Reviews
![[Repair Parts] Clutch Assembly](https://img.webike-cdn.net/catalogue/images/88698/03132252_5c890b0507d02_TS.jpg)
Fits: YAMAHA FORCE 155, YAMAHA SMAX, YAMAHA Majesty S
Don't buy it.
Bought this to replace a worn out clutch. 39mm nut can be replaced even if you can't loosen it with the integrated Driven! And it's cheap! It was a mistake to choose it with such an idea.
When I checked that it was assembled properly and turned the rear tire a little, I heard a strange noise like "PelePera". After turning it a little and reassembling, the noise did not occur, but it sounded depending on the phase of the driven.
And when I actually used it, I was impressed that the clutch connected at about 3000 rpm immediately after assembly and the sharpness of starting was restored, but after only 40 km of driving, an abnormality occurred. However, after only 40 km of driving, the start became sluggish to the same extent as the worn-out condition. (RPM at this time:6000 rpm)
I had no choice but to keep driving the car, and the connection got better again, which is not so clear, but when I drove the car more, I heard a strange noise like a skirring sound at the start. When this happens, no matter how carefully I try to connect the clutch, the clutch slips and the starting becomes incredibly slow. After riding for a while, the sound was gone, but the car started back to the same nippy start as before the replacement. I had not even driven 1000 km so far.
At the end of the day, the car hit the GuardRail foundation during a sudden stop while controlling a slow start and was almost scrapped. Although my driving was the main cause, I cannot deny that this Part was a remote cause.
It should be replaced with OEMClutch with the proper tools.
View detail
Clutch operation mitigation measures
It was not as effective as expected due to the inclusion of the Reinforced Clutch. View detail
OEMClutch Cable does not fit in DG32JXG250 TRICKER
[How is it used?
Planned to install it on Mrs.'s shopping MotorcycleDG32JXG250 TRICKER.
Was the one you received as per Image?
The accuracy itself seemed to be adequate. I was concerned when I saw an impression on another mail order siteReview that the cable guide of the car Both Sides was broken, but it is true that the parts in question are thin-walled and look fragile.
Was the installation difficult?
It was not possible to install the XG250 TRICKER because the Clutch Cable diameter of the XG250 TRICKER is almost the same as the Cable guide diameter. Photo Quantity:I was able to fit it into the groove as shown in the first pc. but the Cable could not be slid at all. We gave up on the installation.
In the above-mentioned other company's mail order site, there was a review that it was attached to Toracer (but the Clutch Cable became frayed and was removed soon after). (I don't think it's possible), or maybe the spec. of this product has been changed… (It's a mystery).
LargeCable guide diameter seems to be about 2.5mm, although this is a rough measurement.
I think it is not a crackpot, because I bought it from another company's mail order site (trustworthy) because it was out of stock for a long time at *WeBig. （I think it's not a crackpot.)
How was your experience with it?
Unavailable. It's a shame.
[Included Parts:were they on?
Two types of ShortCable (long and short) are included. You can choose according to the type of car.
[Was there anything that disappointed you?
As mentioned above, the Cable guide diameter seems to be too thin.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
At the very least, I would like to see descriptions such as Cable guide diameter xxmm, car Both SidesCable diameter up to Large xxmm, etc.
Photo Quantity:1 Set of 4pcs. As you can see, the accuracy is not so bad compared to MousseRACING's products, but if you can't use it, it's not worth it.:1 Set of 4pcs. I took this photo to show that even though the eye is so small, it's nice and light... I'm sorry that there is no comparison of Cable guide diameter. I would like to measure MousseRACING's one if I feel like it. I will measure MousseRACING's cable guide diameter when I get around to it, but it seems to be larger than ours, so it will probably work for the XG250 TRICKER.
*Photo Quantity:The 1pc. eye Washer is pictured with a different intention, please ignore it.
View detail
Fits: HONDA Lead 50 AF20, HONDA Livdio AF34, HONDA Broad Cabina AF35|AF42|AF52|HF02, HONDA TUDAY AF67, HONDA TUDAY AF61, HONDA Dio Cesta AF68, HONDA Dio Cesta AF62, HONDA Dio AF18, HONDA takt jorno af24, HONDA Tact AF31, HONDA Tact AF30, HONDA Superdio SR ZX AF28, HONDA Superdio AF27, HONDA Gyro-up TA01, HONDA Gyro X TD01-1400001-
This is a paperweight, Garbage.
For SUZUKIShoe is attached to Plate for Honda, a very inferior product.
When Washer and Spring are removed, Arm is wobbly, so discard it even if it is new.
View detail
Fits: HONDA APE 100, HONDA NSF100, HONDA XR100MOTARD
Lightweight Driven gearCOMP
I have been waiting for 6 months and when I inquired about the delivery time, they made excuses and said they were not sorry and that they would be fine with cancellation. I waited for two weeks, which turned into two months. I got mad and kept waiting and it took 9 months …. And not a single word of apology …. They are a joke of a Manufacturer. I will never buy from them again. View detail
Fits: HONDA Superdio, HONDA Superdio, HONDA Dio (2 Cycles), HONDA Dio (2 Cycles)
It sucks
How about aiming for the highest speed? So I bought it because it was.
But when I installed it, because the highest speed obviously fell, when I confirmed it in the homepage of KN Planning, it was said that it was possible to make more low GEAR.
What is the highest speed target? Bullshit.
View detail
![[Repair Type] Clutch Assy](https://img.webike-cdn.net/catalogue/images/59724/03132250_5c890a8c6d1a2_TS.jpg)
Fits: HONDA PCX125, HONDA PCX125, HONDA PCX125, HONDA PCX150, HONDA PCX150, HONDA PCX150, HONDA PCX125
It was a waste of Gold
I should have bought the OEM Product properly
Exchange with the same KN project Belt
I had to put up with it for a thousand miles
Top speed drops 20 km/h Fuel economy drops by 20%
So you're going to get Torque then? Of course, it doesn't answer
This is exactly what it means to be a cheapskate
I've learned a lot
View detail
Fits: HONDA PCX125, HONDA PCX125, HONDA PCX125, HONDA PCX150, HONDA PCX150, HONDA PCX150, HONDA PCX125
performance degradation
The result of being stingy and cheap
The top speed is now 90KM and Limiter is now taken
On top of that, I lost about 10?liters of gas mileage
View detail
Fits: DUCATI SS1000, DUCATI PAUL SMART1000LE, DUCATI MONSTER900, DUCATI MONSTER1000, DUCATI MONSTER S4Rs testastretta, DUCATI MONSTER S4R, DUCATI MONSTER S2R1000, DUCATI ST4, DUCATI ST3, DUCATI ST2, DUCATI SPORT1000, DUCATI Multistrada 1000 2003-06, DUCATI 999, DUCATI 998, DUCATI 749, DUCATI 748
It is better to stop this
Clutch can not be completely disconnected in normal wearing because no flat surface appears even though it is brand new
Because it's bent, I can not run straight with Clutch dragging
I should have chosen a different product, even if I check it on the platen it was a plan accuracy that surpassed the specified value of Service manual to Large width
I managed to take strain and get Clutch to be the largest and grabbed my fingers with 4 fingers Finally I entered Neutral from 1st speed, it was a typical example of cheap worse
View detail
Compatible model, attention!
R is also X 08 - 16 compatible model, but the real thing is X is 08 - 11. I realized later that my WR 250X is 2013 MODEL so it is out of compliance. Because the Pressure plate was quite cool, I cut it a little.. View detail