Reviews
Useful for Wiring protection and concealment
Useful for concealing and summarizing Wiring
Bend it about 45 degrees toward the uncracked side to open it up and put it in.
It is recommended to install it near moving parts or near the heat source.
This time, I protected the Cable on the front of Camera in DriveRecorder!
View detail
Useful for Wiring protection and concealment
For fine lines, φ3mm is sufficient
Only one Plus wire (ACC power etc.) so it is ideal for protection!
View detail
Female terminal Cover Only
This is a Female terminal Cover Only product. A separate Female or Male terminal (Male terminal Cover) is required.
Since it is not waterproof, we recommend the purchase of a Waterproof Terminal Set if the connection is to be exposed.
Motorcycle and car Waterproof is rarely seen only in Connector, so I don't think it will be a problem, but it is a good idea to buy it according to your needs.
It is better to have it in Large quantity so that it does not roll around somewhere and disappear because it is a Small item.
Contact between terminals and frames may cause damage to electronic equipment or, in the worst case, cause a fire.
View detail
Reduction in cost with Large volume purchases
Bullet Terminal required for power supply connection for cars and motorcycles.
It is safer to buy more than the required number of units in case of failure.
It is hard to pull out easily when firmly connected, so when pulling it out, grasp the terminal part firmly with a radio pliers or the like.
This product requires Cover and Male terminals as it is Female terminal only.
If you are only going to use a few of them, it is better to buy Bullet Type Terminal Set.
I have never purchased anything other than Emon, so I don't know for sure, but it is best to purchase Male and Female terminals from the same manufacturer.
The Female terminal is recommended to be used on the + (Plus) side since the connection will be covered when the Cover is attached.
View detail
Reduction in cost with Large volume purchases
Bullet Terminal required for power supply connection for cars and motorcycles.
It is safer to buy more than the required number of units in case of failure.
It is hard to pull out easily when firmly connected, so when pulling it out, grasp the terminal part firmly with a radio pliers or the like.
This product is Male terminal only, so Cover and Female terminals are required.
If you are only going to use a few of them, it is better to buy Bullet Type Terminal Set.
I have never purchased anything other than Emon, so I don't know for sure, but it is best to purchase Male and Female terminals from the same manufacturer.
The Male terminal is best used on the ”-(Minus) side because the connection part is exposed even if a Cover is attached.
View detail
Required for Wiring processing
Required Items for connecting Bullet Type Terminal in Wiring
It's priced right, but I think it's necessary and sufficient.
I think it's better to lubricate it because it's not moving well.
View detail
Male terminal Cover Only
This is a Male terminal Cover Only product. Male and Female terminals (Female terminal Cover) are required separately.
Since it is not waterproof, we recommend the purchase of a Waterproof Terminal Set if the connection is to be exposed.
Motorcycle and car Waterproof is rarely seen only in Connector, so I don't think it will be a problem, but it is a good idea to buy it according to your needs.
It is better to have it in Large quantity so that it does not roll around somewhere and disappear because it is a Small item.
Contact between terminals and frames may cause damage to electronic equipment or, in the worst case, cause a fire.
View detail
Expected
I was concerned about the dim glow of the post-attached (added) Indicator, so I decided to add a rectification Diode.
When I replaced the meter with a Universal one this summer, there was only one warning lamp, so I purchased an LED lamp from KIJIMA and added an Indicator Lamp, but the Red Lamp was glowing dimly. Well, if I didn't care about it, it would have been fine, so I didn't touch it until now, but recently, I decided to add a rectifying diode while reviewing the wiring.
After following the instructions and incorporating it into Wiring, I was able to eliminate the blurriness of the Lamp, but Wiring became so long that it was difficult to store it.
View detail
Pricey but convenient for beginners
I think it is very convenient for amateurs to connect Motorcycle wires such as Blinker or Tail lamp. First, strip the cord, twist the wire that appears, insert it into the hole in the plastic part of this Connector, and snap it with pliers or something, and you have One Side. Do the same for the other side. The finished products are made of Male and Female, so you can connect them properly by plugging them into each other. It is an excellent product. However, if it is difficult to connect the wires, it is of course useful, but if you have a spacious place and have some room in length, I think it is best to put a solder on it.
The price is high and the cosmetics are not so good. But I think it's useful if you're in a hurry, a very beginner, or in a small space.
View detail
Frosted Material with high texture
I used this product to wiring up my Ninja250SL's sub-computer and USB. Honestly, you can use Curing Tape instead of this product, but this product is pre-cut, so it is easy to work with, and it looks overwhelmingly good, so it is a Recommendation! View detail
Finally, it's time to go.
I purchased and installed a Push Type Switch to use as a switch for the power supply of the car navigation system, but the other day, when driving on a mountain pass with somewhat rough pavement, a malfunction occurred due to vibration, causing the power supply to turn off and on, and temporarily Navigation repeatedly started up and stopped functioning.
This symptom did not occur during normal city driving or on well-paved roads, even on mountain passes, so I think that the problem may have been caused by severe vibrations that exceeded the manufacturer's expectations. I think that the previous Push Type Switch may not be good at strong vibrations. I don't want to continue to use the switch in this situation and have navigation problems, so I decided to replace it with a toggle switch that I have and see how it goes.
I bought this toggle switch but never had a chance to use it, so it has been sitting in my inventory for a long time. I haven't tried it in a place where it would vibrate yet, so I don't know how it would work in a similar situation, but I like the way it looks, so I'm glad it works.
It is not waterproof, but since we basically don't ride in the rain and it is installed in a Cowl, it is probably Large sturdy. I have applied waterproof treatment to the terminal part.
View detail
We are running low on inventory.
This is a necessity when playing with Motorcycle and car electrical components. I recently purchased this Bullet Terminal because the stock of Bullet Terminals was running low when I was reviewing the wiring for my Motorcycle's retrofit electrical components.
I don't like to have to stop working when I run out of materials, so I try to stock up on materials that I use frequently, so when I buy Large quantities, I buy these quantities. In this case, I purchased both Male and Female at the same time.
Some of the No Brand products were inferior, but I can buy Emon products with confidence. This time, too, there were no defective products among the 100 items.
View detail
By Location!
When wiring, Wiring Tube is used for the wiring itself, and Coil type Wiring Bando is used for the Bullet Type Terminal and the Jack portion. The Wiring type is easier to use than the Tube type for these joints because it is easier to remove immediately. View detail
Wiring Summary!
The Wiring Tube is a good product for refreshing the wiring, because it is hard to tell which is which when you're wiring and it can cause stress buildup. View detail
Wire standards
Both EmonAV1.25sq and DAYTONAAVS1.25 are probably stranded wires, but Emon has a thicker and softer coating, while DAYTONA has a thinner and harder coating, which is said to be similar to OEM harness. Incidentally, "sq" stands for "Square," and "AWG" is called "Gauge" (AmericanWire gauge) in the United States wire standard, indicating the cross-sectional area of the conductor section. AWG16 = 1.25sq = 1.31mm2. The larger the AWG number, the smaller the cross-sectional area. If it is just 1.25 and only a number, it may be the diameter of the conductor, but is there any diameter notation for stranded wire? View detail
Very inexpensive.
I would like to install a new Grip heater, but I would like to calculate if the heater is Large enough to interrupt the wiring between the USB port and the Relay. The maximum charge current of the two electrical components is 3.3A at 13.5V for the Grip heater and 4.8A at 5V for the USB2 Port (5V is switched on and off), totaling 8.1A. I bought Emon's AV1.25sq. The available power is 140W or less for 12V cars and 280W or less for 24V cars. If converted to allowable current, it is about 11.6A? Although it is within the allowable range, it is not as high as DAYTONA's AVS1.25 (A) of the same size.:Auto for Vehicle Low Voltage Power Line, V:Vinyl、S:The price is 1/8th of DAYTONA in unit length, and Emon is very cheap. By the way, it is another Wiring, but the most large current of ETC on-board unit seems to be less than 1A because it is 1AFuse, although only standby current was written. View detail
I can make it myself.
Purchased to branch power from existing Bullet Terminal.
You can make it yourself if you want, but since it is a power supply, you need to use something like this in case of emergency.
One drawback is that the Wiring color is Black.
Since it is Body ground, it is basically Plus where these things are needed.
I wrapped Red Vinyl Tape around the Wiring.
View detail
I haven't seen needle GoldHanger lately.
I purchased this product (adjusting for shipping costs) for the installation of a car's driver's recorder.
In the past, we have extended the needle GoldHanger and used it as a substitute when passing through Wiring for installation of Motorcycle's driver's record, etc. Recently, however, the needle GoldHanger itself is not seen very often.
This is convenient for playing with electrical equipment because it is properly insulated and can be easily passed through tight spaces by passing the Wiring through the Wire loop. The needle is not as hard as GoldHanger and is easy to use. It is not expensive and should be kept in your tool box.
View detail
One of these will do the trick!
Used to make Bullet Type Terminal when installing Grip heater on REBEL250.
Was the one you received as per Image?
We chose this product because there are parts for various terminals other than Bullet Type Terminal, and there is no need to purchase additional parts.
As for the pliers, I think they are adequate compared to the more expensive ones, but I think this is fine for first-time users or one-time trial users.
How was your experience with it?
There is a video QR code on the Package for installation instructions, so we worked while watching the video.
I felt that it was the first time or that shimmying was moderately difficult.
[Points to note]
Watch the video a couple of times and do it when you have time.
How did it compare to other products?
Many pliers alone cost about the same price, so I think it is a good deal to have the terminal parts included at a low price.
View detail
Used for Wiring on Motorcycle navigator!
It is long enough and strong enough not to break. The colors are good, and above all, it is very inexpensive!
It's Recommendation!
View detail