Reviews
Large things are not explained! It is much shorter than OEM!
Caution before performance crap! This suspension. It's short. (Angry)
It is listed as TW200/225 compatible, and since there is no explanation, I thought it would be the same size, but it is much shorter than the OEM suspension.
If it wasn't the same size, I would have hoped there would have been an explanation. If I had known it was short, I would never have purchased it!
Seeing things, Once I don't have a ShacoTan in my off car. I paid high gold to buy Garbage. I was disappointed.
I doubt the designer's Sense, even if it's the old fashioned Ska tune type Custom. no Sense!
However, I paid a good amount of gold for it, and since it has been sitting for about six months after purchase, I would not be able to return it......so I am in an atrocious mood,
Since it has a coilover function, I extended it to the limit and installed it. Still, it is a little shorter than OEM. Too bad.
Comparing the appearance before installation, the damper section looks thinner and poorer than the OEM.
Pre-road is installed as shipped. Attenuation is at its lowest.
The front side is equipped with a Cartridge emulator and pre-road is also applied.
When installed, the suspension itself is shorter, but the spring rate is higher from the beginning and the sag is reduced, so the Rear ride height is higher at 1G's ride. (The optical axis is lowered.)
This is not the kind of thing I wanted, but I feel ・・・・ indescribable・・・・
Normally I wouldn't want to give it even 1 star, but after riding it... not bad ・・・・
Things are not bad.
It's very well controlled and of high quality. It is clearly different.
Completely stiffer for on road use. The front end tends to cut into the road as the vehicle's ass rises higher than the OEM during cruising.
It picks up fine Gap and has a lumpy feel. However, when stepping on the Gap or swell while turning, it becomes a crisp and snappy leg without wobbling. It is honestly easy to ride.
I think this will increase the risk of cocking up when going off-road, and I don't think it will be a comfortable ride...
It is intended for long-distance travel with luggage, so maybe a harder taste that is not as heavy is not a bad thing...
Supple in the beginning, stiff in the back. Stroke is up if you want....
I didn't get what I wanted due to the lack of explanation, but things are good from a different perspective and well, this is what I got.... It was the Rear Suspension that made me feel indescribable.
I don't like even 1 star if it's just for the emotion. But considering the performance of the product, it's not bad at all, in fact, it's rather admirable. I rated it as 3 Stars because of this.
It is very good for on road driving....
Whatever the case may be, I would have liked to have seen a better description of the product.
This would be good for those who are customizing for on road or want to lower the ride height.
The stiffer design may be suitable for heavier people or those who carry a lot of luggage.
Sorry for the poem.
View detail
For use with the 3RW1 that is not the appropriate model year (but requires modification).
Compared to NORMAL, the large size of the footrest surface is obvious.
It is stable, but its thorns are sharp and long, so please use it with hardy boots that can shave off the Sole.
When used in 3RW, the Right Side must be considerably reduced to be able to be overthrown.
And even if it is installed after much effort, the rattling is so great and the return in collapsible mode is so weak that further modification is required.
If you are concerned about the details or if the modification is troublesome, you can install the expensive Bolt On. "ARE" is probably a good idea
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RSCAFE, KAWASAKI Z900RS, KAWASAKI Z900RSCAFE
I don't feel much.
I don't feel it much. I don't feel a huge change in the gear shift. I feel like the gear stops significantly when I go up from 1st to 2nd. View detail
Fits: HONDA Today, HONDA Today, HONDA DIO(4Cycle), HONDA DIO(4Cycle)
Repair is completed at a low cost!
Installed on ThirdMotorcycle's Today that goes to the nearby Convenience, replacing an OEM OEMRear Suspension that had been scuffed up and deteriorated. The price is very low, but I have had no problems with it! I am Large satisfied with the low price and the refresh! View detail
incomprehensible
Instruction Manual is too complicated and difficult for beginners. I think some knowledge is necessary. View detail
Those with big feet need to get used to a lot of things.
The work itself is BoltQuantity:It takes only 10 minutes because it only touches 2pc.
After installation, we went out for a test run.
At first I was not sure how hard to step on the pedal, and sometimes I wanted to go from first to second gear, but I soon got used to it.
All you have to do is step in with a firm clank!
What I was more interested in was the foot placement.
My foot is 28.5cm and the Outsole of the shoe is over 31cm.
As you can see from the picture, if you set the angle where the Down side Pedal does not hit the sole, the height of the Up side Pedal will be raised, or if you install the Up side down, the Down side will always hit the sole….
Anyway, it is quite tight for people with big feet.
There are various inconveniences, but I don't want to damage my leather shoes! I highly recommend it to those who don't want to damage their leather shoes!
Because that's what I bought it for, too.
It is not the Parts for which we are looking for a sense of operation!
View detail
Fits: HONDA monkey, HONDA Benly CD90, HONDA Super Cub 90, HONDA Super Cub 50, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA Benly CD90, HONDA Super Cub 90, HONDA Super Cub 50, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
I bought it just for the color.
I won't know for sure until I ride it for a while, but I bought it just for the color, so I am not particular about its performance. View detail
It looks good!
NC42Rear suspension was leaking Oil and I couldn't afford OEM because it was too expensive.
The item received is clean with some SmallWound! 。
Installation was not possible because the Bolt under the Right Side interfered with the Exhaust System to remove the OEM! Others were completed Smoothly. The upper part of the Shock was not easy to install, so I applied a little Chain oil as a reference to others and it went in. Also, one of the lower side had to be tapped a little to fit the holes in the mounting position. Also, it was impossible to mount the pon, so I had to extend the overall length by about 8mm to complete the installation.
The ride is not bad, but it feels soft, so I will adjust it. I don't know about durability, but there seems to be no oil leakage and no initial defects.
View detail
Easy to install
I had an Indicator, but I replaced it with this one. It's not very noticeable, but the price is low, so I guess it's okay! View detail
Getting the Center out is the hard part.
I was prepared for BALI and Small scratches, but I can't get the Center without modifying the Brake Panel side.
I also bought a 4mm Sprocket spacer but I think it will be useless.
Also, there is some distortion, so if you want to assemble it tightly, we recommend a reasonable price.
View detail
It cannot be pontooned. But Rim width is Quantity:Pair (for Left and Right) I like the fact that it's all even, etc.
I purchased Front 3.5J and Rear 4J. Please be careful. Personally, I think that the depth of the rim is more than enough.:Pair (for Left and Right) I bought it knowingly because I didn't want it to be a "one-size-fits-all" type of arm. If you want to mount it on your car, you should use KITACO or GKURA's Quantity.:It is better to buy a Set product. View detail
It didn't work
I tried to install it, but I have it set to short suspension.
What a surprise, Chain didn't hit Roller ….
I will try to install it again when I change to Normal suspension.
It would have been nice if you could have written something about not being able to use it if it's Lowdown.
A little disappointing.
So we do not know the effect of the installation.
View detail
Shift Pedal
GizaGiza synthesis on the part where the clutch is attached looks like a bad lick! View detail
Very good looking, but...
Pulling on the brake wire is important, but securing the rotating bracket is impossible with a screw lock, and the bracket inevitably moves. However, I think that a more ingenious bracket is needed instead of just using the OEM bracket. View detail
Fits: YAMAHA YZF-R1, SUZUKI GSX-R1000, KAWASAKI ZX-10R, HONDA CBR900RR, HONDA CBR1000RR
Four months for delivery.... The product is good!
Not conformity But I was able to use it for MVAGUSTAF3.
The front and rear suspension on the MVAGUSTAF3 is too hard. It is also played by the Gap in the city, and also gets pushed up on the highway.
I lowered the Initial and oil level on the Front, but it is still too hard to use the Stroke effectively.
I looked for a soft spring, but could not find one for F3, so I looked on the web and purchased this YSS with a similar spring diameter from Webike. However, the delivery time was long - it took 4 months from order to arrival.
YSSFront fork spring
[Outer Diameter ] 38.0mm
[Free Length 230mm
Spring rate 8.5N/mm
[Corresponding Model Type] CBR900RRFire blade、CBR1000RR、ZX-10R、GSX-R1000、YZF-R1
Compared to the OEM front spring, the free length is 10mm shorter, but the Initial Adjuster can be adjusted from 0 to 13mm to produce a proper 1G sag.
When I actually rode the car, it changed to a front suspension that normally works properly.
The Rear also can be changed to Spring by Hyper pro to create a standard Japanese suspension that can be enjoyed by Japanese people.
For F3, we recommend replacing the front and rear Springs.
View detail
Fits: SUZUKI ADDRESSV125S, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125
It looks very beautiful. But it bounces.
The rear shock of the ADDRESSV125S was damaged due to age-related deterioration, so we replaced it with a reliable KITACO shock.
The replacement itself is easy, just a 14mm Glasses Wrench, Phillips Screwdriver and a 10mm or 12mm Socket.
The overall length is the same as the OEM model (315mm), so it can be replaced without any change in ride height. The replacement was completed easily in about 30 minutes.
Pre-road is not touched and hung, and when I finally got on it, it bounced on bumps anyway. (Always one person on board)
I think the Spring rate is high due to the small number of Spring rolls, and I don't feel much improvement in traction, which I was hoping for the most.
I'm going to try to adjust it with pre-road adjustment etc., but I don't have high expectations for it. It is just too sticky and not at all flexible.
The effective Stroke seems to be short and I am wondering about the damping force against the Spring rate. I can't even feel the damping force.
It is too hard to shrink and too resilient. It is like the four wheels of ShacoTan.
The damaged OEM suspension was also Large approximate, but I didn't expect it to bounce more than that. Perhaps the OEM was more supple with the way the Spring was wrapped.
I thought it was a shame because it looks beautiful and the details look well made.
View detail
Fits: YAMAHA XS250, YAMAHA XS400, YAMAHA XS250, YAMAHA XS400
Sturdy Fork Boots!
The rubber has a good texture, is durable and reasonably resilient, so it was easy to install! However, it would be nice if it were a little cheaper! LOL! View detail
Fits: YAMAHA SR400 19, YAMAHA SR400 19, KAWASAKI Z125 Pro, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR500, YAMAHA SR500, YAMAHA SR500
Self-satisfaction Level?
I bought this product because the OEM cap was plastic and the texture was not good (dirt and fogging). View detail
To balance with Rear...
When replacing the rear suspension, I used a RateUp spring to get the balance.
I used #15 Fork oil for the installation.
Spring with the same Variable rate as the OEM, but with a RateUp of about 10%.
I couldn't tell the difference myself. (^^;)
View detail
Fits: HONDA MONKEY, HONDA GORILLA
I am satisfied with the accuracy, but to be honest, I think it is expensive.
I was a little hesitant about the price difference between GCraft and Minimoto,
I bought GCraft anyway.
When I looked at what I received, there was no engraving on it, just plain processed aluminum.
I wonder if the Center diameter and Screw hole positions are as accurate as they should be.
Given the price difference, perhaps I should have tried Minimoto.
View detail