Reviews
Useful for Wiring protection and concealment
Useful for concealing and summarizing Wiring
Bend it about 45 degrees toward the uncracked side to open it up and put it in.
It is recommended to install it near moving parts or near the heat source.
This time, I protected the Cable on the front of Camera in DriveRecorder!
View detail
Useful for Wiring protection and concealment
For fine lines, φ3mm is sufficient
Only one Plus wire (ACC power etc.) so it is ideal for protection!
View detail
Fits: HONDA XR250, HONDA CRM250R, HONDA CRM250AR, KAWASAKI KLX125, HONDA CRM80, HONDA XR230, HONDA CRF230F, YAMAHA WR250X, YAMAHA WR250R, YAMAHA SEROW250, YAMAHA XG250 TRICKER, SUZUKI DR-Z400SM, SUZUKI DR-Z400S, KAWASAKI KSR110, KAWASAKI D-TRACKER-X, KAWASAKI D Tracker, KAWASAKI KLX250, KAWASAKI D Tracker 125, HONDA CRM50, HONDA CRF250M
I'm not sure about the electrical system, but ….
I purchased the Racer to make it a public road Spec.
Quantity of electrical components:I could have bought it as a Set, but I bought this one because I can reconfigure it in various ways.
These are the Parts that are required when using LEDs with DRC's Kit.
View detail
Convenient to make it the same color as OEMHarness.
It is convenient to unify the Minus power supply system and Earth system of the retrofit attachments with the Earth system of Kawasaki OEM Harness, Black/Yellow. View detail
Convenient to match the Wiring color of OEMHarness.
It would be helpful to be able to make the color of WhiteHarness, which is equivalent to the Batch+ after the KawasakiOEMHarness junction box, and the Batch+ of the retrofit Attachment, the same White. View detail
Female terminal Cover Only
This is a Female terminal Cover Only product. A separate Female or Male terminal (Male terminal Cover) is required.
Since it is not waterproof, we recommend the purchase of a Waterproof Terminal Set if the connection is to be exposed.
Motorcycle and car Waterproof is rarely seen only in Connector, so I don't think it will be a problem, but it is a good idea to buy it according to your needs.
It is better to have it in Large quantity so that it does not roll around somewhere and disappear because it is a Small item.
Contact between terminals and frames may cause damage to electronic equipment or, in the worst case, cause a fire.
View detail
Reduction in cost with Large volume purchases
Bullet Terminal required for power supply connection for cars and motorcycles.
It is safer to buy more than the required number of units in case of failure.
It is hard to pull out easily when firmly connected, so when pulling it out, grasp the terminal part firmly with a radio pliers or the like.
This product requires Cover and Male terminals as it is Female terminal only.
If you are only going to use a few of them, it is better to buy Bullet Type Terminal Set.
I have never purchased anything other than Emon, so I don't know for sure, but it is best to purchase Male and Female terminals from the same manufacturer.
The Female terminal is recommended to be used on the + (Plus) side since the connection will be covered when the Cover is attached.
View detail
Reduction in cost with Large volume purchases
Bullet Terminal required for power supply connection for cars and motorcycles.
It is safer to buy more than the required number of units in case of failure.
It is hard to pull out easily when firmly connected, so when pulling it out, grasp the terminal part firmly with a radio pliers or the like.
This product is Male terminal only, so Cover and Female terminals are required.
If you are only going to use a few of them, it is better to buy Bullet Type Terminal Set.
I have never purchased anything other than Emon, so I don't know for sure, but it is best to purchase Male and Female terminals from the same manufacturer.
The Male terminal is best used on the ”-(Minus) side because the connection part is exposed even if a Cover is attached.
View detail
Required for Wiring processing
Required Items for connecting Bullet Type Terminal in Wiring
It's priced right, but I think it's necessary and sufficient.
I think it's better to lubricate it because it's not moving well.
View detail
Male terminal Cover Only
This is a Male terminal Cover Only product. Male and Female terminals (Female terminal Cover) are required separately.
Since it is not waterproof, we recommend the purchase of a Waterproof Terminal Set if the connection is to be exposed.
Motorcycle and car Waterproof is rarely seen only in Connector, so I don't think it will be a problem, but it is a good idea to buy it according to your needs.
It is better to have it in Large quantity so that it does not roll around somewhere and disappear because it is a Small item.
Contact between terminals and frames may cause damage to electronic equipment or, in the worst case, cause a fire.
View detail
Soft, flexible and easy to use!
The material is soft and easy to put in and out of the wiring. It is also resistant to deterioration even when exposed to ultraviolet rays! It is easy to use, durable and Large satisfaction! View detail
Hard but strong!
It has a slit in it and you put the wiring inside, but it's just too hard! It is not flexible, so it is hard to put in and take out the wiring, and it is not easy to handle! However, this is one of its strong points and its durability is outstanding! I mainly use it to put together the ETC and sub-computer wiring inside the motorcycle! It is a recommendation because it is very useful if used in the right place at the right time! View detail
The construction is delicate.
[How is it used?
Used for VRDBrake master in GALE SPEED
I purchased this because there is nothing else available.
Just tie it on as it is a regular 2Cable compatible.
Was the one you received as per Image?
As you can imagine.
Purchased with MASTER.
Was the installation difficult?
It's not hard, but tying Cable together is a bit complicated.
How was your experience with it?
It's working normally.
[Included Parts:were they on?
Instruction Manual included
[Was there anything that disappointed you?
Large sturdy at the moment, although it feels fragile.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
I saw that it rusts easily, but I don't know.
View detail
Purchased for Tachometer installation!
With the installation of the Tachometer, we chose the Wiring processed one so that we can use it without any hassle when extracting the electric Pulse!
We are happy to offer a wide variety of Bullet Terminal!
View detail
Fits: KAWASAKI Ninja 250
Used on ninja250
I purchased two of these for use on my ninja250.
The Rubber cap is quite solid and seems to be waterproof, but I think it is better to treat the Harness with insulated Tapeetc.
View detail
Expected
I was concerned about the dim glow of the post-attached (added) Indicator, so I decided to add a rectification Diode.
When I replaced the meter with a Universal one this summer, there was only one warning lamp, so I purchased an LED lamp from KIJIMA and added an Indicator Lamp, but the Red Lamp was glowing dimly. Well, if I didn't care about it, it would have been fine, so I didn't touch it until now, but recently, I decided to add a rectifying diode while reviewing the wiring.
After following the instructions and incorporating it into Wiring, I was able to eliminate the blurriness of the Lamp, but Wiring became so long that it was difficult to store it.
View detail
Used when replacing crf250rallyRear blinker
Used when replacing crf250rallyBlinker
LeftBlinker is Orange.
However, the Minus-side Connector is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
Used for crf250rallyRear blinker
Used when replacing crf250rallyBlinker
RightBlinker is Blue.
However, the Minus-side Connector is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
The texture of pressing the Switch is great.
Since the NSR50 does not have the OEM Kill switch, I installed the Kill switch on the Minus side of the Ignition coil. The quality of pressing the switch is much better than the cheap ones made by Chinese manufacturers! The only thing is that the price is a little bit expensive for MinusPoint. View detail
Pricey but convenient for beginners
I think it is very convenient for amateurs to connect Motorcycle wires such as Blinker or Tail lamp. First, strip the cord, twist the wire that appears, insert it into the hole in the plastic part of this Connector, and snap it with pliers or something, and you have One Side. Do the same for the other side. The finished products are made of Male and Female, so you can connect them properly by plugging them into each other. It is an excellent product. However, if it is difficult to connect the wires, it is of course useful, but if you have a spacious place and have some room in length, I think it is best to put a solder on it.
The price is high and the cosmetics are not so good. But I think it's useful if you're in a hurry, a very beginner, or in a small space.
View detail