Reviews
Fits: YAMAHA XSR700, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA CYGNUS Gryphus, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA NIKEN, YAMAHA XSR700, YAMAHA XSR900, YAMAHA NIKEN GT, YAMAHA MT-10, YAMAHA TRACER GT, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-07, YAMAHA YZF-R125, YAMAHA XMAX, YAMAHA YZF-R15
Purchased for USB power supply and power supply for DriveRecorder
To extract power for USB power supply and DriveRecorder for Yamaha BRONCO
Wiring that interrupts and branches to Y's Gear Wire lead2.
The work is very easy, and it is really just a simple installation.
Both USB power supply and DriveRecorder are supplied without any problem.
View detail
For future electrical equipment.
I installed it while servicing my ZOOMER. I had previously installed D-UNIT, a different version of this product, on my ZX-10R, but was attracted by the waterproof specification and compactness of this product, so I installed it on my ZOOMER as well.
I installed it in the position shown in the picture, and the ACC power is supplied from BlinkerWiring. The work itself is not difficult, but if you do not have basic knowledge of electrical systems, it would be safer to ask a shop to do it for you. After installation, check the power with an energizing tester. We are planning to install Fog light etc. in the future.
View detail
Fits: HONDA CBR650R, HONDA CB650R, KAWASAKI NINJAZX-25R-SE, KAWASAKI NINJAZX-25R, KAWASAKI NINJA250R
It does not require processing. It is convenient.
I bought it to pull power to the Steering side.
If you have a little knowledge of electricity, it is easy to make the same thing by normal processing.
I didn't want to cut the wiring, so I bought it because it was inexpensive.
It is branched from the ETC power supply.
Under the Seat, there is a Connector for ETC and a Connector for USB power supply of OEMAttachment.
It is easy to find and install as it is covered and in excess.
Also, the Instruction Manual is not really necessary, is it? It is a small item, but it is extremely detailed.
I will use this to power the ActionCamera at all times.
View detail
For power extraction
I have been modifying my vehicle for course driving, and I would have originally modified Normal Harness and added Relay for power supply of Data logger, A/F meter, water temperature gauge, etc. But Normal Harness is very expensive and I hesitated to modify it, so I bought this one. I have been using the previous model in another car that I own, and it has been working stably and without problems for several years, so I have a good impression of it.
As for requests, I would like to see the Bullet terminal and U-shaped terminals not clamped, but rather a long LEAD wire, and I am a little concerned that the power supply is always open, even though it is located in a secluded place (although it is no problem if tape is applied).
View detail
It can be used for New Model GSX1300R HAYABUSA.
I had a hard time finding information on the power supply removal for the New Model GSX1300R HAYABUSA because there was none.
The location is a White color Connector hidden underneath the RearSeat, so you can easily plug it in here to get power.
View detail
If only it were a little smaller…
If you get one attachment power supply, you can draw four power supplies, which is very convenient for refreshing without messing up the wiring.
I use it on every single vehicle I ride.
It would be great if it were a little smaller.
View detail
Fits: HONDA Rebel300, HONDA CB300R, HONDA CB500X, HONDA REBEL250, HONDA REBEL250, HONDA FORZA-Z, HONDA FORZA-X, HONDA glom, HONDA glom, HONDA glom, HONDA glom, HONDA VTR, HONDA PCX150, HONDA PCX150, HONDA PCX150, HONDA PCX150, HONDA PCX125, HONDA PCX125, HONDA PCX125, HONDA PCX125
Installed on ADV150 Split ACC for USB power supply
Used for ADV150.
Peeling off the Cowling is a challenge, but putting on the product itself is easy because you just plug it in.
Of course, there is no place provided to fix it, so I used Tie Wrap to fasten it.
View detail
Fits: HONDA CBR650R, HONDA CB650R, KAWASAKI NINJAZX-25R-SE, KAWASAKI NINJAZX-25R, KAWASAKI NINJA250R
Attachment power removal
I bought it to take out Attachment power supply for the expansion of Light.
It was possible to install it without any hesitation because it was not installed ETC and there is only one 4-poleCoupler playing under Seat.
I thought that the overall length was a little long because I wanted to make the Wiring simple, but I also thought that the size was just right considering the handling.
Also, I think it may be high in Cost performance as it is probably a WaterproofCoupler to some extent.
View detail
Fits: SUZUKI GSX-R125, SUZUKI GSX-S125, SUZUKI ST250, SUZUKI katana, SUZUKI GSX-R1000
Easy to install, but extremely effective.
Product Name
KITACO KITACO Power Outlet Port Harness
Item Number
756-9000220
Vehicles
GSX-R1000R
Number of man-hours
Ten seconds.
Why did you choose this product?
I bought this because I wanted to be able to charge my phone power from my vehicle.
Impressions after using it
Harness processing is something I've done a few times in the past, so you don't need to use a product to get the power out, but it's more convenient now.
As for work time, only 10 seconds!
It is easy to install because it only interrupts the Coupler for diagnostic equipment.
I don't have to modify the OEM Harness, so if I ever sell the vehicle, I don't have to scratch it.
I usually recommend this product because it saves time and you don't have to think about the troublesome Harness.
▼ Attention
Not particularly.
View detail
USB and DriveRecorder
I am using it by connecting USB power supply and DriveRecorder.
I'm using it in parallel with D-UNIT and so far no problems.
Plus seems to be more user-friendly.
View detail
For securing the power supply for the Dramalecorder, etc.
I purchased this product to install a DriveRecorder.
Because BMW is CanvasSystem, when I take out the power supply unintentionally, it is said that an error message comes out, so I took out the connection of the Attachment power supply from +Wiring of ETC not from Wiring from Lamp.
The body was fixed to the space behind the battery under the seat with Magic tape.
It is possible to take out the permanent power supply and three power supplies, but it is up to 20A in total, so I would like the capacity to be made larger so that it can take out the auxiliary light.
View detail
To expand the electrical components.
At the time of the installation of the water temperature and Oil Temperature Meter&Immobilizer Alarm, I had it installed in consideration of the future expansion of the electrical components.
I haven't installed anything yet, but I was hoping to simplify the installation process a bit.
I haven't added any electrical accessories yet, so I can't say for sure, but I'm hoping it will be easier to add ETC.
View detail
Fits: HONDA Rebel300, HONDA CB300R, HONDA CB500X, HONDA REBEL250, HONDA REBEL250, HONDA FORZA-Z, HONDA FORZA-X, HONDA glom, HONDA glom, HONDA glom, HONDA glom, HONDA VTR, HONDA PCX150, HONDA PCX150, HONDA PCX150, HONDA PCX150, HONDA PCX125, HONDA PCX125, HONDA PCX125, HONDA PCX125
Easy power extraction
I used it to take the Attachment power out of my ADV150.
Just remove the Cowl on the Left Side, take off the lid of the Coupler for the Attachment power supply and replace it with this part.
Because the size of the female side of the terminal of this KITACO did not match with the Bullet Type Terminal of Emon that I used, I replaced the Bullet Type Terminal with the one of Emon after all.
I used the Grip heater for Attachment Wiring, but you can also use Battery Direct Power Wiring. It's very nice and rabbeted.
View detail
review of power supply
Existing power supply was using Emon's 4-poleRelay and branching out Grich USB power supply YOSHIMURAMeter etc.
I installed Fuse on each part and used it, but even if I put Wiring together, it looks bad and the wire from Battery is about 1.25 and thin?
So I put it in.
The result is a good feeling.
Battery mounting wire is thick too.
And it's easy to install, just connect Plus and Minus to Battery.
You can also install a permanent power supply and use it to connect the Battery Charger.
If the length of the mounting wiring is 20-30cm longer, it can be used for various motorcycle
Can I install it in the mounting position?
I think
View detail
Fits: YAMAHA YZF-R3, YAMAHA MT03, SUZUKI Zixxer 250 SF, SUZUKI Gixxer 250, SUZUKI Gixxer 150., SUZUKI GSX250R, YAMAHA SEROW250, YAMAHA YZF-R3A, YAMAHA YZF-R3A, YAMAHA YZF-R3, YAMAHA YZF-R25A, YAMAHA YZF-R25A, YAMAHA YZF-R25, YAMAHA YZF-R25, YAMAHA YZF-R25, YAMAHA YZF-R25, YAMAHA XSR900, YAMAHA XSR900, YAMAHA MT-25, YAMAHA MT-25
AUX wiring harness for XSR900
Initially I though tit would not fit my XSR900 since the wire that comes from the bike has 2-prong leads but this one still fits. One of the leads can be removed and can be used with the Yamaha plug with no issues. View detail
Easy to remove power
I bought it because I can take out multiple power sources when I install DriveRecorder and USB Socket.
Wiring directly connected from Battery is 1 pc and Refreshing.
Fuse is attached to each Wiring, so you can connect it after checking the capacity of Items to be installed, but it seems to be able to support up to 20A in total.
There is an internal Relay, so if you set it to Accessories, the standby power will be reduced to 0 and you don't have to worry about the battery running out.
If the construction of the BodyCase was a little more compact and sturdy, it would be perfect.
View detail
Easy connection.
It is easy to install because it only needs to be branched from the Position lamp.
Because Size of Bullet Type Terminal is thin, there is anxiety about the connection, but it is normal at present.
View detail
Fits: HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA SUPER CUB 50PRO, HONDA SUPER CUB110PRO, HONDA SUPER CUB110, HONDA SUPER CUB 50
without a problem
Because it is only Coupler and the electric wire, I thought that even if I choose an expensive commodity, I chose this commodity which was cheapest. It is OK to install without processing, and I can use it without a problem. View detail
Small processing is required when installing on New ModelHAYABUSA.
[How is it used?
I purchased it for USB Power Port installation of New ModelHAYABUSA.
This is for the GSX-S1000, but the Coupler is the same shape, so it can be used.
Was the one you received as per Image?
The product is as shown in the picture.
How was your experience with it?
The Coupler can be installed as is, so the job is done quickly.
[Points to note]
Because New ModelHAYABUSA is special or the + and - are reversed, it is necessary to replace the terminal before installation.
Precision Driver or mechanical pencil is fine, so you can replace it by just pushing inside the Pin a little.
How did it compare to other products?
There is no particular comparison.
Other items that would be helpful
Point and hang of installation
As I said in the points to note, the + and - are reversed, so just be careful there.
I was able to install the UniversalConnector without any difficulty.
[ITEMS TO BUY TOGETHER
The list which I purchased for installation this time
KIJIMA KIJIMA:304-7150
ACC Branch Harness
https://www.webike.net/sd/22895068/
DAYTONA DAYTONA:98830
Attachment Power Supply Unit D-UNIT (D-Unit)
https://www.webike.net/sd/24050519/
DAYTONA DAYTONA:95444
Mount Kit Multi Bar Holder
https://www.webike.net/sd/23315099/
DAYTONA DAYTONA:92750
Multi Bar Holder Stem Hole Clamp Short Low Type
https://www.webike.net/sd/21846547/
View detail
Fits: SUZUKI GSX-S1000, SUZUKI GSX-S1000F, SUZUKI GSX-S1000F, SUZUKI GSR750, SUZUKI GSX-R1000, SUZUKI GSX-S750, YAMAHA YZF-R1M, YAMAHA YZF-R1 , YAMAHA YZF-R6
If Bullet terminal is included.
The connection is easy for anyone to do because you just need to remove the Coupler of the Tail lamp and interrupt it.
It's convenient because you can get ACC power easily, but it's a pity that you have to prepare Male terminal for the connection side even though it has Female bullet terminal. However, it is a pity that you have to prepare Male terminal for connection even though it has Female terminal.
View detail