Reviews
Weak rigidity of the bar
I installed it on my 2nd model MT09SP, but it is a large size because it interferes with the controller of the rear suspension. The bar is not rigid, so when the back is attached, it bends inward, so I have to check the interference with the tire every time I attach it. View detail
Unfortunately, the length was good but the shaking while driving was not calculated.
Since the Meter on MT-07 is directly above the Handlebar, I wanted to place my phone and Car Play Monitor on the upper side of the Meter, so I chose this product with a longer bar length.
The length was good, but the Mirror mount bracket was not able to support the weight of the phone and CarPlay Monitor due to the Bolt1 pc fastening, causing it to shake considerably while riding. As a result, I moved the length of the bar to a shorter length so that it would be closer to the fulcrum. Since it still shakes, I am planning to change to a Bolt2-Bolt Type of Master CylinderClamp from DAYTONA and others.
View detail
The explanation is hard to understand for an OEM Product.
It's OEM, so the length is nice. However, the schematic of the pullout did not show the location of the Controller, and I noticed it when I was looking at Motorcycle's undercarriage. I wanted it to be a picture at least. There are many kinds of bundle wire Band, but they are too thick to fix the Harness and cannot be used as instructed. View detail
It didn't work. (My mistake)
My AF24TACT with AF34LIVE DIO carburetor installed. (This product) The diameter of the lens was just a little too small. The diameter did not fit and I could not install it even though I tried to modify it and force it to fit. It is a pity because it is very cool. It is my mistake that I bought it without checking it carefully. View detail
It's well made, but....
Installed on High ace3 late model, WideMiddle roof car.
It looks and feels solid, but I can't get the Hook to work.
I had no choice but to use Tie Down's Sub belt.
View detail
Fits: HONDA CB1300SF, Others Only available for vehicles with Quantity:2pc under frame.
UnderFrame Stand
To OH the steering stem of RZ, we fixed it with this product and worked on it.
It would be nice if the height could be raised a little more.
View detail
Easy to insert into Fork
When inserting the STAND into the front fork hole, the STAND tip bracket is inserted at an angle,
It is a little hard to get into the holes. Once it is up, it is fixed perfectly, but it takes a lot of time to insert it into the two Fork holes.
View detail
The product is good, but..,
The quality of the product is very good, as it is made in Japan. However, the contents of the package, especially the tires and other components, smelled like cigarettes and filled the storage room. It is a pity because the product is so good. View detail
It was a little long for me.
[How is it used?
After six months of hanghang and Restore&Custom work on the LITTLE CUB, I thought I'd get comfortable with the next stage of the project. First, we need an external power source. I started looking for a USB power supply, but realized that there was no place to install them, so I looked for a Mount Bar in Webike's product introduction section and bought a Multi Bar from Made by HURRICANE, which had a safe design.
How did you like it?
Although I knew it existed until now Messy around the Handlebar. The Mount bar had never been used before because I had the impression that it was too heavy.
The fact that I had a safe length and design for my first Mount bar purchase and I was a teenager. Separate handle (Handlebar of Separate type)". Speaking of Other Brand Products of "HURRICANE It was an Image that I was not surprised to see. Finally, I too will buy HURRICANE products." I bought the Multi Bar at Tension...but the bar was a little too long for my use.
Please don't get me wrong, the product itself was a good product with good rigidity, but for my personal use, I would have preferred a shorter length, so after much thought, I replaced it with a Mount bar made by another company.
We wanted to use a Short Type Mount Bar to make it as Refreshing as possible, since we only need to be able to fix the USB power supply and Smartphone Holder.
How did it compare to other products?
If it is a MAJOR Manufacturer's product. "A damned glitchy piece of junk." I don't think there are any.
Before you buy Which car? of Which part? and there you want to install it in What do you want to install?" I think that Risk can be reduced if you take into account the following before making a purchase.
[Points to note]
This product is a type that is attached to the Mirror Holder by fastening it to the Mirror Holder, so it is easy to set the quantity to a position that is easy to use.:Once set, please tighten and secure each part firmly, otherwise you will be in a hurry if it loosens while driving... (This is a testimonial.)
Other items that would be helpful
The deciding factor in the purchase
As I mentioned above, I didn't even understand the difference between the Mount bar and I didn't think it through. HURRICANE Products I bought this product only because it was a very solid product with no fault of this product over and over again.
【Included Parts:presence or absence】.
Bracket for connecting Mount Bar Body and Mirror Holder, 2 Washers and Spring washerQuantity:1pc. and Nut included.
[ITEMS TO BUY TOGETHER
Products to be installed on Mount bar.
If you purchase the products you want to install at the same time, such as a power supply outlet, Smartphone Holder, Drink Holder, Camera Mounting Holders, etc., you can proceed with the work at a stretch.
Opinions and requests to Manufacturer.
It resonates with my father's generation. "HURRICANE BrandName, we look forward to continuing to serve you with a variety of custom parts at affordable prices.
View detail
Fits: YAMAHA WR250X, YAMAHA WR250R, YAMAHA XJR400RII, YAMAHA DIVERSION, YAMAHA XJR400R, YAMAHA XJR400R, YAMAHA XJR400S, YAMAHA XJ400ZE, YAMAHA XJR400, YAMAHA XJ400Z, YAMAHA XJ400ZS, YAMAHA XJ400D, YAMAHA XJ400S, YAMAHA XJ400, YAMAHA SR400, YAMAHA FZR400RR-SP, YAMAHA FZR400RR, YAMAHA FZR400, YAMAHA FZR400R, YAMAHA FZR400
A little short.
I selected it from the vehicle compatibility chart, but the Rear is covered well, but the Front is not covered enough. I can compromise because I use it in a covered parking lot, but it is hard to lock the chain lock. It was a little more.
The texture of the Cover is good. As mentioned above, it is roofed, so I don't think it will be water repellent or strong, but I think it will keep for a long time.
View detail
parts shortage
The product was very well made, but the screws to attach the top case were not included. View detail
better than nothing
The product will Gap depending on where it is placed. At that time, the RUBBER feet on the back will come off.
The bank angle is quite high, so even if you think you have placed it straight, it will gap.
View detail
Maintenance essentials
Maintenance necessities including Torque management
I have been stingy and gathered information on the web etc., but considering the accuracy of the information and the time involved, it is better to purchase.
I should have bought it earlier.
View detail
Your Edia Sun visor
Purchased as a countermeasure against thermal runaway in the summer and against not being able to see when the sun shines.
Since the purchase was made in December, I guess we will have to wait until next year to see the effect.
View detail
Fits: Others AIO-5 Lite
Neither good nor bad
Installed at the same time as SMARTRideMonitorSRS-001.
Or rather, it is a product with Monitor.
To install, simply screw it into the Valve cap.
There is nothing difficult to do.
The Monitor displays Tire air pressure and temperature.
A warning will be displayed if the pressure is less than the set pressure value/Large.
To be honest, the TPMS I used to use has more functionality than that, such as being able to set air pressure in the front and rear Tire and check it on my phone.
Well, since we have SMARTRideMonitor, I will use this one.
View detail
Fits: YAMAHA ZEAL, YAMAHA TRZ250, YAMAHA SR400, YAMAHA R1-Z, YAMAHA BWS125, SUZUKI GRASS TRACKER, SUZUKI GSX400, SUZUKI VanVan200, SUZUKI ST250, SUZUKI RGV-y250, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR400, KAWASAKI ZRX400, KAWASAKI Ninja250R, KAWASAKI Estrella, KAWASAKI BALIUS, KAWASAKI 250TR, HONDA HORNET, HONDA JADE, HONDA NSR250
Buy for Motorcycle
I bought this for my wife's electric mothers' bicycle, and the size could have been a little larger. The handlebar is raised because it's for a motorcycle. View detail
Bolt hole
Since the Bolt hole position was different by about 5mm and could not be installed, it was installed by making a long hole with File. Forced installation may damage the screw holes. View detail
Fits: Others TOYOTA 200 Series High ace
Leather suit is heavy
I am doing Road race and may open Rear hatch and put on Leather suit.
In my Leather suit, the Hatch comes down, so I added this Stopper to prevent this.
View detail
Additional thermal protection for Motorcycle Cover
I bought a DAYTONAMotorcycle Cover. the Heat Seat is attached on the back side, but the exhaust pipe part was not attached and melted. i repaired it and put the Heat Seat on the back side. View detail
Fits: SUZUKI V-Strom 800 DE
I installed it.
[How is it used?
DL1000 V-STROM800DE Black I installed it in the
Quantity:Pair (for Left and Right) Side case of the
Was the one you received as per Image?
The black color matches the Motorcycle color.
Was the installation difficult?
Installation was easy even by myself, but there was a little hang (order? I had to make a large cut.) I was able to install it easily by myself, but a little bit of hang (order? fit?) was too much.
An assembly Instruction Manual is included, but there are no instructions.
If you only looked at the diagrams in order, you had to start over.
The completed mold must be imaged and installed.
How was your experience with it?
The tight fit between the Frame and Case on the Motorcycle is not good.
From the back, the Right Side looks good, but the Left Side is very tight.
I am using this Manufacturer's stuff for the first time,
I couldn't figure out how to attach Frame and Case since it is not mentioned.
The topCase is compatible with the topCase. If a large topCase is attached, the lid of the attached case will not open.
With 45LtopCase, the Limit lid and the lid opened.
[Included Parts:were they on?
The minimum amount of screws, nuts, and washers required for installation were included.
Washers are not marked with a distinction, so we had to combine them by looking at Screw size and drawings.
Maybe a little puzzle.
Tools are not included and must be prepared by yourself.
[Was there anything that disappointed you?
As I mentioned earlier, the Left Side is difficult to fit.
It is fixed with a fixing component after it is pushed sizzling into the Frame.
View detail