Reviews
A bit sorry
I tried to install a RAM Mount with this on a 12mm diameter bar.
When I tried to apply it, it was 13mm, so it was loose and turned.
I tried shaving the gap to accommodate 12mm, but no matter how much I tightened it, it still slipped and rotated and could not be fixed.
I tried to put double-sided tape on the Pipe to hold it in place, but the entire Tape kept spinning.
I gave up at this point. I'll think of another use for it; I wish the inside of the Spacer was a soft Material.
View detail
Defective product?
When I extended the Rubber to attach the product I received to my phone, it snapped.
I was totally unused, so I'm Bigly surprised at this result.
Is it due to the aging of the Rubber or the Rubber Material itself?
Anyway, I am sorry.
View detail
Fits: YAMAHA YZF-R3, SUZUKI GSX250R, YAMAHA YZF-R25, KAWASAKI Ninja250SL, HONDA CBR650F, KAWASAKI Ninja250, HONDA CBR250R, HONDA CBR400R, HONDA CBR150R, HONDA CBR500R, YAMAHA YZF-R3
It's only a millimeter, but it's a millimeter
I can compromise at worst that there is BALI or it is messy looking, but the one I have has a BallSize of 1 inch as shown in the picture. (2.54cm) It is not
It is only 1mm as per Title, but I gave up using it because it is slightly loose whether I squeeze the Arm or not.
I'm sorry
View detail
I can't charge my iPhone13pro
Although it claims to be compatible with iPhone, it does not charge the battery at all. (It becomes unchargable immediately.) If you look into it, iPhones don't support 15w charging. (up to 7, 5w) Pattern. On top of that, the Bolt that fixes the orientation of the phone does not work at all.
I checked and it is Solidly in Screw lock. (Bolt broke when I forced it to move) The battery is not rechargeable after tightening it up with a different Bolt and getting it to stay in place. This is the worst product I have ever used.
KaEdia's iPhone compatible MODEL KDR−M22A is a much better and cheaper product.
View detail
Unavailable. I think I'll throw it away.
I bought it, and when I tried to install it, I couldn't connect the Case to the Clamp. It is not fixed. I can't use it. Should I glue it or tape it? Even if I do that, I have to open the Fastener every time I take out my phone and put it in. It's a hassle. It was a product worth the price.
I will never purchase from this Manufacturer again.
View detail
It's not working
I bought it because I was worried about the phone malfunctioning, but it is obviously too soft and I think it shakes a lot while driving.
In my case, I did not install it because it is located close to the tank and it might shake and hit the tank.
It was too expensive to purchase as it was not usable.
View detail
Disappointment
I used it on my iPhone 11, but after a few dozen kilometers the image stabilizer malfunctioned and was damaged.
Maybe it was a problem with the 11 unit, but it was too fast for any number of reasons, so I will give it one star.
I have been waiting for this product for about 3 months, but just before it was released, Holder and Quantity:I was very disappointed to find out that Set's Compact Type was going to be released.
View detail
Could it be a little more Compact?
Last August, before this product came out, I installed the 3 on a CUB90 and used it with an iPhone 11. After about an hour of driving on a mountain pass (naturally with a CUB, driving at full throttle), the camera's image stabilization function completely died. I immediately replaced it with an iPhone 12, but I couldn't bring myself to use the 3 and left it alone for a while. This March, I bought this unit and am using it on my MOTO GUZZI v7 as a trial. The 3 is bulky to begin with, but now it's even bigger and looks like a waste before it's effective. I don't know about the effect on the Camera function, and I don't want to try it. Now, the body is shaking more than before, but the visibility of Navigationetc. is not a problem. I think it is possible to continue to use the iPhone11, which has a broken Camera 3 that is originally very easy to use, if only for Navigation. I am eagerly awaiting the release of a new compact model that incorporates this functionality. Good luck, DAYTONA! View detail
Is it really Large sturdy?
There is a gap between the Attachment on the back of the Case and the Locking Parts, and it is rattling.
I checked with Mr. Terasawa at the DAYTONA Customer Service Center. "Strength wise, no problem!" It was a single point of view.
With all this rattling around, I'm worried that it will be damaged while driving or that the vibration will break the Smartphone.
View detail
I want to Cancelation.
I want to Cancellation this product only. View detail
Inspection results show that the product is good.
It rotates when I mount Smartphone though there was it in Review of other people when I actually used it. It occurred even in the situation that it did not start yet immediately after installation. There was no such phenomenon when I checked the actual product at the motorcycle goods store nearby. Therefore, I asked them to inspect it. However, the result of the inspection was that it was a good product. In the end, I was told that my combination was bad. All of the parts are from the same manufacturer and the tightness of the arm is subjective, but I think it is Level without a problem. This product was originally designed to hold a smartphone in place, but it doesn't fulfill that function, yet the seller insists it is a good product. I bought this product because of its high rating, but if you see this review, I suggest you don't buy it. View detail
Are you sure you're designing it right?
The body suddenly disappeared while driving, and I was saved because I had attached a wire to prevent the body from falling. It is a pity that it is only strong from Case and rain. View detail
Fits: YAMAHA MAJESTYS, YAMAHA Majesty S
It stops opening after about a year of use.
It is good immediately after buying it. The high rating on the other Reviews probably comes from the satisfaction right after installation.
The problem is the feeling of use after one year of installation.
This product, after about a year of continuous use, the RedLever on the back will stick and you won't be able to open and close it.
This product made by DAYTONA, the usability itself is very good, so I bought the same product again after I couldn't use it once, but I couldn't use that one either due to the same phenomenon after about 1 year of use.
Again, the usability itself is very good. I'm very disappointed because if I could use it all the time I would give it 5 stars without complaint.
View detail
Cheap, but difficult to stabilize
I thought I could hold the four corners of the phone in place, but it was rattling.
There is too much rattle and I'm afraid my phone is going to fall out while driving.
I can't use the Tie Wrap without feeling like I have to.
There are also gaps at the top and bottom, but that's part of the structure. 。 But I think there are too many gaps.
If the Motorcycle is not subjected to sudden vibrations or shocks during street riding, is it barely usable?
But maybe I shouldn't complain because it's cheap.
I think it can be used if it is fixed firmly with Tie Wrap etc.
View detail
It was a difficult product.
On SC59-CBR1000RR, HURRICANE Clamp Bar was tightened with Mirror's Bolt inside the Screen, and MiKnowla's Smartphone Holder and Xperia XZ2 Premium were installed there.
However, because the power supply of the smartphone is SIDEButton, the screen sometimes disappears by vibration during Navigation, and I thought that it would go well if I replaced it with this product and bought it.
About this product
It was good point
The interference of the power supply Button etc. is avoided by making the slide part of this product Left Side.
enumeration
Bad point
I think that Spring is used for the Slide part of this product, but it is abnormally too strong and it is possible to use it with one hand.
When you try to install it, you can't get the Slide part so far that you think it will break your phone.
I have to push it and I am very unhappy
The slide part is strong to make the smart phone Quantity:The Clamp is subjected to an unreasonable force when it is set.
Since it is added, Damage is likely to appear in other Clamp Bar parts.
General review
If you attach it directly to the Bar handle, it may not be a problem even if force is applied to the Slide part. However, I think that it is necessary to pay attention to the pressure of the smart phone. The screen crack might happen?
I can't help it, I bought it, but if I could return it, I would feel like doing so.
In the end, if I want to use it, I think I have to use it by pulling Slide with my other hand while supporting this Smartphone Holder and my phone to lock and unlock it.
View detail
Fits: YAMAHA BirdCity, YAMAHA MAJESTYS, YAMAHA MT-03 (2015-), YAMAHA MT-25, YAMAHA MT03, YAMAHA Tricity155
Is it defective?
When I opened the package and checked the contents, the Silicon band attached to the Mobile Holder was on the verge of being cut off.
It's a cheap product, so I guess I'll just have to give it up as a matter of course.
It was very disappointing.
I'm not happy.
I guess it's all cheap and bad.
View detail
Fits: YAMAHA BirdCity, YAMAHA MAJESTYS, YAMAHA MT-03 (2015-), YAMAHA MT-25, YAMAHA MT03, YAMAHA Tricity155
It's broken
The part that holds the phone down broke right away
I'm not buying again
View detail
Pictures are different
Mounts that are completely different from the posted pictures will arrive (Type stopped at Belt)
If you do not like it, it is that the return fee is borne by the customer and returned.
Please be careful who you buy from now.
View detail
Fits: YAMAHA BirdCity, YAMAHA MAJESTYS, YAMAHA MT-03 (2015-), YAMAHA MT-25, YAMAHA MT03, YAMAHA Tricity155
I could not use it for my smartphone (Tears)
SYGN HOUSE's Holder that I used to use my smartphone (Xperia) Because it was LimitSize, we will replace it with the big one. However, Button which is used for ON / OFF of the screen is disturbed by the nail of Holder and it can not be used! Unfortunately it is unusable. Depending on the type of smartphone, the Button position is different, so you should check well and purchase.
View detail