Reviews
Fits: HONDA Press Cub 50STD, YAMAHA Cygnus 125, YAMAHA Cygnus 125, SUZUKI Hustler 50, YAMAHA New Mate 90N, YAMAHA Grand Axis 90, YAMAHA Grand Axis 50, YAMAHA Grand Axis 100, YAMAHA Gear BA50S, YAMAHA Gear BA50, YAMAHA DT50, SUZUKI Vegstar 150, SUZUKI Street Magic 110 II, SUZUKI Street Magic 110, SUZUKI Wolf 50., SUZUKI Address V100, SUZUKI Address V110, KAWASAKI AR125S, HONDA Lead 100, HONDA Benly CD125T
NiceSize for a LITTLE CUB!
The L size has enough room to cover the LITTLE CUB, but not so much that it is too large to hold. This size was the right choice because it is easy to put on the body if there is enough room, and even if the handlebar is cut and put on the body, the material is not pulled by the handlebar and tension is not applied. (Blue Material is used) is cut three-dimensionally, which is also nice because it is easy to put on.
The fabric is a thin material, but there are chain keyholes on the front and rear rings, and a Nylon strap with buckle is fused to the bottom of the center to hold it in place so that the Cover will not roll up or fly away when the wind blows. Other products in the same price range only come with a Nylon strap with buckle. (Not fused) Many of them have no way to fix them in the first place. It is very convenient to have a fusion-fitted buckle, so a buckle in this price range is very valuable.
In the initial state, the water repellency of the material surface is sufficient, and raindrops may remain on the cover as they are. With this level of effectiveness, water will not seep into the Material, so the Motorcycle will not get wet.
I don't know how durable it will be, but I keep it in direct sunlight for about half the afternoon, so we'll see how long it lasts. (We keep it under the eaves, so the rain does not directly hit it, but the rain that blows in does.)
Since it is not a heat-resistant material and the Heat Seat is not attached to the inside, it will probably melt if the Exhaust System is covered while it is hot, so be sure to cover it after it has cooled down sufficiently.
View detail
Fits: YAMAHA Cygnus X, KAWASAKI AR50/S, YAMAHA NMAX155, HONDA LEAD125, YAMAHA CYGNUS X, YAMAHA GEAR, YAMAHA NMAX, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA GRAND AXIS, YAMAHA Axis Treat, YAMAHA AXIS 90, YAMAHA AXIS 50, YAMAHA RZ50, YAMAHA NMAX, YAMAHA BWS125(BWS), YAMAHA BWS100(BWS), YAMAHA BWS(BWS), Vespa PX 200E, Vespa LX200
I should have bought it earlier.
I have always parked my MONKEY in the corner of my carport, but since it is half-roofed, it does not get wet unless it is raining and windy, and I thought I could do without the Cover because it is troublesome, but I bought it because I could not stand the yellow sand, pollen, and the ime−ji that is increasing year by year. I bought it because I couldn't stand the guerrilla downpour that was increasing every year. I thought it would be a hassle to take them on and off, but it's not at all difficult, and above all, they are visibly more beautiful and last longer. I wish I had bought them earlier. View detail
Fits: KAWASAKI W400, HONDA CB1100, HONDA CB1100 typeI, HONDA CB1100 II, HONDA CB1100 EX, HONDA CB1100 BLACK STYLE, HONDA X11, HONDA X11, HONDA CB1000SF, HONDA CB1000SF-T2, HONDA CBR1000RR, HONDA CBX1000, HONDA CBX1000, HONDA GL1000, HONDA CBR929RR, HONDA VFR800, HONDA VFR, HONDA CB750FA, HONDA CB750FZ, HONDA CB750FB
Price is reasonable. Heat resistant pad comes in a single piece.
Car models used:TRX850 Size:3L
I have been using Y's Gear Motorcycle Covers with Repeat for almost 20 years, but was attracted to the low price and decided to give it a try.
In conclusion, I should have chosen Y's Gear even if it was expensive. The material texture is cheap, but it looks reasonable from a distance because it is black. It is a pity because I would like to put it on the back. The heat resistant pad is only one piece and does not fit my car which has two Exhaust System. I looked at the product specs again, but the quantity of the heat resistant pad is not written. However, 3L is a Large type for Vehicle, so the standard is 2 pads, right? Also, they made me choose 3L because of the fitment guarantee, but it's too big. Too bad.
View detail
Fits: KAWASAKI W400, HONDA CB1100, HONDA CB1100 typeI, HONDA CB1100 II, HONDA CB1100 EX, HONDA CB1100 BLACK STYLE, HONDA X11, HONDA X11, HONDA CB1000SF, HONDA CB1000SF-T2, HONDA CBR1000RR, HONDA CBX1000, HONDA CBX1000, HONDA GL1000, HONDA CBR929RR, HONDA VFR800, HONDA VFR, HONDA CB750FA, HONDA CB750FZ, HONDA CB750FB
DAYTONA Motorcycle CoverSIMPLE 3L Size
[How is it used?
Currently in use
How was your experience with it?
I bought it because Z1000 was available in 3L size, but it was quite large and when I put it on, it was Oversized.
It came off in a strong wind the other day, but thanks to the included fixing Belt, it did not fly anywhere.
How did it compare to other products?
Cost performance is excellent. If you choose the black color, you can expect a deterrent effect against theft at night.
[Points to note]
I think it is better to buy one size smaller than the fit depending on the type of car.
Also, if the Motorcycle is secured too tightly to prevent it from being blown away by strong winds, the Motorcycle may fall over, so use moderation.
Other items that would be helpful
Included Parts:Yes/No
Belt for fixing car body
Seal to protect the Cover from the heat of the Exhaust System
View detail
Fits: Others Universal, HONDA PCX, HONDA PCX160, HONDA LEAD50, HONDA LEAD 90, HONDA LEAD 100, HONDA LEAD110, HONDA LEAD125, HONDA Dio110, HONDA SPACY, HONDA CROSSCUB110, HONDA CT125CT110 HUNTER CUB, YAMAHA NMAX, YAMAHA NMAX155, YAMAHA CYGNUS X, YAMAHA CYGNUS Gryphus, YAMAHA Axis Treat, YAMAHA AxisZ, YAMAHA GEAR, YAMAHA BWS
CT125CT110 HUNTER CUB is small and overall questionable construction
First of all, it is difficult to determine if the product is defective.
I've used it so I guess I can't return it….
CT125CT110 HUNTER CUB with GIVI-E370 attached to the Rear Carrier.
The description is marked as corresponding.
The fabric is thinner than DAYTONA's, but I guess that's what you get for the price.
When I put it over the body of the car ….
Before and after Quantity:Pair (for Left and Right) Both are tight-fitting.
The Left Side is about 5 cm above the ground in a vertical position in the Center Stand.
Right Side is about 15 cm above the ground!
Quantity:Pair (for Left and Right) You can't fix it to get Balance.
This means that with Side Stand, the hem of the Right Side will go further up and there will be a lot of gaps.
Quantity:Pair (for Left and Right) You didn't make it the other way around?
Furthermore, on the front side, the position of the hole through which the Red-colored Chainetc. is threaded is not correct.
too far forward (Vertex) Chain cannot pass.
The tread surface of the tire, not the wheel, is to be drilled and threaded.
The back side has a hole in a normal position.
It's been a while since I grabbed a Large outlier….
Again, I can't decide if it is defective or such Spec.
Even if you could request a return and return it. It's normal." and I'm going to be charged for shipping and return to myself.
Huh, I guess I'll consult Webike if I can't….
View detail
Fits: HONDA CB223 S, HONDA AX-1, HONDA CL72, HONDA CRF125 F, HONDA CRF150 R II, HONDA CRF150 R, HONDA FTR, HONDA SL230, HONDA XR230, KAWASAKI 250TR, KAWASAKI D-TRACKER X, KAWASAKI D-TRACKER125, KAWASAKI KLX110 L, KAWASAKI KLX125, KAWASAKI KX100, KAWASAKI KX65, KAWASAKI KX85 II, KAWASAKI KX85, KAWASAKI SUPER SHERPA, KTM 125 DUKE
article of satisfaction
I bought it for MC19 for CBR250R.
Material is good, size was right.
Same as OEM Product, nothing to complain about.
View detail
Fits: HONDA CB500X, YAMAHA YZF-R6, YAMAHA YZF-R3, YAMAHA YZF-R1, YAMAHA XSR900, YAMAHA XJR400 R, YAMAHA XJR1300 L, YAMAHA XJR1300, YAMAHA XJ6 Diversion, YAMAHA MT-09 TRACER, YAMAHA MT-09, YAMAHA MT-01, YAMAHA FZ-1 FAZER, YAMAHA FZ-1, YAMAHA FJR1300 AS, YAMAHA FJR1300 A, YAMAHA FJR1300, TRIUMPH BONNEVILLE, TRIUMPH TIGER 800 XRX, SUZUKI BANDIT 1250 S
It is a little Large size.
It's a Large tightening for the Ninja 400cc. View detail
Fits: HONDA SPACY100, HONDA SPACY125, HONDA LEAD110, HONDA LEAD50, SUZUKI ADDRESS V100, SUZUKI ADDRESSV125, Vespa PESPA 125, YAMAHA AXIS 90, YAMAHA CYGNUS 125, YAMAHA CYGNUS 125SR, YAMAHA CYGNUS 125X
It's worth the price.
I was looking for something that was compatible with RearBOX, so I bought it. By the way, the RearBOX is GIVI's 32L.
The quality is in line with the price, and for motorcycle use it is quite thin and allows rainwater to pass through to a certain extent.
The Motorcycle Cover is a consumable item, though. I am looking forward to seeing how long it will last.
The fatal problem is that the buckle, which prevents the wind from blowing away, can only be stopped from the Right Side of the vehicle. I always park along the fence on the Right Side, so it is very difficult to stop the buckle.
View detail
Fits: HONDA CB400SS, HONDA CBR400F, HONDA CBX400F, HONDA CBX400F, HONDA GB400, HONDA REBEL, HONDA REBEL, HONDA CB400SF, HONDA CB400SF, HONDA CB400SB, HONDA CB400SF HYPER VTEC Revo, TRIUMPH STREET TRIPLE, TRIUMPH BONNEVILE, TRIUMPH SPEED TRIPLE S, MV AGUSTA BRUTALE750S, DUCATI M400S, DUCATI M400METALLIC, DUCATI M400DARK, DUCATI M400DARK, DUCATI M400
Cover specializing in waterproof properties
The vehicle is an 87 GSX-R1100 in a Blue empty parking lot. I bought this cover as a second cover to put over the main cover on rainy days. The fabric is like Nylon waders used for fishing. The outside seems to be durable, but the inside is like Vinyl, so it seems to be weak against heat. If you are going to cover it directly, it would be better to put the attached Seat on it or hang it after the Exhaust System is cooled down. The thickness of the cover is a little thicker than PelePera, but not very thick. The thickness of the cover is a little thicker than Pe LePera, but not very thick. The only thing that bothers me is that the size chart is not correct. It fits 3L, but it is a little too large. I think it is better to look at the size of old cars. The other thing is that the ventilation is blocked by cloth. There are 6 holes of about 1cm diameter on one side, but I don't think ventilation is working well. I think other covers are made of mesh fabric, and I think it is better to make ventilation function properly because this cover seems to be waterproof. View detail
Fits: HONDA CROSS CUB50, HONDA CROSSCUB110, HONDA CT110 HUNTER CUB125, HONDA SUPER CUB 50, HONDA SUPER CUB110, HONDA SUPER CUB 50PRO, HONDA SUPER CUB110PRO, HONDA SUPER CUB C125, HONDA Dio 110, HONDA LEAD 125, HONDA PCX 125, HONDA PCX 160, HONDA PCX ELECTRIC, HONDA ADV 150, HONDA HORNET250, HONDA HORNET600, HONDA CB 125R, HONDA CB 250R, HONDA CBR 250RR, HONDA CBR 600RR
Silver Cover!
The cover is smooth, silver, and stress-free, and the front and rear markings are clear and easy to hold.
It can be hung immediately and is not damaged by the soft inner fabric.
It looks very good. However, is the price of 7,000 yenOver balanced? Is the price reasonable in view of the current prices? I am not sure. However, the product is very good, so I have no complaints.
I also like the solid Fastener in Orange, which makes the Rear clearer, and it's a great accent. It's a good buy.
View detail
Fits: TRIUMPH STREET TRIPLE, TRIUMPH SPEED TRIPLE S, DUCATI M400S, MV AGUSTA BRUTALE750S, DUCATI M400METALLIC, DUCATI M400DARK, DUCATI M400DARK, DUCATI M400, DUCATI M400, DUCATI M400, DUCATI M620S, DUCATI M600, DUCATI M620, DUCATI 620SPORT, DUCATI MONSTER696, DUCATI M750, DUCATI M750, DUCATI SS750, DUCATI 750SS, DUCATI SS750
Size is assumed to be NORMAL
I replaced the very inexpensive Body Cover I purchased on Amazon because it was torn after about 2 years of use in an environment where it has a roof but is exposed to the sun in the west.
The thickness and texture of the Cover feels solid for the price and seems to be reasonably durable.
I think the size is just fit if it is NORMAL with nothing attached. I am wearing EnduAlans Long Screen and Tanax SeatBack, and I think it would be better if it were a bit larger. The front side does not reach down to the bottom when the Screen is up. EnduAlanes is a small size for a long screen, so it is a little bit difficult to reach the bottom with a large size screen. The back of the screen is sturdy even with the SeatBack attached, but I don't think the Top case can be used. If you are wearing various kinds of attachments, it would be better to go with a size larger. The bottom side has a drawstring so that it is sturdy even if the cover is a little too large.
I reinforced it with aluminum tape, but if it still comes off, I will take it off.
A floppy-protection belt is also included, but since the belt is not fixed to the cover, you can freely choose the position of the belt, but it takes some time to put it on.
Overall, I think the product is satisfactory enough with high cost performance.
View detail
Fits: HONDA Trenzalube 400V, HONDA XR400 Motard, HONDA XR250, HONDA XR250 Motard, HONDA XR230, HONDA XL Degree, HONDA XLR250R, HONDA XLR250BAJA, HONDA XL230, HONDA TLM220R, HONDA TL125, HONDA SL230, HONDA NC700X, HONDA FTR, DUCATI Multistrada 1200S, HONDA AX-1, HONDA CR125R, HONDA CR250R, HONDA CRM250R, CAGIVA Super City WB
It's nice and solid!
The fabric is thicker and more solid than I expected.
It will not tear even if it is caught on a slightly sharp part such as a number and pulled.
The buckle is attached in the middle of the cover, just below the engine, so it doesn't flap around or fly away even on windy days. (The Motorcycle Cover I used to use didn't have a buckle so it used to fly away...)
The holes in the front and rear are designed to allow for the passage of anti-theft chain locks, etc., so that security is also taken into consideration. The holes are relatively large, but a certain motorcycle shop Baron Red." If you want to use the lock that you get when you take delivery of your car, you will need to put the lock in at an angle. It is a bit of a hassle, but don't worry, you can use it!
I put on the Cover as soon as I get back from touring, and it is very useful because it doesn't seem to melt even though it hits the Exhaust System.
I have only been using it for a month and have not had any Large problems. I am looking forward to seeing how durable it will be.
View detail
Fits: HONDA CBR400R, SUZUKI STREET MAGIC II, SUZUKI WOLF50, SUZUKI STREET MAGIC, SUZUKI RM80LT, SUZUKI RM80, SUZUKI STREET MAGIC 110II, SUZUKI STREET MAGIC 110, SUZUKI swish, SUZUKI WOLF125, SUZUKI GN125E, SUZUKI WOLF200, SUZUKI WOLF250, SUZUKI ST250, SUZUKI NZ250, KAWASAKI Z250FT, KAWASAKI Z250FT, KAWASAKI Z250LTD, KAWASAKI Z250LTD, KAWASAKI ZXR250
Easy and high cost performance!
CBR250RR (8BK-MC51) It is used for
Size was Exactly as the car model is listed in the compatibility information.
I purchased this product because I store my motorcycle outdoors in a covered bicycle parking area and I wanted to have a little waterproof performance.
In conclusion, the waterproof performance was more than sufficient for parking bicycles in a covered bicycle parking area.
I wonder if it will stain a little if it is rained on strongly, but it will waterproof with no problem if only water is splashed on it.
View detail
Fits: YAMAHA bolt, HARLEY-DAVIDSON SPORTSTERFamily, HARLEY-DAVIDSON SOFTAILFamily, HARLEY-DAVIDSON DYNAFamily, SUZUKI BOULEVARDS50(INTRUDER800,VS800GL), SUZUKI DESPELADO800(MARAUDER800/VZ800), YAMAHA Bolt, YAMAHA DRAGSTAR1100, YAMAHA DRAGSTAR400, YAMAHA DRAGSTAR400 CLASSIC, YAMAHA XV1600 R100 ROADSTER, YAMAHA XV1700R100 ROADSTER, SUZUKI INTRUDER1400, BMW R1200C, HONDA VT400S, HONDA VT750S, HONDA SHADOW Custom, HONDA SHADOW400, HONDA SHADOW750, HONDA STEED400
I use this Type from Y's Gear on every Motorcycle!
This cover is a domestic product, and I have always used this type of cover from Y's Gear, including my previous motorcycles, and this is the third one of different shapes that I have purchased.
This type is not Completely WaterproofSpec. but it is designed to be used in the event of heavy rainfall, where some rainwater will soak into the MotorcycleBody. (3rd photo) I buy knowing that.
one-eyed:Kawasaki Ninja 400 => The size of the cover was a little too large. (Maybe I got the Size wrong) The wind was blowing, the Cover was flapping, and the corners of Henry beguine's synthetic leather SeatBack were rubbed and sore. (5th photo) I think it is better to protect the attachment of soft material with Towel or something and cover it with Cover. I think it is probably due to the flapping caused by the wind.
The second:Imported 750cc => Almost ExactSize for three whole years and still in use, no tears in Cover, with Hole. I think it is an excellent product. During the rainy season, the inside of the MeterGlass fogged up once when I left the Cover on and the motorcycle steamed up, but it was fixed by removing the Cover and drying naturally. I think it is inevitable when storing outdoors.
third (e.g. in a series) (Item purchased this time):Yamaha Bolt => Almost ExactSize and will last as long as the second one. Leather Tool case with 100size, for human head, WaterproofShowerCap (3rd photo) and then this Cover is applied over it.
I think it fulfills its role as a Motorcycle Cover well.
When outdoors, I use the Covers because I think they are more dust-proof and also provide some security measures than storing the motorcycles bare.
Our Motorcycle Placement (Outdoor) The building is not exposed to direct sunlight until late afternoon. It also has a roof that is about the size of an eave, and depending on the direction of the wind, it can also keep out direct rain. Therefore, the Motorcycle Cover may have lasted for a long time.
As noted in the notes, the heat of the Engine and Exhaust System is allowed to cool before applying the Cover.
View detail
Fits: SUZUKI BOULE VARD 400, KAWASAKI ZX-14R, SUZUKI GSX-R600, SUZUKI GSX-R600, SUZUKI GSX-R600, SUZUKI GSX-R600, SUZUKI XN85TURBO, SUZUKI GS650G, SUZUKI GSX-R750SPR, SUZUKI GSX-R750W, SUZUKI GSX-R750R, SUZUKI GSX-R750, SUZUKI GSX-R750, SUZUKI GSX-R750, SUZUKI GSX-R750, SUZUKI GSX-R750, SUZUKI GSX750RR, SUZUKI GSX750R, DUCATI M1200, DUCATI DIAVEL CARBON FL
Black cover
The Cover I was using was getting old, so I was looking for a new one, and I bought this one because the ratings were not bad and the price was not that high.
Black looks good. Functionally, it is normal and usable.
The Seat that comes with the product is attached to a place near the Exhaust System where it comes in contact with the Exhaust System. I wonder what it is….
How many years will it last durably?
We will use it and see how it goes.
View detail
Fits: HONDA VFR1200X, YAMAHA XT1200Z, YAMAHA XT1200ZE, SUZUKI V-STROM1000, SUZUKI V-STROM1000XT, SUZUKI V-STROM1000, HONDA NC750X LD, BMW R1250GS, YAMAHA XT1200Z SUPER TENERE, KAWASAKI VERSYS, SUZUKI V-STROM1050, SUZUKI V-STROM1050XT, HONDA NC750X, HONDA NC750X LD, HONDA NC750X, HONDA NC750S, HONDA NC750S, TRIUMPH TIGER1050, YAMAHA TENERE700, YAMAHA MT-09TRACER
Good product, but beware of Size
[How is it used?
I've been using DAYTONA's Cover itself for many years and this is the third time I've purchased it.
I am using GIVIFitting+GIVI B37 BALDE on NC750X (RH09).
The Adventure-specific TopBOX installation type is Large, so the NC750X can be completely covered without any problem.
How was your experience with it?
It's a good product and the one I bought before lasted over 5 years, even with it covered in a typhoon.
The Adventure exclusive comes with a Screen Cover, which is a modest addition.
[Points to note]
The problem is WRLight's TopBOX installed for Vehicle's DAYTONA compatibility chart.
According to the compatibility chart, the WRLight 3L is compatible with NC750X after 2014, but the 3L is too tight and the height is too short. By the way, even with the top box removed, the front side is too short and the tire protrudes.
Large sturdy if dedicated to Adventure.
[Opinions and requests to Manufacturer
When I contacted Daytona, they replied that they had not checked the NC750X and that it was too tight in terms of vehicle dimensions, so I should use Adventure only instead of WRLight's 3L (actually, I received a polite written reply, but the content is the same). (Lol) (e.g. "I'll be back")
…The conformity chart is meaningless, DAYTONA.
View detail
Fits: YAMAHA FZR250, DUCATI 749, DUCATI 748, DUCATI 748SPS, KAWASAKI ESTRELLARS, TRIUMPH DAYTONA675, MV AGUSTA BRUTALE-S, DUCATI 748SP, DUCATI 748S, DUCATI 748RS, DUCATI 748R, KAWASAKI ESTRELLARS LIMITED EDITION, DUCATI 749S, DUCATI 749R, KAWASAKI ELIMINATOR 125, DUCATI STREETFIGHTER848, DUCATI 1299, DUCATI STREETFIGHTER, DUCATI STREETFIGHTER S, DUCATI 1098
2nd purchase
[How is it used? There is no problem. center belt, front and back, has a hole to put wire through.
How was your experience with it? It is durable, but due to the windy conditions in the area where we live and the fact that it is stored outdoors without a roof, it is likely that it will need to be replaced every few years.
How did it compare to other products? I feel it is strong.
[Points to note] If you want to continue to use the product without replacing it in a few years, you may want to consider a product on the top ranking. In my case, I had to replace it after about 15 months of use.
View detail
Fits: その他 , YAMAHA MT-09, YAMAHA NMAX, HONDA XR50Motard, HONDA NSRMini, SUZUKI GSX-R125, SUZUKI GSX-R125, SUZUKI GS125 KATANA, SUZUKI GN125E, SUZUKI RGV250γ SP, SUZUKI Gixxer 150., KAWASAKI Z250FT, SUZUKI RGV250γ-SPII, SUZUKI RGV250γ-SP, SUZUKI RGV250γ, SUZUKI RGV250γ, SUZUKI RG250 γ, SUZUKI RG250 γ, SUZUKI RG250 γ, SUZUKI NZ250S
I am using it for the Hunter Curve.
Since the product is thin, light and compact, it is easy to install and dismantle, so I use it without any burden. The water resistance is good, but because of the compact size, there are cases where all exposed parts on the left and right are exposed to rain, but it seems to be better than having a full cover and not drying out so it is full of moisture. I recommend it. -------------------------------------------------- -------- The product is thin, light, and compact, so it is easy to install and dismantle, so it is easy to use. It is waterproof, but because of its compact size, all of the parts that turn left and right are right, but it is better than the moisture because it does not dry with the full cover. I recommend it. Powered by Google Translator View detail
Fits: YAMAHA WR250X, YAMAHA WR250R, YAMAHA XJR400RII, YAMAHA DIVERSION, YAMAHA XJR400R, YAMAHA XJR400R, YAMAHA XJR400S, YAMAHA XJ400ZE, YAMAHA XJR400, YAMAHA XJ400Z, YAMAHA XJ400ZS, YAMAHA XJ400D, YAMAHA XJ400S, YAMAHA XJ400, YAMAHA SR400, YAMAHA FZR400RR-SP, YAMAHA FZR400RR, YAMAHA FZR400, YAMAHA FZR400R, YAMAHA FZR400
It's thin, but if you consider it consumable ….
[How is it used?
Use completely under Blue sky without roof
Was the one you received as per Image?
The shape is as shown in the Image, but it is thin and unreliable. It is a pity that the chain hole in the back is not colored and is black.
I used to use a 3L size with the company's WaterRegisterntLight as per Z650's fit, but this time I bought a LL because it was so large that it was almost touching the ground. This time I bought LL because it was too large to touch the ground.
How was your experience with it?
I don't know yet, but I am concerned about the durability because of its thinness. The fixed belt is difficult to use.
How did it compare to other products?
I used to use the company's WaterRegisterntLight, but the thickness of the fabric is thinner and less reliable than that. The Belt is designed to be fastened around the body so that the user does not have to bend down, but since the Belt itself is not fixed to the Cover, it is difficult to use, but this cannot be helped from a cost standpoint. The previous cover also ripped after a year, so if it lasts for a year, it may be a Merit in terms of cost.
View detail
Fits: YAMAHA X-MAX, KAWASAKI W800 Street, KAWASAKI KDX 250, KAWASAKI KDX 220, BMW F650GS, BMW F700GS, BMW F800R, KTM 125DUKE, KTM 200DUKE, KTM 390DUKE, KTM 690DUKE, APRILIA SX125, APRILIA RX125, HUSQVARNA SVARTPILEN401, HUSQVARNA SVARTPILEN701, KAWASAKI Versys 250, KAWASAKI KLX 110L, KAWASAKI KLX 125, KAWASAKI KLX 250, KAWASAKI KLX SR
I bought a new car and I bought a REITO MCP High specCover.
When I bought my second son's used CBR250RR, I arranged for a seat cover made by the same manufacturer and used it.
The price was slightly higher, but the performance, texture, and Size were not bad, so we arranged for a Repeat of the same product for a different car model.
When I purchased my second son, it was the end of last year, and as for the situation after 3 months, even though he has been exposed to some UV rays, the degree of deterioration has not been as bad as it could have been.
I believe that my purchase will be safe to use as well, as it has been used with little or no problems.
I appreciate that the back of my Seat is black, so it is easy to distinguish it from my son's. I also appreciate that the back of my Seat is black, so it is easy to distinguish it from my son's.
View detail