Reviews
Since M5.
I bought it because my homemade Fender Eliminator cracked when it was brittle.
I chose this one because Screw was M5.
It is a very normal reflector with no particular problems.
View detail
If you think you're missing something...
Almost done with TW's Restore and put a Number on it.
Hmm I don't know. It's not enough.
No Reflector Sweat
I don't think I'd be caught without it.
tentatively
I feel like I've become cool.
View detail
Simple configuration
[How is it used?
Since the Fender Eliminator Kit was relocated, the Reflector that had been used until then could no longer be used, so we chose this one with the License Plate co-tightening type.
Similar products are available from Active and KIJIMA etc., but I chose DAYTONA's because it was in stock and inexpensive.
Was the one you received as per Image?
It was just like the picture.
The condition of the paint was also fine.
Was the installation difficult?
Replacement is easy as it is simply tightened together with the bolt on the License Plate.
One Side at a time, you can remove the Bolt and slip it into the gap and not worry about dropping it.
How was your experience with it?
Naturally, it was Exactly to the Size of the License Plate.
Visibility is also sufficient.
The Cushion works well and the contact with the Number is just right.
[Included Parts:were they on?
Mount, Reflector and anti-vibration Cushion are included.
[Was there anything that disappointed you?
Not particularly
【Review】
It is an inexpensive and solid reflector when converted to a Fender Eliminator Kit.
Of course, it also passes vehicle inspections, so it is safe for vehicles that are subject to inspections.
View detail
It reflects beautifully!
I purchased this product to increase safety as I drive more at night and use it attached to my Rear Fender. I think it contributes to safety because of its beautiful reflection. It is easy to process and can be cut into any shape you like. I also put it on the color cone in my garden. It can be used in various places, so I can recommend it to everyone. View detail
Reflects light well and contributes to safe driving.
I bought this for Repair because one day I was parking my Motorcycle on the parking lot and it was stripped by the Prank. I am very happy that I was able to attach it to a Fender Eliminator made by another company. The shape is cool too! View detail
Impact is greater than expected!
Needed for car inspection? I bought it because I thought I might need it for my car inspection.
Bought it for the look of the picture and the price!
The texture etc., is very good.
When installed, it has a strong presence.
View detail
Reflector kit
I bought it to go with my Active Fender Eliminator Kit! It looks really cool now that the License Plate has been reflashed! I recommend this product because of its low price! View detail
Japanese Vehicle Inspection Correspondence
I am riding XL1200C SPORTSTER 1200, and I had been struggling with battery up. I changed the stop lamp and stop-lamp to LED, just to ease my mind. I like it because it looks very modern, but I lost the reflector. At first, I had installed Universal Lens, but I was told that there was a problem with the vehicle inspection. So we installed this product. I chose the silver color because it is white. It blends in so well that you wouldn't even notice it if you didn't talk to me. View detail
Looks Refreshing!
Looks Parenthesis better than OEM Product! View detail
SMARTest shape in compliance with laws and regulations
We replaced the Rear Fender of our CB400SF with Active's Fender Eliminator Kit, but since the Reflector was sold separately, we chose this product.
https://www.webike.net/sd/24858765/
This is a combination with Kore.
Various companies offer lineups in various shapes, but we felt that this was the best in terms of design and adopted it.
Photo Quantity:Limit the minimum area on the Rule as shown in the 1pc. eye (instruction manual). [Color] Clear. Excellent.
The reflective patterning is also well designed and is inspection compliant.
It has a long hole to adjust the height of the reflector by about 5mm, which is called ReflectorSlide function. This allows the reflector to coexist with a frame (depending on the product).
The Number and Reflector surfaces are folded at about 45 degrees, and the angle at which the Reflector is generally perpendicular to the road surface is desirable, so it is best to fine-tune the angle to match the Fender Eliminator design.
The Fender Eliminator on my own CB400SF Active is 40-Degrees, so a 45-degree finish should be slightly inverted Slant, but in fact it is almost vertical, so no correction was made.
HondaDream stores, for example, have a strict policy of not allowing illegal Custom vehicles to enter their stores, so it is necessary to take these measures when sending them in for inspection. (I was told by a Dealer)
Some of the cheap ones may have the red color of reflector faded by ultraviolet rays, or the design of the reflective parts may be so bad that the car will not be inspected after all. However, it is safer not to add any parts to the class for vehicle inspection.
View detail
With Fender Eliminator Kit
I purchased this kit along with the Fender Eliminator Kit.
It is a Slim shape, so it is good for Refreshing.
Installation is nothing difficult as it is simply inserted after the License Plate.
View detail
Fits: KAWASAKI Z750FX, KAWASAKI Z1000 MkII, KAWASAKI Z750FX, KAWASAKI Z1000 MkII
very good
It is usually a good product and the price and texture are good enough! View detail
I think it's good
It is a good product with a beautiful finish.
If I had to say something, it would be nice to have a more vertical lineup to prevent mud splashes.
View detail
No complaints
When MAD's Fender Eliminator Kit was installed on a CB650R, this reflector was used.
I have no complaints about the cospa, texture, or design.
View detail
Required for Fender Eliminator vehicles.
To increase the rigidity, I used Cemedine's METAL LOCK to fix the License Plate Holder firmly and attached it to the Reflector Bracket. View detail
Reflector should be attached.
I had a Fender Eliminator on my Axis Treat and cut the bracket that mounts the OEMReflector under the Number, so I stuck this product on the rear bracket part of the Pillion Bar of the Wills WIN.
The size is just right and the quality seems to be durable, unlike the ones sold in the 100s.
The double-sided tape provided with the product is a very strong adhesive, so it is best to position it firmly before attaching.
View detail
MONKEY125 pica.
I was using 4 Posh round reflectors on the front and rear of my MONKEY125, when suddenly 1pc. of the rear fell off and was lost. View detail
Installation on DF200E OEMRear Carrier
DF200 DJEBEL, but with DF200E OEMRear Carrier.
The DF200E has a long flap on the Rear Fender, like a Camouflage Flap, so it does not have a reflector in the OEM position of the DF200 DJEBEL. Therefore, the reflector is attached to the Rear Carrier, and a bracket is attached to the rear end of the Rear Carrier for mounting the reflector.
I had been riding without a Carrier Reflector for a while, but every time I looked at it, I felt uncomfortable with the mounting bracket growing out of the Carrier. Surprisingly high." We found out that the product was not as good as we had expected, and we decided to buy this product.
It is a product, but probably the same Size as OEM.
I ordered this product thinking that there should not be many different sizes because it is a standardized product, but I found exactly what I was looking for.
The only concern I have is that the OEM may have a protrusion to prevent turning other than the screw. There is a long hole on the mounting bracket other than the screw hole. This may be an anti-turn feature.
Since this product is secured with only one M5Nut, I thought it might loosen due to vibration.
As a countermeasure, we applied double Nut. I drove about 300 km after installation, and there is no loosening as of now.
This should help improve visibility from behind.
I think items useful for safety.
View detail
Inexpensive and fully functional
Used when converting an off-road motorcycle to a Fender Eliminator.
I also had to repurchase the product because it was broken in a fall, but the inexpensive and simple installation method made it easy to fix.
It also functions perfectly, including the reflective condition.
DAYTONA products with a large lineup of such basic parts can be trusted.
View detail
Use with Bush Face's License Plate Holder.
I combined it with PolishFace's License Plate Holder. I use Cemedine's METAL Lock to fix the Holder and Bracket tightly. It has a good feeling of rigidity. View detail