Reviews
No other Size
Used for Horizontal TypeEngine HeadBreather Hose 650mm 6mm Diameter.
After searching for a compact product that could be directly connected to a 6mm inner diameter Hose, we found this product, which fits easily into tight spaces and meets our objectives.
Just look at the picture and Quantity:I bought it thinking it was 1 Set of 2pcs. but in fact it is Quantity:It was 1 pc. so it was disappointing in terms of cosmetics.
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA CHALY 50, HONDA CD50, HONDA BENLY50S, HONDA CL50, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA CUB press 50, HONDA CUB press 50, HONDA CUB press 50, HONDA CUB press 50, HONDA LITTLE CUB, HONDA LITTLE CUB, HONDA MONKEY BAJA
Required if Bore up.
When the engine displacement volume is increased by bore-up, the scale of explosion becomes larger than that of the OEM, and the oil pump designed for 50cc of the OEM cannot keep up with the oil circulation. Therefore, we introduced the Reinforced Oil Pump.
[Oil pump's role].
The oil pump pressurizes and pumps the engine oil to circulate it to the various parts of the engine. 。 This enhances lubrication, cooling and cleaning effects.
[What happens due to lack of Oil circulation.
→ oil film breakdown and increased oil temperature.
The oil pump sucks up engine oil that has accumulated below the waist and circulates it above the waist. (The oil then flows back into the lower back to continue circulation.) Cylinder Cylinder head Camshaft Piston Therefore, if the oil cannot circulate properly, there is a possibility that these parts will break. To explain this in a simple way, if the oil film on the parts runs out, the parts will be damaged and the oil will be lost. [Burns in] it appears as if ... 。 Naturally, parts that are seized are unusable and must be reassembled.
Effects of Reinforced Oil Pumps
Circulation of the proper amount of oil reduces the burden on the parts of the drive unit. 。 Also, by increasing the Engine Displacement Volume, a larger volume of oil can be circulated to the engine, which generates more heat and thus cools the engine even more.
*OEM oil pumps are designed for OEM for 50cc, so if you bore up, you will have to reconfigure the oil pump with an enhanced (higher discharge) oil pump to match, or the oil will not be circulated in time.
This Oil pump has a capacity = amount of Oil to send 。 If OEM Product is diverted, the capacity will be as follows ： Assuming that 50cc is 1.0, it is about 1.8 to 2 times larger.
good point
Heat generation from the Engine after driving has subsided.
Even if you go for a long ride and turn it around a bit, there is no longer any heat drop.
Idling is stable.
A bad point
I also removed the oil, removed the →clutch cover, and replaced the →gasket.
It's worth changing, though (laughs).
When you bore up the engine, it is strongly recommended to install a Reinforced Oil Pump. If you are looking for a domestic manufacturer, SHIFT UP is the cheapest.
If the Bore Up Kit you purchased becomes useless because you were too stingy with the Gold amount, the cost will be large…. 。 Some of you may have assembled the Bore Up Kit with the NORMAL oil pump, but it is not a stingy PARTS, so I recommend not to drink that opinion too much.
If there is room, it would be even more effective if the orifice of the oil coming out of the oil pump is enlarged.
View detail
Almost the only external Stud bolt
Since DAYTONA's reinforced Stud was discontinued, there was no other choice but to purchase an external Stud.
However, I have heard that it is stronger than OEM, so I am hopeful about the performance of the one I chose by process of elimination.
View detail
CUB to Blowby hose in!
CUB I put it on first, of the Blowby hose. The price was good and inexpensive. View detail
SHIFT UP
I like the products of this brand. I'm looking for parts to create a custom look for my Monkey. This product not only has a beautiful appearance, which is combined with other installed elements, but also has functional properties (engine cooling). I had great pleasure working with this part. View detail
Fits: HONDA Super Cub 90, HONDA Benly CD90, HONDA monkey, HONDA Super Cub 90, HONDA Benly CD90, HONDA monkey
Exhaust Studs
These feel great but were missing the nuts to hold the exhaust on. not a problem but would be nice if they were provided as showen in the pictures View detail
Fits: HONDA XR100 Motard, HONDA Ape 100, HONDA XR100 Motard, HONDA Ape 100
ape100 engine Knock Pin Set
There is no difference from the About quality and textured product It's not used yet. It's going to be used for engine overhauls Recommended if installation difficulty engine disassembly is possible Cost performance and comparison with other products It is easier to buy and use compared to std products WeBike packaging is always great, arriving in a week for delivery and packaging Concerns, precautions, or advice when purchasing Since it is an aluminum product, it must be stored clearly I recommend this product if you do engine overhaul View detail
Recommended
Replace while engine overhaul
I don't know about performance w
View detail
Product # 205003-11
Due to the existing need for engine cooling on my HONDA MONKEY after installing a larger cylinder, I was looking for solutions to this problem. One of the options was the use of a lid with cooling fins. A pleasant addition was the presence of a more technological appearance instead of the old, lost-looking lid. The quality is without complaints. View detail
It was replaced at the same time when 88Bore up, but it cannot be tightened subtlyQuantity:Set item
Used when assembling DAYTONA's 88Kit on SUPER CUB.
Since the cylinder stud bolt tends to loosen easily, I have been using a reinforced stud that can be used with a long nut for a long time. However, since the DAYTONA reinforced stud that I love is no longer available, I chose this one.
After assembly and test run, oil leaked from the head and base gasket. After re-checking, there was no problem, and retightening was done again and again, but to no avail.
I looked at the amount of screw threads coming out of the head cover and the long nut that came with it and noticed that there was not much difference in length. I found a used reinforced with stud nut that was slightly longer than the cap nut, and tightened it at the specified torque!
I don't know if it is an individual difference or a difference in the manufacturer, but the Quantity:The set product Nut could not be tightened sufficiently.
By the way, Stud itself has no problems.
View detail
For Oil cooler installation
I purchased this product to install Oil cooler.
Maybe the color is only Black since it is used for Grom?
Black is probably better for the custom feel, but I was hoping there would be a Silver version as well.
The oil cooler is the same SHIFT UP Original 12-stages Oil Cooler Kit.
It also has a cooling effect, so the objective is achieved.
It is tempting to make it a CartridgeOil Filter, though,
It is hard to replace the clutch cover for the oil cooler for less than 3,000 yen.
View detail
Beautifull finish.
Breather Hose 650mm 6mm Diameter attached at the outlet.
The hose used has an inner diameter of less than 10mm and an outer diameter of a little over 15mm.
It didn't match the Size on the Tag.
I was able to install it properly.
However, it was a little tight when fitting the outer end to the Hose.
After spraying CleanerSpray and pushing hard, I was able to insert it deeper.
It is secured with Hex screws, so there seems to be no worry about it coming off.
View detail
Fits: HONDA Super Cub 90, HONDA Benly CD90, HONDA monkey, HONDA Super Cub 90, HONDA Benly CD90, HONDA monkey
When replacing an external exhaust system
I purchased this bolt because the OEM stud bolt was not long enough when replacing an external exhaust system.
I have driven about 20,000 km since I replaced it and have had no problems.
View detail
Fits: KAWASAKI 500SS Mach III (H1), KAWASAKI 500SS Mach III (H1), KAWASAKI 500SS Mach III (H1), KAWASAKI 750SS MACH III (H2-A), KAWASAKI 750SS MACH III (H2-B), KAWASAKI 750SS MACH III (H2-C), KAWASAKI KH250, KAWASAKI KH400, KAWASAKI KH500, KAWASAKI Z1, KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI 750SS MACH III (H2-A), KAWASAKI 750SS MACH III (H2-B), KAWASAKI 750SS MACH III (H2-C), KAWASAKI KH250, KAWASAKI KH400, KAWASAKI KH500, KAWASAKI Z1, KAWASAKI Z2 (750RS/Z750FOUR)
SHIFT UP Oil Tank Filter Adapter
Reproduct sales will be Large change helpful since OEM Parts are no longer available.
Material of the product is also Material:It is a good product with solid construction of Aluminum with Black Anodized treatment.
View detail
Refreshing、Polished
I like the way the OEMs bend first, but this one has a root bend, so it's easy to kick when you KICK, and then recoil from the KICK to get back to where you started. View detail
Breather
About quality and texture a pretty good quality finish About the feeling of use There is no difference from SHIFT UP BREATHER HOSE END PRODUCT #950021-02 Products to buy together Carbon Oil Catch Tank [616-1432200] - KITACO Internal diameter 8 mm hose Difficulty of installation EASY Cost performance and comparison with other products I installed SHIFT UP BREATHER HOSE END PRODUCT # 950021-02, but I didn't like the hose fixing, so I chose this product and I was able to finish it neatly About shipping and packaging It took a week and the packaging is great Any concerns, cautions, or advice when purchasing It was nice to have a clean finish, and it feels a little special. Kitaco oil catch and internal diameter fit well, so there was no problem installing it View detail
Fits: HONDA XR50, HONDA XR100, HONDA NSF100, HONDA APE100 TypeD, HONDA XR50, HONDA XR100, HONDA NSF100, HONDA APE100 TypeD
Recommended
Purchased this product because the OEM was hitting my APE when I installed Over Rear Sets.
Good looking and practical!
View detail
This is the wrong car model.
I bought it for CUB90. But when I received it, I found it was for Monkey gorilla.
After closer inspection, it seems that the correct SHIFT UP part number for the CUB90 /cd90 is 920616.
View detail
This is for 50cc's!
I thought I bought a Stud bolt for the CUB90, but it was for the 50.
I bought it without thinking because it was compatible with CUB90 and cd90, but it was a mistake.
The product is listed as for Monkey gorilla in both the Package and conformity of the product. Oh come on, give me a break.
By the way, the correct Parts number for SHIFT UP's CUB90 is 920506-16.
View detail
Oil Catch Tank
About quality and texture The product is well organized About the feeling of use If the weather is hot or the rubber is worn out, I think the product will disappear without realizing it Products to buy together oil catch Difficulty of installation easy, simple Cost performance and comparison with other products It was nice to finish it neatly And the product composition is good. It also provides hexagon wrench About shipping and packaging It took a week and the packaging is great Any concerns, cautions, or advice when purchasing I chose this product as an option that I can choose, and I bought it because many people seem to choose this product, but I'm a little nervous because I press the hose to fix it. View detail