Reviews
Fits: KAWASAKI Ninja 150RR, KAWASAKI Ninja 150RR
I finally found it, but...
The Disc Rotor in NORMAL is too small and the pad does not hit the entire surface.
Large Disc Rotor must be replaced.
View detail
Fits: SUZUKI Hayabusa
To prevent scratches
Like the Smartphone, I bought this to prevent scratches. I found it as difficult to apply as smoked film on a car. Of course it is effective, but I would like to know how to apply it easily and beautifully. View detail
Installation is a big deal?
Exhaust pipe and engine joint parts do not fit together because the screw and screw hole on the engine side do not match slightly, and when the two exhaust pipes, the assembly, and the exhaust system are connected first, they do not fit together with the engine exhaust. The position of the bracket to be connected to the middle frame was also not aligned as per the instruction manual. I ran about 50 km and there was no exhaust leak and low speed knocking was reduced and the sound was good. I hope the manufacturer will improve the accuracy of their products. View detail
![[HONDA x AVIREX] Tactical Daypack](https://img.webike-cdn.net/catalogue/images/79185/0SYTN-28J_03_TS.jpg)
It's more … than I thought it would be.
"Honda" I was expecting a certain amount from the words "I am a Gold", but I was satisfied that the price was right. The shoulder belt is too short and poor to adjust, so I had to adjust it almost fully extended before carrying it. The body belt and chest belt are also too short. The capacity is small due to the small number of compartments and pockets, 30?" It appears to be as indicated.
Now I'm used to it and can carry it quickly, but next time I won't buy this kind of thing, I'll go back to my old BackpackManufacturer one that prioritized functionality.
View detail
Fits: HONDA , HONDA CB500X, HONDA CBR500R, HONDA Rebel1100 DCT, HONDA CRF250RALLY S, HONDA CRF250RALLY, HONDA CBR650R, HONDA CBR400R, HONDA CB650R, HONDA CB1300SUPER FOUR SP, HONDA CB1300SUPER FOUR, HONDA CB1300SUPER BOLD'OR SP, HONDA CB1300SUPER BOLD'OR, HONDA CB1000R, HONDA 400X, HONDA Rebel1100 T, HONDA Rebel1100, HONDA CBR650R, HONDA CB650R
Nice looking sticker on the tank!!
For my 2023 Honda Rebel 1100 - very simple to apply, just makes sure alcohol wipe the surface first and then line up the stick with the gas tank. You might experience some unaligned screws holes on the sticker, in that case use a heat gun gently on it then use hand move the stick to the proper positions. Overall - nice looking products but for almost $20 I think is little over price, and not sure how long it last. View detail
Air bubbles unavoidable
I bought for 2023 Honda Rebel 1100 - The package comes with 2 set of film of both lens (round odometer and half moon shape engine light), package comes with instruction and the material of the film is good maybe too good of the thickness. (I’ll explain below), I have done film, carbon film wrapped and window tinting myself, this odometer film should be simple and easy as instruction said: 1. Alcohol wipe. 2. Peel half the back sticker and spray with water, 3. Apply to the sticker onto lens and spray water then peel off the back sticker. 4. Use a film squeegee push out the water and air within. Unfortunately, I wasted both set not able to 100% eliminate air bubble, no matter what there is at least 30% air still capture within and if you try too hard you’ll damage the film, I believe the quality of those film it’s too thick couldn’t able to squeeze properl, I even let it sat under the sun for 2 days hopefully it’ll take off the bubble it still remain the same amount… If you not looking for perfection then this might work for you, but I can’t stand the bubble ended peel them all out and threw it in trash. I think for over $15 this should be a nice and easy to use products, is not worth the money. View detail
Although inexpensive genuine leather Jackets are available ...
From a distance, it looks like a reasonable Jacket, but the details are very cheaply made. And the leather, which is claimed to be genuine leather, seems to be very thin. In general It's well-made, but thin and cheap." This is my honest impression. Kadoya. Ya "DEGNER" It should be considered as a separate product from It is not something I would recommend to anyone I know.
I want a leather jacket, even if it's simple and cheap." It would be safer to avoid them unless you are a person who is
View detail
Fits: HONDA CB300R, HONDA CB150R, HONDA Monkey125 (MONKEY125), HONDA GROM (Grom 125), HONDA CB125R, HONDA CBR250R, HONDA CB250R
Lever Replacement
A little cheap. It feels uncomfortable when your finger hits the inner groove. View detail
Fits: HONDA DJ-1, HONDA DJ-1R, HONDA DJ-1L, HONDA DJ-1RR, HONDA NSR50, HONDA NSR50, HONDA XR50 MOTARD, HONDA Express, HONDA CAREN S, HONDA GYROUP, HONDA GYROX, HONDA GYRO CANOPY, HONDA JUST, HONDA JULIO, HONDA JOY, HONDA GIORCUB, HONDA Giorno, HONDA GIORNO DX, HONDA SQUASH, HONDA SPACY50
subtle
Perhaps it is because the Scooter has a low power generation rate, but I feel that the Halogen bulb has a wider beam range and better visibility.
This might be better with a slightly better Halogen bulb.
View detail
The magnet is missing.
Installed in vehicles without an oil filter. It collects impurities with a mesh filter and magnet.
The inlet and the net filter are too close to each other, and if dirt accumulates, it will clog the filter.
The magnet is shaved and the quality is delicate.
Plating on the reverse side of the case is defective and the quality is delicate.
Well, better to have it than not to have it.
View detail
Higher height.
I bought this when the Autofocus on my previous iPhone 11Pro Camera broke.
Type VibrationControlDevice to be attached to existing Smartphone Holder3
Just Smartphone Holder3+ IH2100Rigid (25077) The pull-pull mechanism is about 20mm higher than that of the "M" and it shakes more when a smartphone is attached.
I think it can absorb a certain amount of vibration, but the increased height makes it look bad.
If I were to purchase an expensive SMARTMonitoretc. without a phone attached, I would be willing to purchase a used Android phone and use it with TetherRing.
View detail
It is hard to get through Bar End.
It is used to temporarily lengthen a handlebar that has been shortened in overall width, and when combined with the EBB301K Bar End, it returns to the Japanese Vehicle Inspection Correspondence. I was able to get it through by using a heat gun, lubricant, and a rubber hammer. I am afraid I could not pull it out, so I will keep the Bar End and this product in quantity.:It will be used in Set. It's good because it's only for car inspections…. View detail
I've been waiting over 6 months for this...
I am a New Model KATANA rider. 。 Ordered in spring, delivery delayed…. Delay…. Also delayed…. It finally arrived at the end of the year.
Now, assemble it ? But the middle of the three mounting points don't fit together. 。 I managed to attach the Right Side by enlarging the holes in the bracket to the limit, but the Left Side is not attached at all. 。 Bracket is attached to a ton of places. 。 In the end, the Firmly fixed Bracket was scraped off and the Bracket was remade and fixed and finally installed.
I heard from fellow KATANA members that A-TECH products are no good? so I wasn't too surprised.
If I returned the product with an Objection, I did not feel like making an Objection because I thought I would have to wait another year to receive the product again.
Anyway, it seems that A-TECH's Carbon parts have many Objections.
Those who order should be prepared to order.
View detail
Images alone are not good enough.
It is a compromise because it is inexpensive, but I still couldn't tell the Fit feeling from the image alone.
Size:Even though it was Free, it was a little hard on Small.
I regretted buying it.
Well, it is Point payment, so I will compromise, but I will probably not use it and keep it or give it to someone else.
I realized that I should not buy just based on images.
View detail
Fits: KAWASAKI ZZR1400, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-14R, KAWASAKI ZX-14R, KAWASAKI Z1000, KAWASAKI 1400GTR, KAWASAKI ZX-6R, KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI ZX-6R, KAWASAKI ZX-14R, KAWASAKI 1400GTR, KAWASAKI 1400GTR, KAWASAKI Z1000, KAWASAKI ZX-14R, KAWASAKI ZX-14R
Pad replacement
Normal. Good cosmetics. Large inventory. View detail
Air bubbles will be noticeable.
My first impression was that it was smaller than I had expected.
It is a little small for a Large Motorcycle, giving the impression of unbalance.
The advantage is that it is transparent and allows the best of the paint to be used, but on the other hand, air bubbles can be noticeable, so it must be properly warmed up and applied neatly.
If the angle of the tank is sharp, the edges will peel off, so you need to warm it up thoroughly and degrease it before applying it. I replaced the tank pad with another one because I was concerned about air bubbles and the shape of the smallest tank.
View detail
I think Dress-up is the main one.
[How is it used?
I installed it on a vehicle that I normally use for Race.
Was the one you received as per Image?
Yes.
Was the installation difficult?
It is easy to replace the original screws by simply loosening them with a screwdriver.
How was your experience with it?
I was told that I could turn it by hand, but with my vehicle, the hose was in the way and hard to reach&I couldn't turn it by hand.
[Included Parts:were they on?
There is none
[Was there anything that disappointed you?
Cannot be turned by hand.
It may be a good idea to purchase them as dress-up parts, but you may not want to replace them for practicality.
View detail
The product came with scratches.
As per Title, I received a scratched product. 。
The price is quite expensive, but I guess that's what you get from an outside parts company. 。 The installation method is also quite insecure, just drilling holes and screwing them in. 。 So I'm trying to figure out if I can put 3 points on Bolt and Nut, but this is very difficult (especially Quantity).:Pair (for Left and Right) (MF10 is a large strange thing, like if you do this, you can't put that, or if you put that, you can't put this afterwards. 。
I think it looks nice, so it's good for someone who can afford almost 30,000 without worrying about the details.
View detail
That's DAYTONA!
I guess it means that DAYTONA is the distributor of MAGGI, but the same size on Amazon is DAYTONA and Webike is MAGGI, then I should buy from Webike. So, I'll buy it from Webike.
I thought it was DAYTONA. Absolutely not." I was not saying that I wanted to buy DAYTONA products, but I wanted to avoid them because I have been making a lot of mistakes buying DAYTONA products recently, emotionally.
View detail
Processing required
The guide on the body side of the mounting bracket was not attached as it was because the body attachment part of the mounting bracket and the guide on the body side were in contact with each other. The screw fastener of the mounting bracket also interfered with the box part of the air filter when the length of the wrench was too long, so I wondered whether I should cut the wrench or not, but I loosened the box side and shifted it to close. View detail