Reviews
A little high-end light bulb
Used for LITTLE CUB.
In fact, the same shape MH Pine Stripe" I bought it at the same time as the Valve made by The Matsu Stripe Valve was purchased at Webike for less than $500. This product is almost twice as expensive as Matsu Stripe's at the regular price. The actual price is around 700 yen. I was curious to see how this 200 yen difference would affect the performance, so I bought two types for spares.
This Hyper Bulb is as bright as Halogen! This Hyper Bulb was included in the Package because of the CatchCopy that says "Brightness as bright as Halogen!
I expected it to be brighter than FuTwo's Pine Stripe.
The results of the comparison experiment are ・・・・ close!
Comparing the brightness of the projected area on the wall in a dark room, it might be brighter than that of a normal white light bulb, if you ask me. It was an impression that the light was brighter than that of a normal white light bulb.
Either way, it is inexpensive, so it is a good idea to go with Stanley (this product) in the hopes of getting One Upgrading!
The higher-end product is Halogen, but it costs around 1,500 yen, so I feel that this one, which is half the price of Halogen, is sufficient.
The Stanley was made in Thailand, and the cheaper MH Matsu Stripe was made in Japan.
View detail
LED for Sphere LightMotorcycle
It is bright and nice for the price. I would buy it again next time. View detail
Fits: HONDA DJ-1, HONDA DJ-1R, HONDA DJ-1L, HONDA DJ-1RR, HONDA NSR50, HONDA NSR50, HONDA XR50 MOTARD, HONDA Express, HONDA CAREN S, HONDA GYROUP, HONDA GYROX, HONDA GYRO CANOPY, HONDA JUST, HONDA JULIO, HONDA JOY, HONDA GIORCUB, HONDA Giorno, HONDA GIORNO DX, HONDA SQUASH, HONDA SPACY50
Headlight LED
Installation was easy. It was brighter than I expected. View detail
This is a review of the headlight rim.
When installing, it is installed on top of the original rim. Suitable for CT125. It is a 3m tape fixation type, so please replenish it enough before installation.
It's a minor tuning, but those who recognize the CT125 will immediately recognize the small change.
I think the price is reasonable too. It would also be a good idea to be careful in case of rain. I think it would be better to install the headlight guard on top of the rim after installing it.
Recommended! -------------------------------------------------- -------- It is a structure installed on the pure rim when installing. Suitable for CT125. 3M tape is fixed and please supplement it more enough. It's a trivial tuning, but if you look at CT125, you can find out at a small change. I think the price is also appropriate. It would be nice to be careful about rainy weather. After installing the rim, it would be better to install the headlight guard on top of it. Recommended! Powered by Google Translator
View detail
It looks good, but the light leaks.
I have a TT250R, but the light is too dark (like a moped) and the face is a little too much, so I changed to this one which is cheaper and has a headlight.
Installation is as simple as using an Elastic band and tying it to the front fork, but of course the coupler on the Headlight will not fit, so it may be difficult for someone who can tinker a bit.
Headlight Bulb is one of the objectives as it also fits H4 Light Quantity Up】 【Light Quantity Up I personally think that Parenthesis is good with a Small face and the NORMAL look is gone.
Minus point is light leakage.
As you can see in the picture, the headlight leaks quite a bit around the meter. Also, there is no Instruction Manual, so it may take some time for motorcycle beginners to understand.
Well, it is cheap, so overall I am Large satisfied!
View detail
This is a purchase review.
Usually, many people decorate the front part by using a front carrier / ambulance / headlight protection device.
However, for those who don't use it for og looks or off-roading, I think a simple headlight replacement can be a big help in changing their image.
The price is expensive. I will have to use it more and decide whether it will rust due to water. -------------------------------------------------- -------- Usually, many people are decorated by using the front career / ambulance / headlight protection mechanism. However, for those who do not use OG or off-road, I think it is a great help to change the image by replacing simple headlights. The price is expensive. I should try more and judge if it is not rusted by water. Powered by Google Translator
View detail
Fits: HONDA CROSSCUB110, HONDA CROSS CUB50, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB 50, HONDA SUPER CUB 50
I have tried to install it on the CUB but...
I was given a pair of Smoke Blinker Lenses and installed them, so I purchased these lenses for a sense of unity and dress-up.
When the car stops, everything is [Color] Smoke gives a sense of unity and enhances Parenthesis.
However, unlike the Blinker, the Motorcycle's BrakeLight lights up along with the Headlight when the key is turned on and the Engine is ignited.
Although it was darker than OEM, it wasn't as disappearing as the car, so it was half as effective...
In the strong light when I put Brake on, it looks more like Pink than Red...
I guess I was a little disappointed for the price.
However, since it is a Mukawa, the texture and precision of the objects are unquestionably good.
View detail
Small work is required for installation.
We replaced the headlight with LED to cover the power consumption of electrical components in winter. I have not driven at night yet, so I do not know how much brighter the headlight is, but I could feel that it is much brighter during the daytime. The optical axis also seems to be large and strong.
The only thing to note is that the Controller and Coupler will not fit in the Bonneville 120 Headlight case.
I installed it on the Headlight BracketReverse side.
View detail
Fits: HONDA CT125CT110 HUNTER CUB, HONDA CT125CT110 HUNTER CUB
Excellent for OEMHeadlight measures that are too dark.
I purchased this product to address a complaint about the CT125, the OEMLED Headlight.
It would not be bad to install a Fog Lamp instead of a Driving Lamp, but the generator output is also equivalent to the Engine Displacement Volume, so it is not possible to install an oversized electrical component. I have just added an Asahi Leg shield, so it's even more difficult to install it in the right position.
And as a compensatory act for not having the usual time to rideω.
Order this kit to convert OEM LED Headlight to H4, which is critical for nighttime rain on country roads, as the visibility is almost ineffective.
Kelvin is color temperature, not brightness.
I think the work itself is reasonably difficult, but there are too many accessories in my house, so it is somewhat more difficult to access and remove them….
Also, I'm so paranoid that I ignore the work as per Manual and processω.
First, we temporarily assembled the tap to check that it works, and then discarded the Electro Tap without regard to the manual.
Good thing good kids never use Electro Tap.
Because Trouble Frequent Cancer
The core wire is exposed by stripping the intermediate sheath, the plug receptacle is cut open with an electric tool to make an improvised splice, crimped with a branch line, and wrapped with harness tape.
With this, the contact failure rate is as close to 0% as possible!
And the rest is usually as per Manualω.
Left Handlebar Switch cut to HandlebarRight from Triple treeReverse side
Body ground is from the base of the Triple treeLeft reflector.
It was recommended to drill holes on the reverse side of the resin case….
I had a woodworking holesaw, so I managed with that.
If you don't have one, I'd use a soldering iron to melt it down.
One last move!
The H4 is a very good solution, but it has a LED headlight that lacks the universal nature of the fine connector with a dedicated cooling fan, so it is not a good solution.
When it becomes impossible to light up in the future….
Branch Wiring to UniversalH4-305Connector for immediate replacement
Bullet Terminal connection in the middle and keep the Connector inside the very narrow Headlight case.
Of course, the Bullet Terminal should be on the Female side and insulated with harness tape just in case.
Incidentally
Kit side Harness
White GND(Earth) − CouplerReverse side Left
Yellow−Lo − same Up
Blue−Hi − the same Right
This way, whether Halogen or LED, Universal Product can be used.
However, the use of High Wattage products such as Halogen etc. should be avoided as much as possible.
I think LED is better for Halogen 35w or so.
Carry H4-305Coupler and spare H4LED
There is also a position lamp in the headlight, but ….
No Wiring because even 5w is too close.
Also, if the Wiring fixed Band in the Case was still used, it was not closed and was not established, so it was disconnected and the internal Wiring was set to "Quantity".:Pair (for Left and Right) allocated to
GreenWiring to the Controller is also a + line, so I ran it through the MeshWiringProtective Tube.
By the way, processing will likely make the warranty ineffective, but ….
For me personally, as long as I make sure that there are no problems with the initial operation, I'll be fine.
I honestly don't care.
I'd rather have my hands tied
I think it would be much better to customize it in a way that makes sense in front of you.
I've only assembled and lighted test.
It is a world of difference from OEM daylight lamps!
It's triple the number of Watt ….
I'm told the Tester figure is 29,800 candela.
It doesn't look so bad either….
It's an internal Wiring or Headlight, but it's an Aluminum ultra-thin wire.
I have some concerns about the quality of the product.
I'm an old person ω.
View detail
Required when replacing LED BlinkerHolder
[How is it used?
When replaced with Active's LED BlinkerHolder, the Holder with the OEM Blinker Bracket is no longer needed.
The installation is fine with Bracket as it is, but it leaves unnecessary holes and does not look very good.
Was the one you received as per Image?
The packaging is easy to use, with minorSmall scratches, but no problems with use.
Was the installation difficult?
It is very easy with tools.
The LED License Plate Lamp is made of resin and can be easily broken if tightened too strongly.
It can be broken unexpectedly easily, so be careful, especially if you are a strong person.
How was your experience with it?
Refreshing around the Rear more.
[Opinions and requests to Manufacturer
If you put a Holder, LED Blinker Holder, with Reflector, RearCamera Bracket, License Plate, … and many other things, it will be very thick.
At least Reflector is the same bodyQuantity:I would like to have something that can be attached with 1pc.
View detail
UniversalBlinker.
I purchased the Jixxer 250 for rounding Light.
I wanted to create a Retro feel, so instead of the sharp Type of LEDs.
We went with the old-fashioned Light Bulb Type.
I felt the kindness of the Manufacturer in the 10W and 15W bulbs included.
View detail
Transferred from Sphere
[How is it used?
It is used on MainMotorcycle's XJR1300C.
I used to use H4LED bulbs from Sphere Light, but after about 2 years of use, they stopped lighting up and...
When I took it apart, as you can see in the picture, the root part had been torn off due to heat.
The Seal appears to have become soft and brittle due to heat.
Was the one you received as per Image?
This is actually my second DAYTONA. I also used Sphere, but DAYTONA's quality of detail is better.
Was the installation difficult?
It is easy because it is the same as a normal Valve replacement.
How was your experience with it?
The brightness is perfect. I think it is brighter than Sphere.
but the optical axis was slightly gapped and needs to be adjusted.
By the way, the Sphere passed inspection.
[Included Parts:were they on?
Included Parts:Not available.
[Was there anything that disappointed you?
Not particularly
View detail
Simple&Compact
[How is it used?
I bought a used WR250R a few years ago with a Fender Eliminator Kit from Other Brand Product.
The Fender Eliminator itself was fine, but in my opinion, it had a tail lamp that was not suitable for the vehicle, so I purchased this product to replace it.
Did you receive the item as per the Image?
The product received is more Compact and thinner than I expected, and depending on the position setting, it looks I don't think the tail lamp is installed!" The product was so large that I felt it was more than Image could provide.
Was it difficult to install?
The functional aspect of the Lamp is completed when the originally installed Bullet Type Terminal for connection is removed and connected to each.
My WR250R has Other Brand Product's Tail lamp as mentioned above, and it was originally Bullet Type Terminal connection, but I replaced the Bullet Terminal on the product side because the terminal size was a little too large. 1 pc is Grounding Wire (Black) I can't remember which is which... sorry.
The Fender Eliminator can be installed without any modification because the holes were aligned well with the original holes for installing the Tail lamp.
If you buy the OEM type connector for each manufacturer sold by KITACO and connect Wiring, Wiring will be refreshed and you can easily return to NORMAL when you want to. If you want to return to NORMAL, you can easily do so.
How did you like it?
The Tail lamps are fixed in a safe position because they can be involved in unexpected accidents such as rear-end collisions when driving on public roads if they are not clearly visible. (I have a friend who says that I am over-refreshing...) I personally have nothing to say.
Was "Included Parts:" attached?
It is a very Simple product with all the product images shown in Webike's product section.
Were there any disappointments?
Not at all.
Because of the low price, I was worried that the LED bulbs would burn out, but they have been functioning without problems for several years since they were installed.
Other items that would be helpful
Point and hang of installation
If you want to process Wiring as beautifully as OEM, use the OEM Type Connector by Manufacturer as described above! (Since this is a personal judgment, those who are fine with Bullet Terminal can leave it as it is, but since it is an insulated tape, please make sure to perform waterproof treatment.) 。
[Availability and clarity of the Instruction Manual
electrical system (?) I think this is a very straightforward product for the
[Notes]
Nothing in particular, just be careful not to misplace Wiring?
[ITEMS TO BUY TOGETHER
As I mentioned above, this is also available from KITACO and other companies. OEM Type Connection Terminals by Manufacturer will allow one-touch connection to Harness on the car body side.
Since the method of fixing to the car body varies depending on the car model, it may be better to try a temporary assembly before full-scale installation.
First, check the fixation method by placing it on the vehicle in which you want to install it.
[Opinions and requests to Manufacturer
The price is low and the product is Compact, so it is a highly universal product.
View detail
Fits: HONDA DIO FIT, YAMAHA JOG, YAMAHA JOG Zr, YAMAHA YV50 Z II, YAMAHA JOGREMOTE CONTROLLER, YAMAHA Axis Treat125, SUZUKI ZZ, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125G, SUZUKI LETS II, SUZUKI LETS IIL, SUZUKI LETS IICombination brakes, YAMAHA JOG, YAMAHA JOG Zr, YAMAHA JOGDX, YAMAHA JOGPetit, YAMAHA MATE50, YAMAHA MATE50D
LED is still bright
We replaced Halogen with this product.
I feel that there are fewer opportunities to be forcibly interrupted at night than before.
View detail
Fits: SUZUKI ADDRESS V125, KAWASAKI KSR110, HONDA PCX125, HONDA MONKEY, HONDA APE 100, HONDA GORILLA, YAMAHA CYGNUS X (FI), HONDA APE 50
Used for CUB90
CUB90 is equipped with external Tachometer, various sensors, USB power supplyCoupler, and LED on the Tail to reduce battery load.
The bulb power consumption of the NORMAL is 15W/8 and the LED is 21W/5. The LED is not labeled in Lumen so I did not know how bright it was but I trusted Brand.
The large size is a little smaller than a light bulb, the bracket is in good condition and the tail lens has not been hit.
I read that it was a little dark in the impressions, so I cleaned the tail lens and put aluminum tape on the tail case, which is an old-fashioned way of doing things.
The Tail Chica-Chica is a little bit when the Idling is on. Stop-lamp is powered by battery, so it does not ChicaChica. The light is bright enough to pierce your eyes at some angles.
When the Lens is turned on, the ChicaChica of the Tail is not felt. The brightness of the Tail is about two-thirds that of the bulb, and the Brake is about the same or slightly stronger than the bulb, which is fine.
Tail is AC so ChicaChica is not an option but I don't know how it is for the life of the LEDs. I have been using it for about 6 months and so far no problems. I remove the Lens every once in a while, but it is not burnt or deformed.
After installation, the charging voltage did not change during idling. Battery load seems to be decreasing. I think it can go as it is.
View detail
bright
Halogen, I was dealing with, it is quite bright, Kojuk, Large was strange until I put it out! View detail
Fits: HONDA Dunk, HONDA Sh mode, HONDA Giorno, HONDA BENLY50, HONDA CROSS CUB, HONDA BENLY50110, HONDA DIO110, HONDA glom, HONDA FORZASi, YAMAHA VOX, YAMAHA VOXDELUXE, YAMAHA VOXLIMITED, YAMAHA GEAR, YAMAHA NEWS GEAR, YAMAHA VINO, YAMAHA VINODX, YAMAHA VINOMolar feh, YAMAHA SDR, YAMAHA MAJESTY, YAMAHA MAJESTYC
It is easy to install.
The white light of LEDs feels bright.
It will probably have a long lifespan, so it will be cost effective.
Replacement was the same as a normal Valve replacement.
View detail
LED Conversion of Old Motorcycle
The old Filament bulbs were replaced with LEDs. I would like to see a newer design, but I guess that's impossible because of the age of the car. The installation is easy and I am generally satisfied. I am dissatisfied with the high price.
The image is when Brake is lit.
View detail
Equipped on SR500
I put it on anyway.
Wiring does not fit into the light case, so some ingenuity is required.
View detail
I wanted a little more brightness.
Brightness is still proportional to the Gold amount. View detail