Reviews
Required Parts for Change Accent
These are the Parts required for the installation of the Change Accent, but we would like them to be included with the Body.
Change Accent, installed on sr400Final edition. I was not particularly dissatisfied without Assist, but after installation, "Snap" and Shift is entered, and it feels good. Especially, when waiting for a traffic light and putting in Neutral, Stress is also reduced.
View detail
The only color available is Silver.
[How is it used?
I bought it to add Accent while replacing the Plus screw that started Rust stopping the exterior of a pre-2000 vehicle.
In the past, there used to be a wide variety of color variations available from various manufacturers, but now they are rarely seen and the choice of colors has become limited.
Was the one you received as per Image?
The design of this type of aluminum spacer is common. FUJI TUBO type. The simple design with no bumps and no dents and the universal nature of the product made it very easy to use and just like the Image.
Was the installation difficult?
There is nothing difficult about this product, as it is installed by biting it in place of a washer when using a cap bolt.
How was your experience with it?
In functional components, as the appearance and product name suggest. Washer/Color. since it is only Power up!" Ya Better fuel economy! There is no effect of etc.
Since it is made of aluminum material, each piece is light in weight and can also serve as a washer, making it a very convenient product that can be used in a wide range of applications.
The BoltSingle Body can be used as a one-point accent when installing the License Plate, which is not so easy with the BoltSingle Body.
There is no effect of weight reduction, reinforcement, etc. (strictly speaking, there is a slight increase due to the color) and it costs a lot of money, but I like this kind of product and I am very grateful for it.
It looks like a one generation old FUJI TSUBO Type design, so some people may think it looks old-fashioned, but if you install it in a slightly older vehicle, you will be able to see the new design. "Oh, there were people wearing colors like this in this era..." I personally think it looks strangely like a good fit.
[Included Parts:were they on?
None
4Quantity:Considering that the price per set is 2,938 yen, the unit price per unit is 734 yen, and there are no color variations, I would like to see the product sold at a lower price, but since the product is out of season, it is probably a good thing that it is still on the market.
[Was there anything that disappointed you?
As mentioned above, there is only one color variation, Silver.
I have no problem with it, since I decided to just paint it whatever color I wanted after purchasing it, but to tell the truth, I would like to have at least Red, Blue, and Black options.
Other items that would be helpful
Point and hang of installation
As mentioned above, it is like a fashion color used in place of a bolt washer, so it is a simple job to use the Barnacle Collar when attaching a cap bolt of the appropriate length to the bolt stop on the attachable part.
[Availability and clarity of the Instruction Manual
No Instruction Manual is available
It is a very easy-to-understand product, so I don't think that incorrect usage is likely to happen.
[Notes]
None in particular. Please note that there are no colors other than Silver available when ordering.
[ITEMS TO BUY TOGETHER
Cap boltTypeExclusive Collar, so please prepare a cap bolt of each material & length you want to install.
[Opinions and requests to Manufacturer
I am grateful that they are selling them in this day and age, but I would like to see them sell cheaper equipment if possible.
View detail
Universal and can be used in many ways
[How is it used?
The bar of the external Rear Sets was not long enough, so we put it on to extend the length.
I personally prefer longer ones because they are easier to load.
Was the one you received as per Image?
As per Image
Was the installation difficult?
It is easy to insert between Footpeg and Footpeg Plate.
How was your experience with it?
It serves its purpose because it is used as a simple color.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
It's just a color of Aluminum, so it could be a little cheaper. I thought it was a good idea.
but it is good to have a variety of Sizes to choose from.
View detail
Used to reduce rattling of Brake lever
[How is it used?
Brake lever was rattling badly and I bought it in hopes that it would get better.
The Touch feeling of the MASTER itself was not so good, but I suspected that maybe it was because the rattling was so bad that I could not press the Piston straight? I also suspected that it might be because I could not press the Piston straight.
To be honest, since it is a SmallEngine Displacement Volume for a foreign car, I thought that the rattling might be terrible combined with poor accuracy, but I tried it when I learned from an article on Webig that this Washer can reduce the rattling.
Was the one you received as per Image?
As you can see in the picture, it is just a Washer.
It is not a very expensive product, but the price of this thin Washer may be too expensive for some people...
Was the installation difficult?
Simply remove the Brake lever and insert it in between.
Washer is just on Lever, so it is a bit frustrating to have to Gap it back to MASTER.
How was your experience with it?
Actually, I first tried 0.3mm, but did not feel much change. 0.6mm with 2 layers of 0.3mm reduced rattling in a good way. However, I felt that the movement of Lever was a little reluctant or stuck, perhaps due to the two layers of 0.3mm, and I felt it was dangerous.:I settled on 1pc. Even with 0.5mm, there is some rattling, but it has been reduced to an acceptable level.
However, I did not see any large change in the touch feeling that I had expected, and I felt again that in such a case, I had no choice but to replace the entire MASTER.
[Included Parts:were they on?
Washer only.
[Was there anything that disappointed you?
nothing special
View detail
Spacer's Washer.
Clutch lever rattles less. Highly recommended! View detail
To M8 with M10 color
I wanted to use the Exclusive Aluminum Spacer for M10 Screw Collar from the same K-CONBrand with M8 Bolt.
These itchy parts are very helpful.
Surprisingly, there are no conversion parts like this.
View detail
Fits: Others Taper Handlebar(Φ28.6) vehicle, KAWASAKI Z900RS
I like that it doesn't rust.
I bought it because I couldn't wait for months to buy HURRICANE stuff.
I bought it because it is Stainless and I thought it would not rust.
I used it on a Conti2 model and had no problems.
View detail
Still a little expensive.
As you all say, a little expensive.
I'm in the mood to raise the price of Body.
It would be better to make this one cheaper.
It's a product of the year and whether you need it or not.
I know it can't be helped, but …
View detail
Gold parting, things are just fine.
When I installed it on the tank, the look was a combination of calmness and a sense of comfort that I had expected.
The colors are quite close to KITACO's shades.
I thought it was quite expensive and was not sure about it, but I bought it.
I was disappointed that the back side of the "Rucksack" was so smooth. I thought there was a Rucksack. So it feels heavy.
Installation is easy as all you have to do is replace it.
It is nice to know that the color does not easily fall off when the Bolt is removed as in NORMAL.
When the NORMAL collar is removed, a hole like a drain hole appears.
This color is also concealed, so I am OK with that, but I thought it was questionable whether the purpose of this hole could be continued.
The color of the Side cover is NORMAL, but I am confused about many things.
View detail
alignment
Rear Sets position, used to avoid interference.
Quantity:1 Set of 2pcs., good product at a reasonable price.
View detail
Lineup of other materials would be better.
I purchased this spacer to connect the shift arm to the GEARShiftClamp when installing an external footpeg kit on my NSR250R MC21. I really wanted a Brass spacer, but they didn't have any, so I went with an Aluminum spacer. View detail
alignment
Rear Sets are installed for alignment and fine adjustment.
Size type, Quantity:2pc. Set-in, the price is not that high, which is helpful.
View detail
alignment
The Rear Sets are replaced together with Bolt for alignment.
It would be nice to be able to choose Size, etc., but I wish the price was lower.
View detail
Frankly
I bought these because they interfere with the exhaust guard after replacing the bore AceRear Sets. The rear brake is very good. The quality was good as always. View detail
toolbox
I enjoy keeping them in stock.
We are gradually increasing the variety
View detail
toolbox
I enjoy keeping them in stock.
We are gradually increasing the variety of our products.
View detail
I'm glad I was able to use it.
I switched to NINJA1000sx, and when I tried to use STAND, I bought the color that fits without any research.
If you are looking for the best in the market, you will find that there is a lot to choose from.
I used it because it arrived immediately after ordering and the Size was right.
View detail
If you're going to install it securely, be prepared.
I bought this because I needed it to install ShiftAssist, and I was able to install it on my 2013 model without any modification.
InstallationInstruction Manual is not included in the package, so I installed it referring to the one I checked on Net.
View detail
Good product
I used it to adjust the Exhaust Band fixation.
As a Spacer, it is neither good nor bad.
The sale of Small portions is very helpful.
View detail
I used it to increase the height of the Handlebar.
Although this spacer is aluminum, there is a high-grade feeling because it is nickel plated. I was looking for a spacer with a good finish and shape because the mounting position is a noticeable point. View detail