Reviews
Useful for Wiring protection and concealment
Useful for concealing and summarizing Wiring
Bend it about 45 degrees toward the uncracked side to open it up and put it in.
It is recommended to install it near moving parts or near the heat source.
This time, I protected the Cable on the front of Camera in DriveRecorder!
View detail
Fits: Others
easy to read
Can be installed in the middle of the Handlebar Clamp
It was easy to install
Easy to check voltage, oil temperature, clock, and
I think it's a good product
View detail
Useful for Wiring protection and concealment
For fine lines, φ3mm is sufficient
Only one Plus wire (ACC power etc.) so it is ideal for protection!
View detail
VINO125
The size and shape were the same, but a little cutting work was required, so if you have the tools, you can install it on the VINO125! View detail
exchange
I managed to attach it successfully by replacing only the cover. View detail
It is easy to install.!
OEMHalogen was replaced because it was too dark.
Installation is a simple matter of removing and replacing the OEM. I did a test run during the daytime, and it was a little brighter in the Tunnel. I don't drive much at night, so no problem! I don't drive much at night, so no problem! I don't know about durability, but I'm happy with JAPAN, it's well made and looks good.
View detail
It does not require processing. The lid is a bit ….
The USB power supply can be removed very easily if you don't feel the need to remove the front parts, which are the face of the motorcycle. If you don't feel that removing the front parts and drilling holes in the body is too much work, you can take out the USB power supply very easily.
It is not difficult if you have a set of tools used for maintenance. Drilling was done halfway using a plastic cutter, Nipper, and File.
Wiring is completed by simply joining the existing Connector, which is the quintessential OEMAttachment.
It is also helpful to be able to download the illustrated Instruction Manual.
Material for Waterproof:It has a rubber lid, but the fit is squishy and unreliable, and it hits a nearby screw when closed, so it's not great here.
Aside from the amount of work and quality, I wonder if the most appealing feature of the Large is the ability to take out the USB power supply without any wiring process.
For reference, it took about 2~3 hours to do the work by hand.
View detail
Fits: Others
The Connector part is Compact, but the Body box is in the way.
As a result of changing Navigation from 5-inches to 7Inch, when connecting Navigation power to the USBConnector on the BOLT Shoulder Bag
It became difficult to do, so I thought it would be a good opportunity to replace it with this product, which is 2.4A compatible.
As mentioned in the Title, the Connector is compact and unobtrusive, but the Body (transformer from 12V to 5V?) is not. However, the Body (transformer from 12V to 5V?) is
I was worried about the mounting position because it is bulky.
Finally, it is fixed with Double-sided Tape on the Front side of the Top Bridge, which is hidden by the Bullet Cowl.
Red wiring is very noticeable as it is, so the Bullet Terminal is cut out and soldered on.
Spiral Tube and Wiring Cover were used to prevent the Red color from being seen.
The Connectors placed on the Handlebar are Compact and unobtrusive, so they look good when not in use.
View detail
Fits: HONDA CB300R, HONDA CB125R, HONDA CB250R
It's difficult, isn't it?
I put Meter's Film on the new car.
I thought it was no different than GlassFilm for cars.
He applied it with a mild detergent.
Eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee dust ・・・・ tears
That's a tough one.
I wouldn't worry too much about it since it's for Meter Protection purposes.
Fortunately, it is expensive and contains two different types of films.
I'll try again next time.
You must be a PRO to be able to do this so beautifully.
View detail
Classic color and cool!
I installed it on my JA07SUPER CUB and it looks great with the classic color! And the Yellow Bulb is easy to see even in the rain! I like the durability and the fact that it doesn't break easily! I am very pleased with the durability of the bulb and the fact that it doesn't get damaged easily! View detail
USB Socket plugged in...
I think the slide style cap is great in terms of both gimmick and operation. However, since the SocketBody and the middle box are of a certain size, I could not pass through the small space around the Handlebar to hide the Wiring, and I had no desire to make it all Rose, so I ended up compromising. In this respect, it might be better to have an intermediate connector like other manufacturers, but it might cause contact failure, so it is a win-win situation.
The included parts are sufficient for most motorcycles, but a plain type terminal would have been a nice addition.
Test after installation is completed (using Anker USB Cable) After repeated unplugging and plugging several times, we were able to confirm that the device was energized. There was a feeling of being stuck until the device was energized, so there may have been something wrong with the molding of the USB Socket.
In any case, we are satisfied that the system is currently fully operational.
View detail
Horn.
I purchased the Racer to make it a public road Spec.
Quantity of electrical components:I could have bought it as a Set, but I bought this one because I can reconfigure it in various ways.
If you energize it and turn on the Switch, you can use it normally.
The volume is also sufficient.
View detail
Should be originally equipped with OEM
It is a must have item for a beginner of Rotary Mission. I used Seiran Kobo's Meter Holder for the Handlebar Post because it is too far away from the Meter and not very visible. The instruction manual is easy to understand with color photos. Sometimes when I put it in first gear... "0" Neutral on the Meter side disappears, so I judge it by that. View detail
Fits: HONDA XR250, HONDA CRM250R, HONDA CRM250AR, KAWASAKI KLX125, HONDA CRM80, HONDA XR230, HONDA CRF230F, YAMAHA WR250X, YAMAHA WR250R, YAMAHA SEROW250, YAMAHA XG250 TRICKER, SUZUKI DR-Z400SM, SUZUKI DR-Z400S, KAWASAKI KSR110, KAWASAKI D-TRACKER-X, KAWASAKI D Tracker, KAWASAKI KLX250, KAWASAKI D Tracker 125, HONDA CRM50, HONDA CRF250M
I'm not sure about the electrical system, but ….
I purchased the Racer to make it a public road Spec.
Quantity of electrical components:I could have bought it as a Set, but I bought this one because I can reconfigure it in various ways.
These are the Parts that are required when using LEDs with DRC's Kit.
View detail
Convenient to make it the same color as OEMHarness.
It is convenient to unify the Minus power supply system and Earth system of the retrofit attachments with the Earth system of Kawasaki OEM Harness, Black/Yellow. View detail
Convenient to match the Wiring color of OEMHarness.
It would be helpful to be able to make the color of WhiteHarness, which is equivalent to the Batch+ after the KawasakiOEMHarness junction box, and the Batch+ of the retrofit Attachment, the same White. View detail
Cable is hardened
Cable is thicker in terms of current capacity.
Attachment power supply cable is protected by a Shrinkable Tube together, and I wanted it to be separated anyway.
The body is surprisingly large because it contains fuse, so it is difficult to place it in the right place.
View detail
Fits: SUZUKI GSX-S125, SUZUKI GIXXER 250, SUZUKI GIXXER SF250, SUZUKI GSX-R125, SUZUKI GIXXER 150, SUZUKI V-Strom250 SX
Extension Harness Min.
Quantity of 1 Set for 1 Vehicle to install TRL2Blinker:Set.
TRL2 LED Blinker*4
Mount for TRL2*4
Extension Harness (long)*2
Extension Harness (short)*2
MicroIC Blinker Relay*1
Small and very Stylish
The mounting is done by sandwiching the Mount with the Plate, and since the hole is small, the Bullet Type Terminal is inserted while shifting it slightly.
The price is almost the same if you buy them individually, but you save money for the Extension Harness.
The included MicroIC Blinker Relay is about the size of a small finger, so you should have no trouble finding a place to place it, but the terminals are bare, so be careful not to touch the Gold Genus.
View detail
From Halogen to LED
The installation itself is easy, but it was very Large strange to fit it inside the Headlight.
Headlight floated and was very hard to close. I had to adjust the Wiring many times, and after pushing it in with a lot of effort, I couldn't close the Screw by myself and had to ask my family for help. I wonder if the Wiring I pushed in is Large sturdy… Spring was used as OEM.
View detail
Fits: HONDA APE, HONDA BENLY50, HONDA DAX, HONDA MONKEY, HONDA CT110 HUNTER CUB, HONDA GB250 CLUBMAN, HONDA FTR223, HONDA CL400, HONDA FTR220, YAMAHA SRV250, YAMAHA RENAISSA, YAMAHA BRONCO, YAMAHA TW225, YAMAHA TW200, YAMAHA SR400, YAMAHA SR500, SUZUKI VANVAN, SUZUKI GN125, SUZUKI GS125, SUZUKI VOLTY
Blinker replacement
Replacement was easy, but the Valve needed to be replaced because it was a high flasher. View detail