Reviews
Rust generation
Installation is left to you at your favorite store.
If it is not rust-proofed, it will rust in less than 6 months..............................
View detail
It looks nice.
It is a hassle to put the Wire Stopper in the Clutch holder. View detail
Replace to match Brake master
Clutch holder was also replaced along with the brake master.
Almost 90% for looks, not sure about functionality.
It comes with a RatioAdjuster, so you can change it to your liking.
Clutch is originally light, so use standard values
Maybe if NORMAL is 34mm and use 32mm adjuster.
Clutch is lighter, but the increased stroke = increased semi-clutch area = loss of sharpness.
I don't know how much 2mm would change things because I haven't done it.
I'd rather have Sharp controls than Dull controls.
I think the texture is okay, but the information on the Net is not.
I heard that individual Parts rust quickly.
Certainly the Holder in the Oaktion and other places is rusty and soggy.
I often see that it has become
The Instruction Manual that comes with it also says to spray rust inhibitor on the rusted areas.
I wanted the selection of Material to be reviewed when the price was raised from the old price of 30,000 yen to 40,000 yen.
or thereabouts GALE SPEED is where you can't become a first-class Brand.
View detail
Is the reduction effect small!
To replace the OEM Clutch Lever, it is necessary to remove the Bar End, Grip, and Switch Box, and it is necessary to be prepared to replace the Grip depending on the situation. We tried to install and adjust it in combination with Unicorn Japan's 2-way clutch release arm, which was introduced earlier, but we could not feel the effect as much as the combination of OEM clutch lever and 2-way clutch release arm. I did not notice much effect compared to the combination of OEM Clutch Lever and 2-way clutch release arm. I think it looks a little better, but I have to evaluate that the cost performance is low. View detail
It's lighter, but...
Clutch becomes lighter. It makes waiting in traffic easier. But it's expensive. 、、、、 View detail
25% lighter than before
I have pain on my left wrist because of squeezing clutch lever. After change, I felt 25% lighter to operate clutch lever. It wasn't dramatic change. But it's worth. View detail
The range of motion may be too wide.
It is good that the pull on the Clutch has become lighter, but the pull range has become wider (Large). (It is a matter of course) Therefore, it is possible to pull Lever farther to Quantity:Because it has to be set, and my hand is not so large, it becomes somehow difficult to handle. It is the main point of view.... View detail
Fits: Others
The width of Clutch meat widens → Long time to grab → Tired of hands → get used to → ask what you bought for yourself
L29 (Short lever) Although it is a feeling of use, it is honestly subtle. Besides the events of the general comment, the cause of exhaustion is Lever too thick, I think that it is also in the position to put your finger, but even though thoughtfully mistaken, I gave up because it is Wire drawing after all. I did not match Mini bike. Also there is hang in the installation of Lever side Wire Stopper (Although it is written in the Instruction Manual, it is insufficient, Pivot gets little by little as you make Lever outwardly and it can be laid out Line).
Self-assured world of parentheses only (I should have done to Berlin).
I got caught on the top of the Lever part with kohken, and wanted to make it the simple is best, unnecessary thing.
View detail
![Mechanical Clutch Holder L-29 [Holder Only]](https://global.webike-cdn.net/photo/article/86/1457188706586L.jpg)
Fits: Others
If looking and Custom focus, there are also purchases!
ACCOSSATORacing clutch,
GALE SPEEDWire Clutch Holder Kit,
I was worried but brembo's MechanicalClutch Leva
As it is currently installed, the price 32000 yen (tax-excluded) of
We selected only Holder L-29.
We only port the Lever division.
Holder comes with Clutch switch.
Clutch switch has 2 Patterns.
Wire play adjustment & Lever position adjustable.
The Clutch switch can be a Small Type,
I feel a little tired..
Three lines are connected, but when installing,
Treating it somewhat seems to break from the root Pin.
Especially finger Quantity : People who are 2 pc or 3 pcs,
Feeling the Wire to be drawn,
If you do not set Lever to a long distance
Clutch may not run out.
Making a little play makes it lighter,
No problem if you cut Clutch with 5 fingers.
Look, brembo's Brake MASTER and
It is GOOD because I feel unity.
However, the color was not better than I thought.
The price is also high (With Lever, tax included 40,000 yen over) ,
It was slightly lighter than NORMAL,
There is no need to forcibly change.
As stated above, if you are concerned about the appearance it is Recommendation.
Do not forget to buy Seal of ItalyMark on bespoke.
Depending on the model, Clutch
Because it seems there are times when it can not be cut,
Type of Holder is L-24 or L29 or L34
Let's choose firmly from Lineup.
View detail