Reviews
Circuit Running
I want to measure lap time in Circuit.
Purchased
I still need to know where to install the Sensor part and Wiring.
It was Large strange to pull it in.
We will verify if Time can actually be picked up properly.
View detail
Circuit Running
I bought this for a Circuit run.
As others have written, the Sensor portion of the
I am at a loss to install it.
Installation location, installation bracket, etc. are time-consuming.
It will take
You must be able to tinker with Motorcycle in a certain way.
Installation may be tough.
View detail
Sensor installation is troublesome
[How is it used?
Circuit
Was the one you received as per Image?
Image Street
Was the installation difficult?
I want to remove the sensor when driving on the street, so I need to devise a way to install it.
How was your experience with it?
Sensor installation is troublesome
View detail
In Lap timer, the Popular
After all, it is difficult to find the Sensor's mounting position.
Use is fine.
Currently, I am using Button batteries, but when inserting the batteries, the lid is incredibly hard, and I was afraid that it would break if I put any more pressure on the claw.
Also, when I bent the BodyBracket, the paint peeled off ParaPara as shown in the photo (lol).
View detail
Recommended for introductory
I used it at Tsukuba 1000 without any problem.
It is a magnetic system, so it was inevitable, but Sensor installation was the biggest problem.
The LCD may be difficult to see from some angles, but the cost performance is excellent.
View detail
Mounting position
Installed on GSX-R125 at Circuit Running.
I had a hard time finding a place to install the Sensor. I tried to install it around the Rear Suspension Link, but I am not sure if it will respond.
The thickness of the body is not so bad, so the installation space around the meter is also limited.
As others have commented, the included Magic tape is weak and insufficient, so I recommend buying it.
Convenient because it's rechargeable, and I'm satisfied with the price.
View detail
Compatible with most Circuits
When I went to run Circuit a few times, I became curious about how many seconds I was running and bought one.
The installation is easy if you are familiar with the electrical system.
The only thing that bothers me is the location of the Sensor.
Depending on the Motorcycle, it is very difficult to decide where to put the Sensor.
In the Racer's Under Cowl, the Sensor is deformed by the heat of the Exhaust System, so a little ingenuity is required.
It is very useful because it is easy to know the time.
View detail
Pay attention to the magnetic sensor mounting position and direct sunlight
First of all, the installation position of the Magnetic Sensor is troubling.
In the case of the Race car, I think it has a tight Under Cowl, so the installation position is quite restricted.
I have it over the Under Cowl around where the Side Stand was originally attached, but sometimes it misreacts …
It would be nice if the manufacturer could provide some installation examples.
Also, it stops working in direct sunlight in summer, or maybe it malfunctions? Or rather, it malfunctions?
Keep them in the shade when they are stopped.
If it's running, the wind may cool it down, but I've never had it go wrong.
Also, if you take the power supply directly from the battery, the battery will rise even if the power supply is off.
It is necessary to build a Relay or to remove the power Coupler each time (the instruction manual notes the latter).
I just bought a Lithium ion battery and the voltage was like 2V and I was shaking.
It is a mystery why there is so much dark current when it can be turned on and off.
View detail
Price suitable
I bought it to measure Time at a driving session.
I used it in Tsukuba and Mogi, and it worked fine.
The installation is bracketed to Under Cowl.
It's easy to install, so if you want to measure Time for now, this is a good introduction.
I haven't compared it to the others, so I don't really know, but it feels like the battery drains faster.
View detail
Although it is limited to the Circuit buried in magnetic bars, I bought it because of its ease of use and cost
What made you decide to buy?
I rejected the GPS-based QSTARZ and Dig spice because they are too expensive at $60,000-$40,000
The frequently driven Circuit is compatible with magnetic sensors, and it was affordable Choice
How was your experience with it?
The results of using it at three locations in the manual's "Magnetic Bar Buried Circuit List"of the instructions
Okegawa Sports Land…15cm of ground clearance is OK
However, the magnetic bar does not pass through 50 to 60cm from the end of the courseLeft, so it will not react Mm (A magnetic bar is buried a few meters from the ControlLine.)
Quick hanyu & hellip;12cm of ground clearance is not enough
They were buried a long time ago and they hardly responded
If you set up the SS at 9 cm above ground level, 80% of the time it responds, but there are many malfunctions
Tsukuba 1000…ground clearance of 18cm is OK
Only one lap of the 45 minutes was unresponsive
Was it difficult to install? (In the case of hard parts)
Be careful with the handling and fixing of Wiring to avoid the high temperature of the Exhaust pipe etc I did
Now you need some DIY skills on the Sensor side Bracket
What is the point or hang of installation (for hard parts)?
It's difficult to connect the power supply to ACC, so it's connected directly to the Battery
(After all, it's non-Waterproof, and it's removed except when running Circuit, so Large It's tough:)
The magnetic sensor is installed on the center line of the straight line with a ground clearance of about 10 cm or less in the Rider's riding condition Then it's best
How does it feel when you wear it and what is your height, weight, etc. (in the case of Apparel)? Any
[Was there anything that disappointed you?
The connector is thin and not very durable
Do you have any wishes or improvements you would like to make for the Manufacturer?
Waterproof Specification of the body
Strengthened connector part
[Do you have any products to compare it to?
The company's TimeA Tucker
[Others]
The magnetic sensor bracket is not included, so this is a DIY project
It's even better if you can use the butterfly screw to adjust the ground clearance
The magnetic sensor is covered with a plastic bag to prevent wounds and stains Waterproof
View detail
good
Purchase required for traveling Circuit. I am satisfied with the function I was looking for! I would like to improve about the point that there is no Waterproof function to Body although it has the Waterproof function of Sensor part! View detail
It is Exactly for introducing Circuit.
- Purchasing is lost with Lap timer, but it is possible to save Data with Excel and at Indicator of Orange & Green Light, purchasing this product by just making TimeAttack.
- Hang the Body on the Screen for installation. Indicator at the base of Separate handle. Sensor machines the Stainless Steel plate of 100 yen Shop and hangs it on Under Cowl. I used all the powerful Magic tape on the market. (The attached Magic tape seems weak pasting power) In addition, if you are able to do maintenance of Motorcycle, I think that you can install it without problems.
- The visibility of Body screen and Indicator is good, so you can concentrate on running.
- It is not at Completely Waterproof so you can not use it in the rain.
- Installation and handling I think that the Instruction Manual is a little easier to understand.
View detail
Cost performance is good
I purchased this product because it seems that the magnetic bar is buried in the Course that I always run and the Red external Timer seems to forget the Red outside line unit.
Easy to buy in terms of price, the function is also simple and easy to use, easy to see the Large size of the display part, it is good with the Large size which is not troubled by the installation place.
However, as far as magnetic Sensor is concerned, it will not pick up magnetism unless it is in a rather low position.
View detail
Accurate enough and inexpensive enough
Installation and accuracy
The Instruction Manual says that the Sensor is less than 20cm above the ground, but I have to use my In the case of the Suzuka TWINCircuit, which is often driven by a car, it needs to be lowered to about 11cm from the ground level to respond No. The mounting position should be lowered to the extent that it is not in contact with the ground, and the magnetism between the Sensor and the ground Lower the mounting position to a point where it is not in contact with the ground, and place the Cowletc. magnetism between the Sensor and the ground Ideally, it should be unobstructed Also, since Wiring extends from underneath the bodywork to around the meter, the exhaust pipe and Avoid hot parts of the engine and handle it in such a way that it is hard to break the wires when it falls over (Through the Cowl backing, etc.)
By the way, the accuracy of the measurement was about 0.01 seconds behind the official Circuit instrument
Quality, function and visibility
When exposed to the blazing sun for several minutes, the screen display turns completely black though it is a part that cannot be helped because of the LCD screen It becomes useless until it cools down If it starts running, it cools down with the running wind, but I try to avoid direct sunlight while waiting for running Moreover, when there is no room to look at the screen properly because Straight is short, etc., I use Back Visibility is a little difficult without light
The controls are good and the Switch is easy to press, even through Gloves
Cost performance and durability
The sensor part is currently being used for more than 2 Seasons and is exposed to mud splashes, vibration and wandering heat There is no problem However, Switch of Body has failed once To be honest, I think that the life expectancy changes greatly in how it is used, but I do not know when it falls over and breaks This is the cheapest magnetic type Lap timer of the MAJOR magnetic type I think it's a bargain
View detail
If Lap timer ZiiX
Lap timers are issued from various Manufacturers, but considering Cospa, I think the Lap timer of this LeverLight is the best.
Although I used P-LAP 3, first of all Body's Small size is good.
PLAP is not bad, but the thickness of Body will definitely get in the way.
On that point, this Lap timer is Small Type and there is nothing to worry about the installation location.
View detail
Function is enough!
While I was running Circuit, I did not have the Lap timer so far, so I only ran as much as I did so purchase to confirm Time.
I checked the operation with Mobara Circuit.
Although it is best to attach directly under the center of the vehicle, try installing the position where the Side Stand was attached. Then, by rubbing the sensor with LeftCorner.
But there is Toko that do not when you sense the porcelain bar, went on trouble position.
In the locality, I had the Bracket I had and the position to be attached was limited, so this time I installed it with Under Cowl Bracket. I was tentatively being there, so it was temporary position.
Meter itself is displayed with a large numerical value, so Time is easy to see while driving. Once the best time comes out it will be displayed as BEST once.
The function can measure only the number of laps and Time, but for me it is enough.
I do not know whether Sensor's sensitivity or porcelain bar problem, but since we often do not read porcelain, we will look at other circuits as well.
After that, I think that it is good whether the price is a bit cheaper.
View detail
StandardLap timer corresponding to various circuits
Mounting vehicle : MT-09
For running Circuit, you need Lap timer.
- Magnetic sensing type ← This product is Type
- Red external line reception formula
- GPS measurement formula
There are various methods such as
- Magnetic sensing type corresponds to Circuit nationwide
- Relatively good accuracy compared to price
⇒Red external line formula seems to be difficult to adjust the direction of the transceiver.
⇒ GPS equation becomes expensive when it obtains accuracy.
- A certain Ama ○ onetc. Though cheap Chinese-made things are sold, it is not reliable
I purchased this product from the above.
Product is Body (Display Monitor section) And the magnetic sensor part. Power supply to Body battery (CR 2032 X Quantity : 2pc. Set) or vehicle 12V withdrawal. Since I want to check Time to detach it after driving and move it with a battery. It seems to have about 10 hours.
Note that Memory of Time can be up to 999 LAP, but Data Extraction (USB or SDCard) Because it is impossible, I'm dedicating to Excel by 1 LAP each time by hand (^^;)
Also, interval Time can not be measured.
Sensor installation location is limited,
- Road surface (Embedded magnet) Set within 15 cm from
- There is no Gold genus between the road surface and the sensor (Resins are OK)
- It is desirable to set it in the middle of Tire
Therefore, depending on the vehicle it will have difficulty in the installation position.
In the case of MT - 09, considering the above limitation, there are not many choices of installation sites, I installed the Side stands switch Bolt (M5) Extended, Bracket attached from the back and fixed. Because it is a self-propelled group, it is fixed only with Circuit, so the butterfly screw is stopped, but it does not loosen at all (Just to be sure, we check each run). But even at this position Clearance with the road surface is quite severe, once I exchanged the Tire pressure and made a full bank I rubbed a bit - - - I did not break down. I have no choice but to make fine adjustments
Functional aspects are satisfied as minimum lap time measurement can be done with reasonable precision. However, if you look at the price made in China, I think that it will be a little cheaper (At least ten thousand yen will expire). In that respect, we made it four ☆.
View detail
[Webike Monitor] If the main part is waterproof specification, I think that it was better. Very easy only by making it connect and crawl on one Cable, if attachment is only a battery. The Time came to be found in a Real time, and interest in
[Webike Monitor] If the
main part is waterproof specification, I think that it was better.
Very easy only by making it connect and crawl on one Cable, if
attachment is only a battery.
The
Time came to be found in a Real time, and interest increased to the run.
View detail
Although purchased in response to introduction for to realize each other with if you to have no Timer although it goes to a Circuit by a JADE to play, it is satisfactory in general. It is good to read the Lap time and to make it in a csv File. Thou
Although purchased in response to introduction for to realize each other with if you to have no Timer although it goes to a Circuit by a JADE to play, it is satisfactory in general.
It is good to read the
Lap time and to make it in a csv File.
Though it is simple that it can access as a read-only File when it ties to
USB charge and PC, there is no futility.
They will be five stars if it further succeeds in the measure to
water proof.
View detail
A ZiiX Time attacker price is cheap, and it has the function needed enough. Since it is Battery attachment, if an optional Sensor is attached to another Motorcycle, it is convenient to use by two Motorcycle, sharing the main part of Coun
A ZiiX Time attacker
price is cheap, and it has the function needed enough.
Since it is
Battery attachment, if an optional Sensor is attached to another Motorcycle, it is convenient to use by two Motorcycle, sharing the main part of
Counter.
It excels in the Cost performance very much.
View detail