Reviews
Fits: HONDA APE 50, HONDA XR100MOTARD, HONDA APE 100, HONDA XR50 MOTARD
Replace with OEM plastic
Replace with OEM plastic
Refreshing to look at, but not Impactful, and
I am going to try to paint it Black.
View detail
Fits: HONDA SportsCUBC110/C111, HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA SUPER CUB110
around this time an article was sent to me
The delivery was delayed during Corona, but I received an apology email from the person in charge and was grateful for the Large change.
As others have mentioned, the original Chain Cover Bolt is too short for installation.
6×10 Bolt and Washer are required.
View detail
Fits: HONDA SportsCUBC110/C111, HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA SUPER CUB110
Is it an individual difference? Definitely needs a separate screw
For weight reduction and dress-up.
Required Tools
10mmSocket
M6×10Screw (Pitch 1.0? site check required)
Some people seem to be able to use OEMBolt, but I couldn't. It broke.
This Parts is fixed with 2 Bolts (Driven and Drive side)
I initially tried to use Bolt and temporarily tightened the Driven side by hand and then hand-tightened the Drive side.
Then the screw on the Driven side blew out.
Upon checking, the Screw hole on the Driven side was slightly licked.
When the Bolt is aligned with the Parts, the OEMBolt is only long enough to have two Screw threads protruding, and the Screw threads seem to have lost shear stress.
I bought Bolt at Home center and used it on the Driven side.
The successful attachment method is Drive (OEM) →Driven (Homsen) The order is tentatively assembled and tightened in this order.
After several attempts, the Drive side also licked the Screw hole a bit, so I should have used the Homsen Bolt from the beginning.
As Chain Cover, it does not cover the Chain.
Perhaps my individual is deformed on the outside.
If it is divided into dress-up and lightweight, I think it is cosmetically pleasing.
View detail
Maybe I need a washer?
A heat-resistant SoftWasher is recommended to prevent wobbling. View detail
Fits: HONDA CB400SF, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR, HONDA CB400SF
Mounted on cb400sb NC42
The item arrived and there was a chip at the very edge.
I used it as it is because it is out of sight when installed.
I'm a little disappointed.
If the OEM footpeg is attached, the Hexagonal Wrench could not be installed without removing the footpeg, which was quite a challenge, but I was able to use a hexagonal wrench from a 100 yen shop that was just short enough for the job.
It would be easier to remove the footpeg or replace the bolt with one that can be rotated by Spanneretc.
It looks a little different, but...
View detail
Fits: HONDA SportsCUBC110/C111, HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA SUPER CUB110
cheap
CUB has a Chain Cover as Standard Equipment, but there are different tastes.
I'm running without the cover for ease of maintenance, but I want to cover the upper part like a normal motorcycle, so here it is.
It's carbon style, but the texture is appropriate for the price, but it does the job.
View detail
I'm satisfied with how it looks.
I installed this on a 2016 LE, installation is easy, takes about 5-10 minutes to complete the replacement.
There is a large difference in the appearance from the time it was applied, the time performance is excellent, and the shining power of the plating has changed the impression.:The difference in texture from the black plastic cover and the power of the reflection from the shine of the plastic is tremendous.
But Material:I haven't weighed it, but the SteelPlating cover I installed this time is made of Material:It weighs about 10 times as much as Plastic, and I felt that things were different.
Since this is not a MotoGP machine where the weight under the spring is important, I installed it just for looks. I think the texture of each and every part of the W800 is more suitable for the atmosphere, so it would be a shame not to add the SteelChain Cover. It was a shame not to add the SteelChain Cover.
Material:The texture and workmanship is beautiful, and the brilliance of the plastic was a perfect match. By the way, ESTRELLA's cover was made like hand-finished.
Please note that the installation screw for the Plating cover is not included in the package.:I reused the black screws from the Plastic era.
Is Mr. Han Kawasaki also a CostCut in the current trend?
View detail
Fits: KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z1 (900SUPER4)
I can't help it, sir.
Bolt to hold the Chain Cover.
It has a special shape.
When I used All Screw's Bolt instead of this Bolt, the Chain Cover was Gapped.
It's a special Bolt, so it can't be helped, but the price is high.
View detail
Fits: HONDA REBEL250, HONDA Rebel300
Good news for Lowdowners.
The OEM Cover looks kind of cheap and I wonder if there is something else?
I found this one when I was looking for a lot of things.
But I have a DAYTONA lowdown suspension.
I wonder if this part can be attached safely.
Will it interfere? I've been wondering about that for a while.
If it's about 10,000, it's okay if it's not.
In conclusion, I can install it without any problem at all.
It's done.
If you're struggling for any of the above reasons, please don't worry about your purchase.
View detail
Fits: YAMAHA SR400, YAMAHA SR500, YAMAHA SR400, YAMAHA SR500, YAMAHA SR400, YAMAHA SR500
Required when rear suspension is changed.
I installed this product to replace the rear suspension with Other Brand Product.
I was looking for a design that was as NORMAL as possible, and this product was it.
InstallationInstruction ManualThe manual is well written and anyone can install it.
View detail
Boltetc. for installation is missing.
The product itself can be installed with a little modification, but
Bolt is more than the listed numberQuantity:It had 2pc more in it and Nut didn't even have 1pc. in it.
I probably put Bolt and Nut in the wrong place.
I have purchased other products from this Manufacturer, but they are not as accurate.
The price of the gold is the same as other manufacturers, and I think it is better to buy other manufacturers.
View detail
Fits: KAWASAKI ZrX1200ZrX1200 DAEG, KAWASAKI ZRX1200R
High quality.
I don't know about the durability of this product, but I think the quality is very good. View detail
Fits: TRIUMPH Bonneville T120 2016, TRIUMPH Street Twin 900 2016, TRIUMPH Bonneville T120 2016, TRIUMPH Street Twin 900 2016
Fashion
It's just a few custom parts, but
I'm pretty happy with the atmosphere of the Motorcycle, and I'm very happy with the Classic.
It was easy to install and good.
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
I couldn't pimp it
I bought it to use on my 1979 MONKEY6v
I was going to install it on the OEM Arm, but I can't do it without expanding the hole
It was not possible to move the hole behind the body, so the hole in the front side of the body was widened to the front side
Therefore, the whole thing gaps backwards
I was able to install it, but the position of the ScrewCover on the Arm feels a little bit gapped to the back
OEMCover cracked or no OEMCover for those who don't have it, Recommendation
Cost-wise, I'm happy with it
I would have given it 4 stars if it was a little more carefully crafted
View detail
Fits: HONDA SportsCUBC110/C111, HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA SUPER CUB110
It became SMART
CUB's Chain case really "CUB" but
For protection of Chain?
As you can relax, as you can tell by sound ??
I rarely ride on rainy days and the road that runs is almost a paved road and it is not much meaning and it is light material : Plastic ...
Look at SMART (Self-satisfaction)
"Install Bolt uses the removed item" There is, but the thickness of the iron plate and the resin is different!
There will also be individual differences, but it only takes 1-2 mountains
People who buy Bolt are also safe
View detail
Parenthesis is nice!
I ordered with FRP Inner fender for VTR-F. However, the arrival was one month behind due to some reason. Inevitably FRP Inner fender was drilling and attaching to OEM's Chain guard. Finally I ordered FRPChain guard reached, Webike's delivery date has been destroyed Brown 苦 Brown was very troubled.
I managed to attach it with Inner fender, but Matching has no problem but I think that the feeling I saw is pretty bad. If you say that it is worrisome that there is a gap in the place where you fit it a bit, I am satisfied.
It takes a while for painting - - -. This time I made a deduction point in the part not meeting the delivery date.
View detail
Upper chain guard installation
OEM Plus Chicky looks bad Select Carbon.
Installation requires hole positions and mounting boss processing. In addition, Carbon made it thinner. We need to adjust the thickness with Washer etc.. The appearance looks luxurious. (^ ^ ♪
View detail
Since the Chain case made from a Plastic of the ready-made article had broken, it exchanged for this. Although the price is somewhat higher, the texture of a Carbon has a high grade feeling very well, and its structure of details is also beautiful.
Since the Chain case made from a Plastic of the ready-made article had broken, it exchanged for this.
Although the
price is somewhat higher, the texture of a Carbon has a high grade feeling very well, and its structure of details is also beautiful.
Although a little attachment is trouble, it is satisfactory.
It is thought that the appearance after attachment is also reasonable and became a Fashion.
View detail
Although nothing influences the engine performance, since a Parenthesis is good, it changes just.
Although nothing influences the engine performance, since a Parenthesis is good, it changes just. View detail
Fits: HONDA APE 50, HONDA XR100MOTARD, HONDA APE 100, HONDA XR50 MOTARD
Possibly a color did not suit AC18 just for a moment. It is whether to take pains just for a moment for wearing to stop a hidden nut. . .
Possibly a color did not suit AC18 just for a moment.
It is whether to take pains just for a moment for wearing to stop a hidden nut.
.
.
View detail