Reviews
Fits: KAWASAKI Z1000 (air-cooled), KAWASAKI Z750 (air-cooled)
You can taste the effects, but …
You can taste the effect, but be careful because Tandem is deprecated!
I feel like I can tandem it, since it doesn't seem to lack strength from what I can see, but…
It would be nice to be able to taste the Lay-down effect without welding!
View detail
Fits: KAWASAKI Z1000, KAWASAKI Ninja 1000 (Z1000SX), KAWASAKI Z1000, KAWASAKI Ninja 1000 (Z1000SX)
The position attached simply is also OK!
The position attached simply is also OK! View detail
Fits: HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB110
You can choose the one you like and the way you want to ride.
After installation, I tried 6 levels of hardness for a total of 500km, and the hardest setting was the best for my preference (in terms of stability during acceleration and no fear during cornering). As a reference of hardness, I had been using Tokico's product with Benly 50-110 until last year, and in comparison between Tokico's factory setting and Tokyo-do's hardest setting, I have a strong impression that Tokico's factory setting is firmer. (*Note:At the hardest setting of Tokyo-Do, the handlebar shakes more strongly when it picks up bumps on the road surface in the high area of wide-opening driving. This problem was resolved by moving the hardness setting toward the soft setting. In the end, I am now using the second hardest setting from the softest. (I have the impression that the shock absorption of the NORMALCUB has only increased in terms of performance.) View detail
Fits: KAWASAKI ZRX400, KAWASAKI ZRX400II, KAWASAKI ZRX400, KAWASAKI ZRX400II
red-tapered ride
Installed on a zrx400? I haven't made any adjustments, but now I have the Habit to slow down before Curve and Gap!
It's good if you buy it second-hand and use it as a connection, because you have to send it in for repair!
View detail
The delivery date...
Anyway, the delivery time is slow. I had to be prepared to wait a long time, but it arrived on time. As for the installation, there is no explanation and the screws at the bottom are not long enough for the OEMBolt, so I used the thin nut that comes with the OEMBolt, but it is not a U-shaped lock nut. If you are worried about the strength, you can use HondaOEMBolt95701-120-7508 12X75 (Kawasaki discontinued). View detail
Replace with new one
I purchased this product to replace the front fork with a new one when I overhaul the front fork.
Material:Since it is a Rubber product, it has deteriorated over time and will be replaced with a new one.
It is sold as a Honda OEM Product, which is helpful because I can exchange it for a new one.
View detail
SE + 22nm
I installed it on a 19 MODEL H2SXSE+.
The actual measurement was 22mmDown.
Originally, SE+ seems to be about 10mm higher than SE, so it may not be the 30mm Down that Trickster says.
Even with approximately 20mm down, the effect was positive, and some of the footing anxiety was eliminated.
However, side stand parking is a little bit standing up, so care may be needed when parking on an incline.
View detail
For setting the vehicle posture!
[How is it used?
Used on XJR1300C with OEM suspension.
Was the one you received as per Image?
As per Image, it's Duralumin and super lightweight, but it's solidly built and seems to be very accurate.
I did not feel any concerns about the strength of the product.
Was the installation difficult?
If it is a regular XJR1300, it is very easy because it has a Center Stand.
In the case of XJR1300C, there is no Center Stand, so you need to use a Footpeg Stand or
It cannot be replaced unless the Motorcycle is suspended by the Frame around the Rear.
Even if you think you can just replace One Side at a time, it is absolutely impossible because the suspension length is in the direction of getting longer.
How was your experience with it?
To begin with, the XJR1300C has a slightly lowered body posture, which makes it easy to turn.
I need more Quickness! I thought it would be a good idea. First, we changed the Tire and chose Spur CORSA 180/60 flat.
The flatness was increased and the Rear ride height was slightly increased. Still, when we went to the mountain pass, the bank angle was not enough and there was no quick feeling.
By adding this product, it is possible to set up to the ideal vehicle height.
Another good point of this product is that the ride height adjustment function of the OHLINS can be utilized as it is.
[Included Parts:were they on?
A solid Instruction Manual is included. We recommend that you read it carefully before starting work.
[Was there anything that disappointed you?
I was a little concerned that there was some line Wound on the product, although it was not a Large thing.
I am sure that if you are a nervous person, this is the Level where you would return the product, so please keep quality control here.
View detail
Race ish casually
This ring measures the amount of stroke of the front fork.
So far I have been wrapping Tie Wrap around the Inner Tube.
Tie Wrap would have been perfectly fine, but we decided that a dedicated product would look better anyway.
The white ring has a cutout that opens into an inner tube.
A little hang is required to wrap the spring around the ring.
Be careful not to wrap the Spring too tightly or it will stretch.
It looks good and is kind of race ish, which is good.
This is also recommended for those who prefer these kinds of parts that give a casual race ish feeling.
View detail
something easy to do, e.g. to cover up a loose article
I purchased this to hide the deterioration of the Cap portion of the Top portion of the Fork.
Just Material:Since it is a RubberCap, it seems like it should be a little cheaper.
It does not seem to be loose enough to come off.
View detail
Replace with a soft one
I have been wanting to change the front and rear springs of my WR250R to softer ones for a long time, so I decided to purchase and replace them myself. if it is just the springs, I can easily replace the rear springs if I have an adjusting wrench, and I can replace the front springs by myself in a few hours. I was able to do it myself in a few hours. View detail
Fits: HONDA MONKEY125, HONDA DAX125, HONDA MONKEY125, HONDA MSX GROM, HONDA MSX125SF, HONDA GROM, HONDA MONKEY125
A little disappointing…
There was a slight error between the color in the picture and the actual color, and it didn't turn out the way I was expecting, so I took it off.
But the quality is not bad, and if you get into it, it's very good.
Installation is a bit of a hassle.
View detail
No problem with the product.
[How is it used?
I bought this to replace the Dust Seal on my TZr250R when I did the front fork overhaul.
It wasn't in the list of compatible models, but I thought I could use it because of the difference in the end of the part number, but no...
Was the one you received as per Image?
Quantity as shown in the picture:It arrived in 1 Set of 2pcs.
How was your experience with it?
In conclusion, TZr250R (STD) It was not available for
Part number for STD (3XV-23144-00) I thought they would be the same, but the inner and outer diameters were 1mm larger each.
I shaved off the outer circumference and tried to put it on once, but in the end I realized that the inner diameter was too large to hold the garbage! So I put it back. (Lol)
If the front fork of the RS or SP is of a different model, it should work fine.
The material and texture seemed to be the same as the OEM Product.
[Points to note]
If you are thinking of using it for the STD front fork, be careful.
【Review】
Compared to the OEM Product, the texture was fine, and the accuracy of the parts seemed to be fine, although the Size did not match.
It was my fault for not researching it completely and thoroughly, but I didn't get to actually use it, so I gave it 3 stars. (Sweat)
View detail
It might be good as a Dress-up.
I had ordered Red, but after a while I got a call that it was out of stock, so I changed to Gold.
Gold turned out pretty good too.
I think the delivery time was about a month or less.
View detail
Fits: Others For KYB36Z, その他 For KYB36Z, その他 For KYB36Z
Webike's response to returns and exchanges is still the worst.
I contacted them with photos and explanations as per Webike's return/exchange procedure, but they have yet to reply to any of my emails. But I still haven't received a single reply. I contacted PartsManufacturer directly because Webike is not reliable, and they sent me a replacement part free of charge the next day. View detail
Front For anti-rattling
You guys talk a lot about rear shocks.
The front of the Grom... Doesn't it have a really crunchy feel to it?
I bought it hoping it would help.
It's not like I'm an aggressive runner.
After you put it on... Well, it's a little better.
I suppose it depends on how you run.
I'd have to change the fork oil and the springs to get to the root of the problem. And the springs need to be changed.
Doesn't it feel right?
The product itself is well made, and the fork synthesis is a product that can be improved.
think
View detail
If you're looking for a lowdown, this is it.
If lowdown is your goal, the cheap Black painted Plate will do. The weight is almost the same as NORMAL.
The key Lowdown effect is Do you feel better now?" It was about the same change.
It's probably because lowering it further would affect Handling.
Replacing the Plate is a relatively simple part of the process, but it is recommended to have a Motorcycle shop do it as any mistake can lead to an accident.
View detail
![SPORTS LINE Rear Twin Shock [E Series] E302](https://img.webike-cdn.net/catalogue/images/50511/e302_01_TS.jpg)
Fits: YAMAHA XJR1300, YAMAHA XJR1200
semiOrderable and cosmetic Shock
[How is it used?
My friend bought a used XJR1300 with Chinese rear shock instead of OEMOHLINSShock, and it had terrible ride quality.
Was the one you received as per Image?
It was very well made and as per Image.
Was the installation difficult?
It is a special product for each model of car, so it is installed by Bolt On, but a friend of mine had it installed by a motorcycle shop.
I thought it would be easy to remove the rear shock nut and replace one side at a time if I just wanted to replace it.
How was your experience with it?
I borrowed it from a friend for two days and test rode it on the street and on a touring trip, and it works well as a Shock and rides very well for the price.
[Included Parts:were they on?
I gave it to a friend without opening the box, so I'm sorry, but I'm not sure about Included Parts:.
[Was there anything that disappointed you?
I don't have any complaints about the product, but if I had to say something, I'd say the outer box looks cheap, although I suppose that's because of CostCut.
View detail
Demerit not feel
I bought this when I was OHing my OEM suspension.
After the replacement, it became a little harder? I honestly don't know what the change is.
I don't feel like it's getting worse, so maybe I should try replacing it when I OH it.
View detail
Demerit not feel
I changed the Front Spring, so I changed the Rear as well.
Honestly, you might have to ride it to compare.
I don't think it's gotten any worse.
View detail