Reviews
It's not bad.
The lever position adjustment is a mechanism where the screw comes out and hits the base, so it is not possible to adjust without a tool. I would like to have a dial type adjustment like the brake lever.
The shape of the Lever is common, but I personally would have liked the cross section to be more rounded for easier gripping.
View detail
I'm just pimping...
[How is it used? Town ride
Was the one you received as per Image? It was a little different.
Was the installation difficult? Simply replace the Connector and you're done!
How was your experience with it? The light went from a light bulb color to a white light color like a White color fluorescent lamp, and the light was confirmed to be lit well even in daylight.
[Included Parts:were they on? Two Tie Wraps in Black for outdoor use
[Was there anything that disappointed you? Quantity of claws to fit into the insertion slots.:Pair (for Left and Right) Wiring is oriented in the same direction, so depending on the direction, the wiring is short and may interfere with the cowl, so care must be taken when routing the wiring.
Replacement of ▼Lamp requires removal of the exterior of the car body, No.2 long and short +Driver, M10φ? SocketLunch.
View detail
Fits: HONDA VTR1000FVTR1000F FIRESTORM, HONDA VFR800, HONDA VFR800XCROSSRUNNER 125, HONDA VFR800F
Lever of Leaning Type
Unlike the Touring type, it has a hard feel to the touch due to its angularity. View detail
Fits: BMW Monolever R 100 RT from 09/85 on, BMW Monolever R 80 from 09/85 on, BMW Monolever R 100 RS from 09/85 on, BMW Monolever R 65 from 09/85 on, BMW R 100R, BMW R 100R Mystic, BMW R 80, BMW R 80 from 09/89 on, BMW R 100GS from 09/89 on
Thanks for handling it.
[How is it used?
chirping of a small bird (Dragging at the limit of use?) Exchange due to
How was your experience with it?
no problem
Braque squeaks are cleaned and eliminated upon visual inspection of the part mold prior to ordering.
Brake Shoe had room to spare before replacement, but was replaced due to age-related deterioration.
How did it compare to other products?
Other manufacturers that I searched on the Internet said that it works, but there is a lot of dust.
[Points to note]
The Brake Shoe of R100GS is completely different between the First Model Type and the Second Type Model, so it cannot be used. (We are Second Type Model of 91 MODEL)
Brake Shoe only, Spring and its protective rubber are not included.
The finish is just a little rougher than the OEM Product that was removed.
There was a slight BALI or roughness in the areas where Spring might touch, the hole it passes through, or where it might touch Cam, so I scraped and polished it with File, just to ease my mind.
[Others]
It is nice to know that OEM Products through Dealers have more inventory than expected, even after decades of Motorcycle discontinuation, but the prices are several times higher than they used to be, perhaps including administrative costs.
Giebenrock is still selling some of 2Valve's R100 Parts! (See Germany's website) I have never imported from a private company before. I have never imported from an individual before, so I purchased from WeBig.
*I rated it in the middle because it has only been installed for a short time.
View detail
Fits: BMW Monolever R 100 RT from 09/85 on, BMW Monolever R 80 from 09/85 on, BMW Monolever R 100 RS from 09/85 on, BMW Monolever R 65 from 09/85 on, BMW R 100R, BMW R 100R Mystic, BMW R 80, BMW R 80 from 09/89 on, BMW R 100GS from 09/89 on
Glad you are selling it.
OEM Product via Dealer is nice to have in stock even decades after Motorcycle has been out of production, but the price is several times higher, perhaps including administrative costs.
I thought that Giebenrock, which still sells some parts for the 2V R100, would be more reliable than other manufacturers that I could find on the Internet, so I bought from Webig, since I have never imported from Japan.
I rated it in the middle because it has only been installed for a short time.
*The number of Parts we deal with has been reduced a lot on the Giebenrock Home page.
View detail
I think the texture is good.
[How is it used?
I replaced it and ran about 150 km.
The shape of Lever is slightly different from NORMAL, but I soon got used to it.
Was the one you received as per Image?
Almost as Image.
Clutch lever is a little cheap in the Plastic part.
Was the installation difficult?
I am a beginner and it was very easy because there was a video of the exchange on Youtube.
I think anyone with 8mm and 10mm Wrench can do it.
How was your experience with it?
It looks good because we matched the color to the Fork and Wheel!
[Included Parts:were they on?
Grease is not included, so if you don't have it, you should buy it.
[Was there anything that disappointed you?
Plastic part of Clutch is cheap.
View detail
Think in terms of replacement frequency, not Power
I don't think there is anyone who can perceive the increase in inhalation efficiency by 0.5ps at Peak with SEROW in the product description.
I'm more of a wash and reuse kind of guy, but it's a lot more work than I thought it would be.
According to the official procedure, wash with Cleaner→ wash with mild detergent→ dry for a day→ apply Oil→ wait 6 hours and when Oil settles, you can drive.
Almost two days if you follow it exactly? If I wash on Saturday morning, I won't make it in time for Touring on Sunday.
If you're the kind of person who changes filters once or twice a year, OEM replacement would be better.
I guess it's for people who want to go as fast as possible in an hour-long Race to change filters in a month, which is often run in Course.
View detail
Silencer gasket
I used it when I installed T2RACING's Silencer on Hulk's Chamber, and although the Silencer itself was confirmed to fit, the three M6 mounting pitches were different and the hole on the Flange side needed to be widened by about 0.5mm.
Gasket also naturally has a different Pitch and requires a wider hole.
Some modification may be necessary when using for chambers other than T2RACING.
It functions fine and has no exhaust leaks.
View detail
It cannot be used for Shinobi Sen Cowl (crying).
It's my fault for not checking carefully, but I bought the upper 6 push rivetsfor replacement of the front under cowl on my 2014NINJA1000, but the inside rivet size was thicker than the OEM Product and did not fit in the holes&hellip I bought this rivet for replacement for the upper 6 push rivetsfor the front under cowl of my 2014 NINJA1000.
For your information, the correct OEM Product number is 92039-0068. to
View detail
Fits: HONDA CB1300SBSP, HONDA CB1300SB, HONDA CB1100RS, HONDA CB1100EX, HONDA CB1100, HONDA CB1300ST, HONDA CB1300 SFSP, HONDA CB1300 SF
After 20,000 km
Purchased due to idling failure after full power. I am looking forward to the next Touring, but have not driven it yet. View detail
For Wiring of Race Vehicles
I purchased Wire to match Race regulation.
Wires also come in different thicknesses, and although thicker wires are fine for the drain bord and filler caps, fine places such as the split pins of Caliper cannot be wound with thicker wires, so we purchased thinner wires.
Since it is long enough to last almost a lifetime, I think it is cosmetically sound because once you buy it, you will be able to use it for quite a long time.
View detail
Oil absorption is not good
I used it to replace oil in my Ninja 1000.
It is 3.2L when not replacing Element, but it does not suck completely.
4.You said this is for 5L.
I really thought that if I smoked 4.5L I would probably get tapped out.
The only way to handle this is to add old newspapers or Dustcloth.
Think of it as the cost of the box.
These products are hit or miss, and it is better to use a reliable product.
View detail
For XSR155 is not compatible with XSR125
Lever for XSR155 cannot be used for XSR125.
I bought it thinking that it would be diverted, but it didn't work.
The shape is different
The quality of the product is good, so I'll wait for the confirmation of XSR125 application before I buy it.
View detail
Just in case.
It may not be an option, but Neck is the pricey one for this kind of thing. View detail
Cosmo
The accuracy of the Sprocket is lower than that of other companies' Sprocket. (The difference between where the Chain is stretched and where it is not is large.)
However, if you take this into consideration and Chain tension the product, I think it is a good cosmetic product.
View detail
Plug cap
I wanted Red but it was out of stock. View detail
Easy to use
It is a common Horizontal Type carrying can.
It combines all of the above:ease of use, ease of carrying, and ease of handling.
It is 10L, so the volume is not large, but that makes it light and easy to handle.
Recommended for those who do not have a carrying can or are purchasing a carrying can for the first time.
View detail
For Oil Exchange
I use it all the time when I exchange Oil.
It is not particularly good or bad.
View detail
To
I always use it when I exchange Oil.
It is convenient to dispose of waste oil easily.
View detail
Reliable Brand
Purchased due to the addition of a Large Motorcycle.
We use Chinese STAND for 125 and 400 Class Motorcycles and this one for Large Motorcycles.
With Chinese STAND, the STANDBODY is distorted by the weight of the car body when it is lifted up, but this product can be lifted up stably without any problem at all.
If I had to make a request, I would say that protective parts should be attached to the pipe that touches the ground when lifting up, otherwise the STAND will become wound wound.
View detail