Reviews
Just the Right Quantity for Tire Replacement:Set
[How is it used?
I purchased this product to replace a SUZUKI/CHOINORI Tire.
This is the first time for me to exchange Tire by myself.:Set.
Was the one you received as per Image?
It was just as Image.
This Quantity:In addition to the Set, Air Valve Puller and Tire wax were additionally purchased.
How was your experience with it?
It was my first time to replace the tires.:Thanks to Set, we were able to successfully replace the Tire.
Lever was also Simple and easy to use, but Quantity:2 pcs is a little short, so I wanted to get another Lever with an irregular shape.
[Points to note]
I was careful not to damage the rim with the lever when replacing the tire.
How did it compare to other products?
There was also a Tire Lever from another manufacturer, but I thought this product would be sufficient since the frequency of tire replacement is not that frequent.
View detail
Thin Socket required
Used on Ninja ZX-25R.
In addition to replacing the Tire by hand, we replaced the Valve with an L-shaped Valve.
It may be just Kawasaki, but the installation is tough.
The hole diameter for the Valve of OEMWheel is too narrow to use the Socket of normal Tool.
I tighten a 14mm nut, but the wheel hole diameter is probably less than 19mm and the socket will not fit.
I measured the outer diameter of the Socket and it is about 20mm.
It is impossible to tighten without using a thin 14mm Socket with an outside diameter of 19mm or less.
I had no choice but to lightly fix the Nut with Spanner without turning the Nut and turn the L-shaped ValveBody to tighten it.
When tightening, a thin layer of silicon grease must be applied to the rubber portion of the valve, otherwise the rubber will be twisted and deformed.
Note that if the Rubber is twisted and deformed, it can cause air leaks.
I was forced to prepare a small socket with an outer diameter for the next work, so I looked around on the Net for a lot of things.
I had no choice but to purchase a 14mm plug socket with an outer diameter of 18mm because there are no normal thin sockets available.
View detail
Thin and easy to use.
I used to use Home center, but this KTC is thin and easy to use. View detail
Easy to use and safe
I have used various Tire Lever and the handle and tip spatula are just right in bend and thickness.
Surprisingly, some large handles can cause palm pain, but this is a safe and easy-to-use product.
View detail
Easy to use
[How is it used?
I bought this because I use it on MotorcycleMain. The angle is easy to use.I use it on Motorcycle, car and bicycle.Mothers' bicycle is no good.
Was the one you received as per Image?
Street Image
How was your experience with it?
Easy to use.
[Points to note]
FLOVAL PROStyleTool Quick coupling One-touch type O-Screw Plug 20PMA Applicable O-Screw (R) 1/4
You have to buy these things separately to use them.
How did it compare to other products?
Memory is easy to read
Other items that would be helpful
Opinions and requests for Items/Manufacturer that should be purchased together
20PMA Applicable O-Screw (R) 1/Quantity:4 Why don't you put it on and sell it as a Set?
View detail
Keep one for now.
Easy to use, Basic and one of a kind Items to have.
It is as easy to use as DRC's heavy Tire Lever, KITACO's regular Tire Lever, and a domestic Tire Lever with a smooth tip whose name I forget.
View detail
Ease of use is good
Because I got Air compressor, first of all, I bought this product which can do Check and Inflator of air pressure together with Air gun of standard. When I start to be particular, there is a thing of about 20,000 yen only in the air gauge, but because it is no use to arrange everything with such a first-class product suddenly.
The long neck and easy to read air gauge are great for motorcycle use. The long neck construction is convenient for motorcycle use and the easy to read air gauge is a plus.
To the Impreza. "The Hose was bent at an impossible angle. I was curious about this, but I have the impression that it won't happen unless you're very unlucky. I didn't have any problems with it.
What I was more interested in was the Included Parts:. It's been mentioned in other people's impressions. "Quarter to 20 PM." The TAB coupler is not included. If you think about the popular compressor, you can just put this size coupler from the beginning, but why they sell it separately is a mystery. It costs about 250 yen per one, but I hope the manufacturer will install this size coupler from the beginning, because basically all aerodynamic tools for motorcycle maintenance use this size coupler.
View detail
The best Tire Lever I've ever had!
First of all, the ease of use is the best compared to the Tire Lever I've had
It was easy to get into the gap between the rims, and when I put the Tire in after it was replaced, it went in without difficulty
I only bought 1 pc as a trial, so next time I order, I'll be able to get more Quantity:I would like to have about 2pc
The one drawback is the high price I don't know if it's cheaper in terms of TotalCost without just canning the tube and making it puncture Okay?
View detail
One of the easiest levers to use
At first we used a cheap Tire Lever from Straight and Daytona etc I was there, but Race's seniors and friends at the supply store
I bought TSK and this KTC Lever after hearing about it from
It is true that the tip is thinner than that of the less expensive competitors, but the strength is also ensured, and this thinness, shape and Grip's Thanks to this, it became easy to work on the Large change
View detail
It is easy to use
I bought this forged Tire Lever because the tip of the Chinese Tire Lever purchased in the jungle broke The thickness and shape of the tip are exquisite and the feeling of use is also good View detail
Easy to use as it is for Motorcycle
Although other people are also written, it should be attached to the connection to Coupler
The trouble of going over to the home center is to make the convenience which can be ordered with Net unnecessary
View detail
It became easier to work
As others say differently, the tip of Lever is thinning. Therefore, it can be placed in a narrow gap, making the work very easy. The thickness of the tip is about 1 mm slightly. What I have from the past is 2 mm. It is nearly half the thinness. Quantity : I bought 2 pc, but I thought that I can buy another pc.
View detail
Lightweight, Compact, somewhat usable
Basically it is not a stationary tool but a carrying tool.
Light, short, flat shape so it's bulky.
The performance as a key Tire Lever is not compatible with a thin Spoon type.
Compared to that, it is still short, so I need power, somewhat thick dish surface is difficult to hook and hard to turn.
However, it can be used normally. Maintenance is easy as well as rugged because it has a simple shape without a grip portion etc..
It is a Material of smooth texture, but it does not slip even with oil, so that point is safe.
However, since there is not much smoothness, careful work will scratch the Rim and be afraid to attach the Wound so be careful.
It was not bone but quality was like good atmosphere that I wanted to touch without any meaning.
However, if you are using at home, if it's Main, we recommend a thin SpoonType with Grip with long handle, you can hold it firmly.
View detail
Since the Tire lever of a DAYTONA had dissatisfaction a little, it purchases as a Tire lever to three flat knots. The photographs are a DAYTONA Long tire lever from a top, a DAYTONA Tire lever, and KTC260. It is easy to put in the tip of KTC260
Since the Tire lever of a DAYTONA had dissatisfaction a little, it purchases as a Tire lever to three flat knots.
The
photographs are a DAYTONA Long tire lever from a top, a DAYTONA Tire lever, and KTC260.
It is easy to put in the tip of
KTC260 between a rim and a Tire most thinly.
Although individual user-friendliness tends to put in a DAYTONA Long tire lever and KTC260 equally, when using the Lever after it, a DAYTONA Long tire lever is easy-to-use.
It is although this is unavoidable since it is a problem of die length.
View detail
As what is called a Spoon Type of a Tire lever, it is a time-tested product.It is more convenient for there to be two in Tire clearing work.Although there is also a cheap imitation these days [ ], this product is clearly a little superior well [
As what is called a Spoon Type of a Tire lever, it is a time-tested product.It is more convenient for there to be two in Tire clearing work.Although there is also a cheap imitation these days [
], this product is clearly a little superior well [ of tip form (condition of thinness and an R), and Plating finishing ].Although it cannot say truly that he has no Rim protector, it is easy to insert and difficult to give a crack.The Rubber grip of a Lever end is also kind to a hand.Since
die length is 260 mm, it may not go to the reason for calling it omnipotent, but the turn of the 500 mm of last Class may surely come, but general work is managed satisfactorily.
View detail
Three kinds of tire levers were prepared by this tire change. One of them is this KTC tire lever 260. Friction with the wheel at the time of exchange did not peel off surface plating treatment, either. Moreover, since the surface is carrying o
Three kinds of tire levers were prepared by this tire change.
One of them is this KTC tire lever 260.
Friction with the wheel at the time of exchange did not peel off surface plating treatment, either.
Moreover, since the surface is carrying out the vine vine, there is an effect of beat wax, and it was easy to do work, and felt.
Although the tip is processed thinly, even the sign of bending is not felt in this work.
A good tool is user-friendly! He admired.
I think that it is a tool I want just the person unfamiliar to a tire change to use.
Although it is a little expensive, tool helps work. He has such a feeling.
View detail
Since it suffered troubles although the last tire change was working by the tire lever and slotted screwdriver of the daytona, it purchased this tire lever. Although the form of die length or the point is almost the same as the product made from a day
Since it suffered troubles although the last tire change was working by the tire lever and slotted screwdriver of the daytona, it purchased this tire lever.
Although the form of die length or the point is almost the same as the product made from a daytona, surface plating treatment has that smooth in the direction of this lever.
Since it does not feel rough, it seems to be gentle to a tire.
It will be easy to work if there are two.
View detail