Reviews
Think in terms of replacement frequency, not Power
I don't think there is anyone who can perceive the increase in inhalation efficiency by 0.5ps at Peak with SEROW in the product description.
I'm more of a wash and reuse kind of guy, but it's a lot more work than I thought it would be.
According to the official procedure, wash with Cleaner→ wash with mild detergent→ dry for a day→ apply Oil→ wait 6 hours and when Oil settles, you can drive.
Almost two days if you follow it exactly? If I wash on Saturday morning, I won't make it in time for Touring on Sunday.
If you're the kind of person who changes filters once or twice a year, OEM replacement would be better.
I guess it's for people who want to go as fast as possible in an hour-long Race to change filters in a month, which is often run in Course.
View detail
Fits: HONDA CB1300SBSP, HONDA CB1300SB, HONDA CB1100RS, HONDA CB1100EX, HONDA CB1100, HONDA CB1300ST, HONDA CB1300 SFSP, HONDA CB1300 SF
After 20,000 km
Purchased due to idling failure after full power. I am looking forward to the next Touring, but have not driven it yet. View detail
I thought setting was necessary.
BITO's Settled fcr,
what kind of state (Exhaust System, ignition system, etc.) I don't know if you did the Setting in the
It is unknown, so if you are particular about it, you will need a Setting that matches your vehicle.
As for the delivery time, it was originally scheduled to take about 3 months, but it arrived in one month.
View detail
I used it with FCR Carburetor Body28.
It is for vm26, but I changed the Spigot and used it with FCR Carburetor Body28.
In the case of CHALY, you need to engage a 6mm Spacer made by GCraft or Minimoto under the Manifold or it will hit the Frame.
As a precaution, the inside of the Manifold should be cleaned well before use.
The Manifold I bought had visible Level chips on the inside.
View detail
DAXAir cleaner
Good cosmetics,
Mounting Bracket Location OEM and
Spacers are not required because of the difference.
View detail
Helmet In Box needed to be modified.
Product Description With this kit, you can replace the carburetor without the need to modify the Helmet In Box or Cowl." but when the PWKcarburetor was attached, it made contact with the Choke Knob faction.
When the rear suspension sinks, the carburetor almost comes off as it is.
Helmet inBOX processing and Choke Knob processing were used to overcome the problem.
I'm a little disappointed and will be replacing it with Wire-style Chalk.
I don't know if I installed it the wrong way or not... (It only sticks as it sticks!)
View detail
Necessary for FCR Carburetor Body
Essential items for FCR Carburetor Body, not very durable. View detail
I just want the Rubber alone.
Rubber deteriorated and was lost while driving.
It would be helpful if you could sell only in Rubber.
It will deteriorate within a year.
View detail
Fits: HARLEY-DAVIDSON Vehicles with OEM CVCarburetor
Minimum Quantity to Overhaul carburetor:Set
I used this for an under-seat engine hole on a 2000 XL883XL1200C SPORTSTER 1200. The vehicle had been immobile for a long time and the Carburetor rubber parts were hardened and leaking fuel. The beauty of this kit is that it omits the Float, DiaphragmRubber, and other parts, and only requires a minimum quantity of parts.:The Carburetor functions have been restored and I am generally satisfied, but the rubber packing of the Float chamber does not fit perfectly and I am not able to assemble it. View detail
Fits: SUZUKI address V125, SUZUKI address V125, SUZUKI address V125, SUZUKI address V125, SUZUKI address V125, SUZUKI address V125, SUZUKI Address V125G, SUZUKI Address V125G, SUZUKI Address V125G, SUZUKI Address V125G, SUZUKI Address V125G, SUZUKI Address V125G, SUZUKI Address V125 Limited, SUZUKI Address V125 Limited, SUZUKI Address V125 Limited, SUZUKI Address V125 Limited, SUZUKI Address V125S
Size is Exactly but
I ordered this to replace an Air cleanerFilter that was falling apart due to hydrolysis without my knowledge.
I wasn't sure how much filter oil (sold separately) to apply, so I applied the oil as I usually do on off-road motorcycles, but it seemed to be too much, and air cleaner oil spit out from the silencer for a while.
There is no way to go wrong with the installation.
View detail
Replaced together with intake manifold
The purchased Spigot ring and intake manifold will be used to replace the Carburetor.
Size is almost the same as OEM Product. (OEM Product is discontinued and no longer available)
I need to check with the actual Motorcycle to see if it fits my Motorcycle.
View detail
I have concerns about durability.
I purchased this to install a Chinese FCR Carburetor Body35 on my FTR. It required some modification, but I was able to install it. View detail
Fits: KAWASAKI ZX-25R, KAWASAKI ZX-25R SE, KAWASAKI NINJA400, KAWASAKI NINJA250, KAWASAKI ZX-4RR, KAWASAKI ZX-4R
It will be such a thing
Used on the 2022 MODEL ZX-25R SE.
For ZX-25R, there are almost two choices, MWR or DNA.
MWR seems to be efficient, but it seems that thin sponges are used and dust collection capacity is questionable.
Pass because the inside of the Engine is likely to be unusually dirty, though it will produce Power.
Then DNA is the only option, so I bought this one.
The installation was Large strange because the Cowl and Tank were removed.
The thing itself is only fixed with a single Screw.
After installation, I took a test drive and did not notice any change.
The ZX-25R itself has a thin and peaky Torque, so I don't think you will be able to feel the difference.
It will be OK if you get the satisfaction of having replaced the Parts.
View detail
Used for YZF-R1
I used to use a Racing spec of this and it led to a significant power up, so I have trusted it as RaceParts ever since. View detail
I'll write it down, how to detach it. The engraving is so thin I can't read it.
I heard that it is a Setting option when adjustments with Jet needle don't work.
In my case, I replaced it with the lowest one as the last inspection point for the TMR, which was inevitably malfunctioning and could not be cured.
Although these parts are normally sold, some people may not be familiar with how to remove and install them, so we have written them down here.
Remove the throttle valve and jet holder (the tube with the main jet attached).
Thread the disposable chopsticks from the top side of the carburetor through the middle of the core, being careful not to touch the Hyper nozzle.
Using disposable chopsticks with a small Hammer, tap the press-fit Needle Jet into the Float side (no need to be stupid).
When installing the Needle Jet, the Needle Jet dropped from the Float side is tapped with a disposable chopstick from the Float side in the opposite manner to press-fit the Needle Jet.
If the Jet Holder had been Overtorque-tightened in the past, the Needle Jet would be deformed at the body press-fit area, resulting in a misaligned roundness and fuel leakage. The level of the removed Needle Jet was such that it was visually apparent that it was distorted.
I press-fitted a new one, one notch lower, and it completely eliminated the previous malfunction, so I was able to confirm that the deformation of the Needle Jet associated with Overtorque was the cause of the malfunction.Refreshing.
Since then, I have been using the TMR36 with only the Needle Jet being the first thinner from the factory pre-set, and it is working very well. I could buy a new Needle Jet again to completely restore it to the factory condition, but it is in good shape and I don't want to replace it again and again because it is a press-fit part.
I also have no problems with VSeal or O-ring under the cores, and I think this will allow me to enjoy TMR for a few years.
View detail
Fits: HONDA Super Cub 50 AA09, HONDA Super Cub 50 AA07, HONDA Super Cub 110 Pro JA44, HONDA Super Cub 110 Pro JA42, HONDA Super Cub 110 JA44, HONDA Super Cub 110 JA42, HONDA Cross Cub 50 AA06, HONDA Cross Cub 110 JA45, HONDA Super Cub 50 Pro AA09 All models, HONDA Super Cub 50 Pro AA07 All models, HONDA Super Cub 50 Pro AA09 All models, HONDA Super Cub 50 Pro AA07 All models
Cospa is nice.
CROSS CUB (JA45) ORing of oil drain bolt section.
Replace every Oil replacement, cheap and cosmetic.
View detail
All I wanted was Pilot Jet.
It was good until I installed the carburetor of AF34LIVE DIO on AF24TACT, but I could not decide the setting at all, and I wanted to squeeze fuel by Pilot Jet, but there was only Oversize, and I was using the common Pilot Jet with this car model. I looked up DREAM50 and found this product. I wanted to use only Pilot Jet, but I was so desperate that I bought this kit because Rose sales were not available. I think it's not profitable to sell Rose, so I don't think it can be helped. As for the setting, the Pilot area seems to be OK, but the Others area seems to be OK. (Main?) The company is struggling at the View detail
Fits: その他 FCR Single Carburetor Horizontal (H/Z) Large, その他 FCR Multi-Carburetor Horizontal (H/Z) Large, その他 CR-SPECIAL Carburetor, その他 FCR Multi-Carburetor Horizontal (H/Z) Small, Others FCR Carburetor Body Single carburetor Horizontal(H/Z) Large type, Others FCR Carburetor Body Multi-carburetor Horizontal(H/Z) Large type, Others CR-SPECIAL Carburetor, Others FCR Carburetor Body Multi-carburetor Horizontal(H/Z) Small Type
Setting is affected except for Keihin OEM
The other brand products and home center products have a lot of rattles and the needles are not only affected by the setting but also affect the life of the needles because they are violent. The cost performance is bad and considerably expensive, but I will buy Keihin OEM in the future because I had a considerably bad experience with cheap products. View detail
Fits: その他 FCR Multi-Carburetor Horizontal (H/Z) Small, その他 FCR Multi-Carburetor Horizontal (H/Z) Large, Others FCR Carburetor Body Multi-carburetor Horizontal(H/Z) Small Type, Others FCR Carburetor Body Multi-carburetor Horizontal(H/Z) Large type
Used for 4-cylinder 37
FCR Carburetor Body37 replaced when newly assembled, a little easier
Neck you can't change it unless you make it RoseRose.
View detail
Fits: HONDA DJ-1, HONDA DJ-1, HONDA Lead 90, HONDA LEAD 50, HONDA LIVE DIOZX, HONDA LIVE DIOSR, HONDA PAX CLUB, HONDA DIO XR BAJA, HONDA TACT, HONDA TACT, HONDA TACT, HONDA TACT, HONDA TACT, HONDA SUPER DIO, HONDA SUPER DIO, HONDA SUPER DIO, HONDA G DASH, HONDA Giorno, HONDA JULIO, HONDA DIO
I didn't feel the effect ….
Old Motorcycle about 30 years ago (about 5,000 km on the road) So, I replaced it with a new one for the purpose of refreshment, but as I am insensitive, I did not feel the replacement. The installation is easy because it is screwed on, but it is not difficult to access the Lead Valve because it is necessary to remove various parts, but it is large. View detail