Reviews
I'm good.
Replacing the CDI on a '92 SR500 that had failed.
Thank goodness OEM Product was already discontinued!
Installation is done by connecting the Connector to the Quantity:It was easy to install the 2pcs. CDIBody is attached to the Frame with Tie Wrap.
It is equipped with an advance angle adjustment function, but I have set it to the NORMAL position for now and will experiment with other positions in the future.
I'm not sure how durable it is, but I'd appreciate it if it lasts longer.
View detail
Improved rev characteristics at high RPM
This is an imprementation used for KSR2 (B6).
The OEMCDI for KSR2 is built into the Ignition coil, so if you want to replace it, bothQuantity:The set is recommended. I had previously obtained a kit that came with this KSR1 Ignition coil, and I incorporated it at the same time as the SUS441 Reinforced Ignition Coil.
I fixed it to the space under the tank with the Tie Band along with the included Sponge, but I am a little concerned about whether or not it will have a vibration-induced trouble.
When actually driving the car, the Torque at low RPM is clearly lower, but the power output characteristics are more extended, making the driver want to use the higher RPM range more. It is like when I installed the HRCKit on my 4-stroke Racer replica in the 90's. It is not a drastic change, but it is a more aggressive and aggressive response. It is not a drastic change, but it is a more 2-stroke-like characteristic that can be enjoyed by the driver as it is more focused on the high rpm range.
View detail
It was an instant scare.
Purchased on 1/24/2024 3/1/2024 only a little over a month later the fire stopped flying… It's the worst. View detail
3KJJOG POCHE (Bore up, Big carburetor etc.) I installed it in
3KJJOG POCHE (Bore up, Big carburetor etc.) I installed it in
I purchased a Chinese CDI and installed it, but the Engine would not start ….
I gave up and looked for FOR JAPAN MODEL items, but the wiring did not match ….
I bought an Axis model with matching wiring and installed it, and it started the engine!
I haven't done any actual driving, but I think it is probably Large sturdy.
View detail
Fits: HONDA NSR50, HONDA NSR80, HONDA NS-1, HONDA NSR50, HONDA NSR80, HONDA NS-1
Made by POSH for peace of mind
Seals have been replaced due to engine overhaul. We will be assembling it from now on. View detail
Recommended for those who enjoy Setting.
In case of analog type such as SR400, the effect of CDI replacement is (゜゜) I think.
Roughly CDI replacement.
The following effects.
1. Limiter can be disengaged. Electrical Limiter can be disengaged by installing an external CDI 。 The →SR has no limiter, so that's not the point.
2. Power, acceleration characteristics, response, etc. are improved over those with NORMALCDI. →Coil or Plug and Quantity:You can feel the effect when you use Set.
3. It maintains strong ignition power even at high rpm. It is beneficial to add →external carburetor, etc., as it will be closer to high rpm.
4. Remove Rotation Limiter. → I don't think this is relevant.
And this POSH has 4 types of ignition timings to choose from.
Map1 Angle of advance from NORMAL
Same as Map2 NORMAL
Map3 Delayed angle from NORMAL
Map4 LAGGER ANGLE THAN NORMAL
Says Rucksack Li simply 。 Power increases as the angle of advance increases.
Why is an advanced angle better? (Sometimes a slow angle is better)
When the engine speed is high, the crank rotation angle is too fast for the gasoline to ignite and spread, and the engine rotation angle and the gasoline spread will not match. 。 Therefore, at high RPM, it is necessary to ignite the ignition at a slightly faster timing than the angle of the crank (called "advance angle"), so it is necessary to control the ignition timing according to the engine RPM.
CDI in a nutshell, Parts to determine proper ignition Timing by Spark plug. The external CDI is designed to fully exploit the Potential of the target engine. The CDI is designed to optimize the ignition timing according to the engine displacement volume and tuning degree.
Currently I use Map1 or Map2.
Map1→When you want to turn GunGun.
Map2→Touring, etc.
good point
Installation is also easy with OEM and conversion.
○Idling is higher, so it is easy to be half-crazy.
The last seasoning, which is easy to feel the effect when changing the ○carburetor to an external one.
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA Ape 50, HONDA XR50 Motard, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA Ape 50, HONDA XR50 Motard
6VMONKEY Maintenance Shift Arm Part Oil Seal
6VMONKEY Oil leakage from the oil seal of the change shift pedal gradually became a concern, so we replaced it.
The procedure is
(1) Apply a slotted screwdriver to the outer circumference of the oil seal currently installed and tap it to the center. (This work is important in case of sticking)
Screw the screw into the oil seal installed.
(3) Slowly pull out the Screw with pliers.
The oil seal of ShiftChange Pedal is thicker than other oil seals, so if the above method is also difficult, tear off the rubber around the shaft and pull out the gold part of the oil seal with radio pliers!
insertion
I used PVC pipe over a moderate flat washer.
View detail
Used as a grapple when making your own Torque rod
Not high intensity or anything, just Material.:Stainless SteelM8Stud bolt.
Originally Stud bolt for SR400/500 Exhaust System, these parts are designed to replace the Rust-friendly OEM Stud.
I used it as a joint for making my own Torque rod for Brake, not for its original purpose, so I don't have an impression of it as an Exhaust SystemStud.
Since it will be used on a part that is exposed to high temperatures from the exhaust (which is why the OEM steel stud bolt will rust quickly and violently), I feel that stainless steel will seize and be difficult to remove next time.
After aligning the screw threads by putting a tap through the screw hole on the cylinder side, apply heat-resistant grease (thread compound) or the like before assembly, or you will likely face hell later on.
Even with a normal exhaust system replacement, the nut that holds the exhaust pipe flange is likely to burn out easily, so the use of a thread compound is probably a must.
What makes this Stud bolt different from other very inexpensive UniversalStuds is that the end of the Screw can be hung with a hexagonal wrench!
Stud bolts are usually attached and removed with a double nut that requires a bit of hang, or with a StudWrench, a special tool.
Material:I'm not sure about using it as an Exhaust SystemStud when it is Stainless Steel, but it would be good for those who cannot tolerate Rust.
View detail
Fits: HONDA GORILLA, HONDA MONKEY
Pimp to Normal cab
It is used for the normal cab of LITTLE CUB. The air screw is hard to turn, but it is very helpful to adjust the idling easily when waiting for a traffic light, etc. View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
To MONKEY's Overhaul.
I bought this for overhaul of my MONKEY. I had a hard time deciding, but I decided to go with this one because of the price. View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
For Monkey engine maintenance
I used it for servicing my MONKEY and it is a must have for Engine Overhaul. View detail
YZF-R1 is M14
I bought a Washer for M14 for my YZF-R1 (2018). Some people use it 3 times, but I am afraid so I replace it every time.
It is not very profitable to pay shipping charges and hundreds of yen for one order, so it is more economical to buy these kinds of items in bulk, about 5-10 pieces at a time.
View detail
Fits: HONDA GROM125, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
I made a mistake.
It doesn't seem to fit jc92.
The diameter was totally different.
With 10,000 kilometers on it, it wasn't that worn.
View detail
It is hard to feel the change in physical sensation.
I recently tried it out before replacing the OEM CDI.
To be honest, I didn't feel the Merit of the exchange.
The ignition timing was gapped and there were many stalls.
According to the person in the know, it's a good idea to try it with different angles of acceleration... I've tried various things... It's true that high rpm is good... but low rpm is the specialty of motorcycles.
good point
XX You can buy it for almost half the price of OEM.
I feel like I'm getting faster.
A bad point
○ Not as durable as OEMCDI.
The engine stalls frequently when idling. I thought the ignition timing was not correct.
It is not compatible with normal cab bodies.
I think it would be a good fit for crunchy Tune vehicles, and I think you will find it cosmetically pleasing.
But I think it is not suitable for those who want to maintain the NORMAL characteristics and want to keep running.
I knew I had to settle for OEM.
View detail
Used for reproduction of old cars with direct cord
[How is it used?
old car (SportsCUB) Used in Restore of
Was the installation difficult?
Both cords are not too difficult to screw in.
Remember to put the Heat Shrink Tube through beforehand.
How was your experience with it?
Once again, I thought it might be a little dangerous since the insulation is taken only by Heat Shrink Tube.
If the Tube is Gapped or frayed and breaks, high voltage is exposed.
Installation location should be noted.
[Included Parts:were they on?
Instruction Manual is provided, so you will not get lost even if it is your first time.
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
Replace while opening Engine
Quantity like this:When it comes to Sets, there are some things that are not necessary, but this Quantity:Set is just what I need, so that helps. View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
Replace during overhaul of Monkey engine
I replaced it at the time of overhaul of the Monkey engine. Since it is a consumable part, I thought it would be safer to replace it at the engine opening timing, so I replaced it. View detail
Fits: Others NS1:NSR50:TZr50R:TZM50R:RZ50:MONKEY 12V:GORILLA:APE50:APE100:TW:SR400:SR500 etc
Colorful and Beauty.
[How is it used?
I purchased this product along with a plug replacement because the Engine was not working properly.
Was the one you received as per Image?
It was softer Material than Image.
Was the installation difficult?
Simply replace with OEM Plug cord & Cap.
How was your experience with it?
I am not sure about the functionality of the engine, the startability of the engine was not different and I could not feel any difference.
[Included Parts:were they on?
None in particular
[Was there anything that disappointed you?
The functionality did not change, but the appearance became Beauty.
▼I might be able to tell the difference if the body is an older year, but I couldn't really tell.
View detail
pochPlug cord
Used on a Uotani Coil. Perfectly sized and installed with no problems. View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
It can be used for CD90!
[How is it used?
The shape changed and hardened over time, leading to the purchase of a new one.
How was your experience with it?
Elasticity returns and Oil does not drip.
You can operate the system without worrying about leakage.
How did it compare to other products?
OEM Parts is slightly cheaper, but I was in a hurry.
That said, the price difference is within the margin of error, so you should purchase according to Timing such as Sale.
[Points to note]
Material when exposed outdoors for years.:Deterioration is inevitable because of Rubber products.
Recommendation for periodic replacement.
O-rings, which are not oil-resistant, are sold at home centers as water supply packing, but dedicated products are safer and more secure.
View detail