high, but 1JR does not progress in self-cleaning in town driving due to the weak spark at low RPM of the ignition system (it seems to be intentionally done so to prevent kettling), and FCR Carburetor Body41 is even more incompatible with it. If the carburetor setting is set even a little too thick, the carburetor will turn completely black after about 1000 km and will not return to normal, as shown in the picture of Plug.
Therefore, when you do a carburetor setting that involves a large change, you basically need to replace the plug.
The peripheral creepage is in the vicinity of the Idling, the insulator is in the low open area, and the center electrode is in the MJ area.
To begin with, SR is a 2Valve big single, for better or worse. Large, crude, old car." The complete warming up of the engine takes about 30 minutes in winter, or about 10 km in distance, so if you try to set the setting by focusing on the feeling of the engine after just a short ride, the engine will tend to run in a thicker direction. So, when I try to set the setting with emphasis on the feeling after a short ride, the setting tends to be in the direction of the dark and is not fixed.
I concluded that it is best to put on a new Plug and watch it burn in the end, since it does not go to a perfect fit using the AF.
So, I am replacing it before Setting, thinking that it would be easier to do after Battery ignition, but 1JR is easy to understand...right? There are times when the price fluctuates slightly, but it is helpful because it remains inexpensive as if it is the superior etc. student of prices.
View detail
Fits: HONDA VFR800F, HONDA VFR800X, HONDA CBR600RR, HONDA CBR1000RR, HONDA CBR600RR, HONDA CBR1000RR, HONDA CBR1000RR
Satisfied with cost-effectiveness as For RacingPad
I installed it on Circuit Running's CBR600RR (PC40 2011).
Speaking of brembo's racing pads, Z04, Z03 for endurance, and Z10 recently released are the standard, but they are expensive...
I chose the far cheaper RacingCompound (RC) since it is not used for Solidly's Race.
Before the replacement, it was a replacement from HRC (Honda's RaceParts) N615.
This was not a complaint, but the Quantity:30,000 yen for 1 Set for 1 Vehicle...
The bremboZ03 is a Quantity:40,000 yen for 1 Set for 1 Vehicle....
I was a bit worried about the price of the racing pad, which is less than half of the price of the racing pad, but brembo claims it is "for Race", so I was a bit nervous and had mixed expectations.
bremboRC is a CarbonCeramic system, which means it is not sintered.
Some people think that it has to be Sintered, but in conclusion, there was no problem.
Since the pad brand was changed, the disc surface was peeled with steel wool (Bonnstar) at the time of replacement.
Of course, when we replaced the pad, we also cleaned the Piston and replaced the DOT 5.1 Fluid. We finished it perfectly.
Here are my personal impressions after using it at Sports LandSUGO.
Control is good from the beginning to the back.
The μ at low temperatures is not extremely low, and there is no need to be conscious of heating to raise the temperature.
Even when the temperature rises, there is little change to BrakeTouch, which is a good impression (although it is also a new pad).
Low thermal strain, good strength of back plate
The surface of the disc becomes black due to the effect of heat and the carbon film.
The braking force of △ Full Brake is milder (less potent) than HRC/N615, and it would be easier if it bites a little more.
The amount of Dust powder on the Wheel is small, so it is expected to be more Life than HRC N615.
So I feel a slight difference in efficacy compared to the high price FOR RacePad, but it is a much higher dimension than OEM, and from the Balance of price and Brand reliability, I am glad I bought it.
Since the BrakeCost per pc driven drops to about half the cost, I can add that floating budget to the Tire cost.
View detail
Easy to use
There were not many options available for the GSX-S1000GT, but I am satisfied with the product. It is easy to adjust.
The shape of the Lever is common, but I personally would have liked the cross section to be more rounded for easier gripping.
View detail
Fits: SUZUKI TL1000R, SUZUKI SV1000S, SUZUKI SV1000, SUZUKI GSX1400, SUZUKI GSX1400Z, SUZUKI GSX1400, SUZUKI GSX1300R Hayabusa, SUZUKI BANDIT1200, SUZUKI BANDIT1200, SUZUKI DL1000 V-STROM1000, SUZUKI DL1000 V-STROM1000, SUZUKI BANDIT1250F, SUZUKI BANDIT1250
rumor that appears to be quite true (rumour)
Replacement from FoldingLever in U Canaya.
The Kanaya Lever itself is a good one, but I replaced it because it had a fall damage since I bought the body and I did not like the Straight shape very much.
In comparison to Kanaya Lever,
The gentle bend at the base of the lever allows for more freedom in where you place your fingers.
As sung in the advertisement, the lever is gently curved so that it is soft to the touch when you hold it.
Both Levers are about the same thickness.
It was like that.
As the previous reputation suggests, I think the feature of the Largeest is the gentleness of touch when you hold it.
It is truly a lever for city driving and touring.
Those who want a Solid Touch or Sporty feel will not meet with many people, so the Straight shape is better.
View detail
It can be used properly.
The texture does not feel cheap. It's also strong and stable.
When used in conjunction with the Ladder rail and placed on the Transporter, it can also be used properly as a step ladder.
STANDDecal is also easy to customize because of the variety.
View detail
Accuracy...
The hole where the pin goes in was distorted and needed to be scraped with a file. It is not a large problem with a little work, but if you don't have a file, you cannot install it. This is why the quality rating is so low. View detail
Fits: INDIAN MOTORCYCLE 1130 SCOUT, INDIAN MOTORCYCLE 1130 SCOUT BOBBER, INDIAN MOTORCYCLE 1000 SCOUT SIXTY, HUSQVARNA VITPILEN 401, HUSQVARNA VITPILEN 701, HUSQVARNA TR650 TERRA, HUSQVARNA TR650 STRADA, HUSQVARNA TE250, HUSQVARNA TE 510 CENTENNIAL, HUSQVARNA TC250, HUSQVARNA TC250, HUSQVARNA TC 510, HUSQVARNA SVARTPILEN 701, HUSQVARNA SVARTPILEN 401, HUSQVARNA SM 510R, HUSQVARNA SM 450R, HUSQVARNA SM 510R, HUSQVARNA SM 450R, HUSQVARNA SM 400R, HUSQVARNA NUDA900
I think it is a good, inexpensive product.
This is a Rear Brake Pads replacement for a 2022 Gixxer 150, note that the pad numbers are different until the 2019 model year!
https://imp.webike.net/article/636864/
To replace it, remove the pin, remove the shaft, and replace it.
The worn out pad has a pod sticking out, so a new pad will not fit in the gap, so a push-back tool is used to put it back in.
If this work is not done well, the pad will not fit, so the skill in this area depends on the person, and it is an important part, so if you don't have an earthquake, have it done at a store.
The Pad is neither good nor bad, and I continue to use SBS, which is cheap like DAYTONA's RedPad, so I guess it's a matter of preference.
View detail
Fits: HONDA VALKYRIE1500 TOURER, KAWASAKI VERSYS 650, SUZUKI GEMMA250, SUZUKI GSR250, SUZUKI GSR250F, SUZUKI GSR250S, SUZUKI GSX250R, SUZUKI INAZUMA250, SUZUKI V-STROM 250, SUZUKI IMPULSE400, SUZUKI IMPULSE400 TYPE-S, SUZUKI RF400R, SUZUKI RF400RV, SUZUKI SKYWAVE650, SUZUKI SKYWAVE650, SUZUKI GSF750, TRIUMPH STREET TRPLE675, TRIUMPH BONNEVILE800, TRIUMPH BONNEVILE865, YAMAHA CYGNUS X
It stops better than NORMAL.
It stops more than NORMALPad.
It's about half as thick.
It is easy to control and suitable for touring and winding. Considering the cost performance, it is about half the thickness, so I think it is not the most expensive one.
I'm not sure it is suitable for Circuit or Sports driving applications.
View detail
On the MVX250F.
I used it to fill the front fork with air. It's good because I can fill low pressure like 0.4 properly. View detail
Save money compared to buying at Rose!
The color stands out and gives it a custom feel, and as a manufacturer, I feel secure. I usually use OEM products, but I bought this product for fractional adjustment as well.
The quality and appearance were satisfactory.
View detail
Fits: APRILIA GTV1000 CAPONORD (03), APRILIA RST1000 FUTURA, APRILIA RSV1000R FACTORY, APRILIA RSV1000, APRILIA RSV1000, APRILIA RSV1000, APRILIA RSV4, APRILIA SL1000 FALCO, APRILIA TUONO1000, APRILIA TUONO1000, APRILIA Tuono1000R, APRILIA Tuono1000R, BMW F800GS, BMW F800GS, BMW F800R, BMW HP4, BMW S1000RR, BMW S1000RR, BMW S1000RR, BMW S1000R
Standard but high quality?
Number of links on the OEM made it easy to work without the need for a cut.
The quality is naturally fine.
View detail
Fits: KAWASAKI KR-1/S/R, KAWASAKI KLR650, KAWASAKI KLR650, KAWASAKI KLR650, KAWASAKI KR-1/S/R, KAWASAKI KLR650, KAWASAKI KLR250, KAWASAKI EN500, KAWASAKI CS250
Good accuracy
We replaced the standard with one more gun.
Acceleration is not important, so it can be used for city driving without discomfort.
I expect that the replacement will increase fuel efficiency since there will be no noise and the RPMs will be lower than before.
View detail
Convincing texture
SizeAbout 820×I bought the one of 2000mm 。
I liked the texture of the Nylon raising on the front.
When I unpacked it, there was a smell peculiar to Rubber, so I dried it in the shade for a couple of days.
I was not sure if I wanted to go with a less expensive competitor, but I am satisfied with the DAYTONA product.
View detail
Fits: YAMAHA Tricity155, YAMAHA NMAX155, HONDA CB500F, HONDA CB500X, HONDA CBR500R, YAMAHA VINO, YAMAHA MAJESTYS XC155, YAMAHA DELUXE, YAMAHA TRICITY125, YAMAHA TRICITY125ABS, YAMAHA JOG, YAMAHA TRICITY 155 ABS, YAMAHA NMAX 155, YAMAHA NMAX, YAMAHA FJR1300 A, YAMAHA FZ16, YAMAHA FJR1300 AS, SUZUKI V-STROM650, SUZUKI V-STROM650 XT, SUZUKI SV650X
I bought it as a Stock, but I replaced it as soon as possible and it works great!
I purchased it for Stock on April 6 and it was promptly replaced.
Even after replacing the battery, the cell was weak and rarely restarted from idle ring stop, so I checked the Fuse and found that the Fuse had not run out, so I checked the Plug and found that it was covered.
After the replacement, the cell runs well, and the car no longer has trouble restarting from idle ring stop.
It has about 13,000 km since I last replaced it with the same one, and I was hoping it would last a little longer, but the price is low, so it's a good thing.
View detail
Used for CRF250L
We used it to fasten X.A.M's Driven Sprocket.
The OEM is M10Bolt, so an M8 conversion Spacer is required to use this one.
The OEM tightening torque is 50 N.m, but when I tried to tighten it with the same torque, it seemed to lick, so I tightened it with a little less torque.
I wonder if you could write the stipulation Torque in the Package.
View detail
It got brighter.
Replaced Headlight Bulb on Z125PRO.
The purpose was not only to make the engine brighter, but also to reduce the load on the battery (power saving). The Z125PRO had LED lights from the beginning, so there was no need to replace the tail lamps. I thought about replacing the blinker light because it has a normal bulb in it, but I decided not to do it because the blinker relay seems to be built into the meter and it would be complicated to change it to LED. This time, I decided to replace the Headlight Bulb and the Position Lamp with LEDs, and for the Headlight, I chose this product, which was the cheapest among the Sphere Light products.
The replacement work was as simple as removing the headlight cowl and replacing the valve with the original one, and since the valve is compact, there were no problems with installation.
As for the feeling of use, the light is bright enough and feels very bright, probably because the light is whiter. I was able to drive safely at night. I was not bothered by the dispersion of the light. Unfortunately, there was not enough of an energy saving effect that I could really feel.
Compared to when we replaced the LEDValve on our ZRX1100 a few years ago, low-cost products are now on the market, and the hurdle for replacement has gone down. If you are concerned about the brightness of your lights, we recommend replacing them with LEDs.
View detail
It looks like it will fit in the stated capacity.
2.The product is up to 5L, but it seemed like a Limit at about 2.3L.
It's in there with no problem, so it's supposed to be in there as described.
It's much easier to dispose of than the previous Dan Ball box was.
View detail
Fits: KAWASAKI Ninja1000, KAWASAKI Z1000, KAWASAKI Ninja1000SX, KAWASAKI VERSYS 1000
Replacement is easy.
ninja1000 is a Quantity:Pair (for Left and Right) Remove the Upper Cowl of the BoltQuantity before Tank:Remove the 2pcs and lift it up to reveal the air cleaner box. Next, remove the screws around the box with a Phillips screwdriver and remove the lid to replace the air filter. This filter is just fit like the OEM one. View detail
Fits: HONDA CMX/REBEL 450, HONDA CB125TD, HONDA CB125T, HONDA XL600V Transalp, HONDA XL600V Transalp, HONDA VT500FT Ascot, HONDA VP750CH Custom, HONDA VL750R, HONDA VFR400Z, HONDA VF750S, HONDA VF750F, HONDA VF750C V45 Magna, HONDA VF750C V45 Magna, HONDA VF700S Sabre, HONDA VF700F Interceptor, HONDA VF700C Magna, HONDA VF700C Magna, HONDA VF500F, HONDA VF500C V30 Magna, HONDA VF400F
Brake Pads Replacement
I used VesrahResin pad for the first time and it worked well enough for city driving and touring. Although the mileage is still low, the brake squeal has stopped. I would like to check the effectiveness and the aggressiveness to the rotor in the future.
If the results are good, we would like to continue using it.
View detail