Reviews
Helmet holder
Option parts for SUZUKIOEM.
Fixed Band, Bolt is Material:Stainless Steel eliminates corrosion concerns.
As an OEM Product, it seems to have been sold before Large.
It is less expensive and better than what is available in Option these days.
View detail
It's nice and casual.
I was looking for a helmet lock that was simple, small, lightweight, and unobtrusive, but I could not find one, and then I found a helmet lock that looked just right.
SimpleHelmet lock is a key type lock that is highly universal to fit on the Pipe Handlebar, just like the OEM lock of SEA BASS. (Key case is reappearing)
I purchased it immediately and installed it. It can be installed with only two HexBolts and seems to work fine as is for a short time. (Security measures are necessary when using it for long periods of time.)
The installation took a few minutes and a lot of time, worrying about the mounting position and angle, but it fit easily by the LeftMirror Holder.
It is a SEA BASSOEM Product that is light in operation, can be locked securely, and is easy to use without getting in the way. (It is SEA BASSOEM, but the texture etc. seems to be KawasakiOEM)
The Bolt and BodyReverse side of the unit is particularly prone to rust, so it is recommended to lightly cure the exterior with Chain Lube etc.
Nevertheless, I think that this workmanship with this content is the strongest cosmetically compared to other Helmet locks.
View detail
Add to handlebar of MOTOCOMPO
It can be attached anywhere with the same Pipe as the Handlebar diameter, so it is convenient if you have a NAKED or Handlebar and want to lock it for now.
The installation is a normal Hex, so if you are concerned about it, you might want to change it.
It is good for motorcyclists who don't want to carry their helmets on their motorcycles, but don't have a helmet holder or don't want to take it with them when they are in convenience areas.
View detail
Good
Well made and works fine.
Easy to install, and at this price… I am satisfied.
View detail
Inexpensive and easy to install
This product is inexpensive and easy to install. The Screws have rusted in the rain, so if you are concerned about this, recommendendation a rust inhibitor. View detail
A classic?
I can't complain about this price with this spec. and this function with ManufacturerOEM.
EPO (PV50) I think the OEM has it on the
If you're driving a Pipe Handlebar car, you're in for a non-SEA BASS car!
View detail
Cheap, but well made!
I found this Helmet holder by chance.
It's amazing how cheap they are for something so well made!
I'm thinking of buying another one.
View detail
Best in the cos. deal with M5×12mm tinkering Torx bolt
The RAN Bretta V125 doesn't have a helmet holder, so I mounted it on the Rear Carrier (φ16.5mm) with a thick Rubber. The bolt is visible from the outside, so I used M5×12mm Torx bolts. I like it, even if it is a bit cheap looking.
As you can see in the picture, if you put it on Up, Helmet will not fall down even if you open it, and it is quite easy to use.
And above all, I appreciate the low price. Highly recommended.
View detail
The definitive UniversalHelmet lock!
The Helmet is not a good place to leave your motorcycle when you are touring.
You can hang it on the Mirror, but you don't want to leave it there with the Risk, stolen or dropped!
Helmet holder is useful in such a case, but most of the models with small engine displacement volume such as Scooter and Mini bike do not have helmet holder.
To be honest, I've never seen an OEM helmet holder that is easy to use on a motorcycle with a mid-engine displacement volume or higher, because the OEM helmet holder has a weird mounting position or the keyhole is in a weird place. I've never seen an OEM helmet holder that was easy to use.
There are also Helmet holders for sale, but they come with overspecifications like a gorgeous bracket set, or on the contrary, they are so cheap...
I'm looking for a product that's as high quality as OEM, cheap, and can be installed anywhere. Is there such a selfish product ・・・・? Good news!
Do you have a problem? SUZUKI of the world will solve your problems.
This product is a ManufacturerOEMOption, but it can be installed anywhere on a 22.2Φ (same as the Handlebar length) Pipe, with Key, and it is plated and looks good, and it is cheap! This is the best Helmet lock, but not many people know about it.
We hope you will try it too.
[Was there anything that disappointed you?
The inability to hold the key in the open position.
You turn the key to open the lock, but if you press the claw part of it with your finger, it returns to the locked state.
If you push the wrong way when hooking the D-can, the nail will retract, which is frustrating (if you can tell...)
And of course, it is OEM parts of SUZUKI, so it is proudly displayed on the key. "SUZUKI" The logo of the company sits in the middle of the room.
If it is used for Motorcycle of SUZUKI, there is no problem, but when other Manufacturer diversion is done, it becomes a little uneven.
Do you have any wishes or improvements you would like to make for the Manufacturer?
The above actions (such as adding a little resistance when returning from full open)
[Do you have any products to compare it to?
Helmet lock
What made you decide to buy?
High price, with Key, and Universality
How was your experience with it?
The function is fulfilled. There is a little bit of regret, but it is acceptable because of the high cosmetic value.
Was the installation difficult?
Done in the blink of an eye (ScrewQuantity):(Just fasten with 2pc)
View detail
I didn't know OEMs could be bought so cheaply!
I'm cheap, textured and Large satisfied!
But I do have one complaint...
It would be much easier to use if the key is removed when you open it with the key...
View detail
Cost performance is high!
I wasn't expecting much at the price of about 1/3 of the After product, but the texture is surprisingly good.
It's almost 1,000 yen with a spare key.
If you don't mind the scratches, you may want to cut the rubber sheet etc. and put the Spacer on it.
View detail
Cheap but JAPAN
I changed the carrier to the same thickness as the handlebar diameter.
The helmet holder was added.
It's cheap even though it's Japanese by SEA BASS OEM parts!
You can easily move it to the Handlebar or Frame.
You can use it while finding a convenient place to use it.
View detail
The quality is good and inexpensive.
VSTROM1000 (2014) I installed it on the Handlebar Brace bar at
This is an image of the Helmet on top of the Tank.
I can't get the key out with the lock open, so I can't just hook it up a bit.
The rest is a perfect score. I think it's overpriced.
View detail
This is the OEM Option of SEA BASS CHOINORI, but it's famous for its diversion.
I know it's not a new thing to write about.
It can be installed almost anywhere with a Pipe of 22mm or more in diameter (upper limit unconfirmed).
Of course, you should avoid the danger zone of contact with something or high heat etc. while driving.
The quality is as good as the OEMs. And it's locked up tightly.
The key is Material:It's a fine one with a Plastic key head.
It's much nicer than my MotorcycleBody, which uses a duplicate key made at Home Center.
Since the head of the mounting screw turns outward depending on the angle of mounting
It's better to change to something less common, such as Torque
You may feel more secure.
If the color was available in Matte Black, I might have chosen that one.
But at this price, I can't complain about the quality.
View detail
Cost performance at its best! is
Trusted Brand SUZUKI
It's for CHOINORI
I've been taking transit vehicles for years
3 cars (BMW SKYPER, GLADIUS650, DucatiSCRAMBLER)
Thanks for your help
This time, SecondMotorcycle
For Honda REBEL250
OEM Helmet lock
It's not very user-friendly
Thank you again for your help
It's very durable
Best of all, it won't deteriorate with age
The texture is as good as it looks
It's not cheap
Large's favorite
View detail
Perfection
The position of the helmet holder on the SUPER CUB 50 is
I'm using this product on my Rear Carrier because it was too low
I'm using it painted in Black
View detail
it is convenient -- those who improve ~♪ Tandem have no finding [ useful ] mistake! -- is it ready before the time at the place which is merely likely to suit a theft (^_^;)
it is convenient -- those who improve ~♪
Tandem have no finding [ useful ] mistake!
-- is it ready before the time at the place which is merely likely to suit a theft (^_^;)
View detail