Reviews
Needs a little processing.
Mounting on zx4r
When we first aligned it, it was not accurate at all.
The warp is so shallow that when I pressed the tip of the Center, both ends floated quite a bit, the largest 8mm floated. It was too shallow to be held by double-sided tape. Finally, I heated the shallow part with a dryer and bent it. Fortunately, I was able to fix the problem by using cheap Carbon, which softened up considerably.
And the depth? I'm not sure if it's not deep enough or if it's installed in the wrong position, but I can see the Green.
View detail
Nut is not well fixed.
Purchased to remove the flap valve and make it full power.
It took 7 months to deliver the product.
Replacement from Straight machined OEMDuct, weight reduced from OEM approx. 350g to approx. 285g, which is like an error.
With a weight difference of this magnitude, I would like to see the product sold at a lower price in resin instead of Carbon.
I bought an OEMCap (92066-0717) to plug the hole in Solenoid, I wanted it to be plugged from the beginning because I don't think people who replace such parts would leave Solenoid.
The Gasket with the Frame is made of 100-yen Gap Sponge.
Installation is quite tricky. Both Duct and Frame have BALI at the Center, so they are like Seesaw and do not go deep enough.
When the bolt is forcibly attached while pressing down, the nut on the duct side rotates and cannot be tightened or loosened....
The OEM has a star-shaped nut embedded in the outer diameter that does not rotate, but this one has only a lightly crimped round type nut, so it rotates all the time.
In the end, I managed to install the FrameCenter by shaving the contact surface of the FrameCenter. I don't plan to remove it, but I'm not sure if it will come off since I put a screw lock on it.
The intake changed to Large width, so I adjusted the ECU before starting, and the effect was excellent.
The Torque is clearly increased from the start, and city driving is easier.
Motorcycle is a monster to begin with, but the Peak power has become even greater, and it cannot be handled by ordinary people.
View detail
Fits: HONDA MSX125, HONDA glom, HONDA glom, HONDA glom
Thick.
I'll have to replace the slobo as well to see the effect. View detail
Fits: HONDA MSX125, HONDA glom, HONDA glom, HONDA glom
Power up, this is not the only way to experience it.
[How is it used?
Used only in Circuit.
Was the one you received as per Image?
As per Image
Was the installation difficult?
Somewhat troublesome because the Air Intake hole in the Air cleanerBox needs to be widened with a Cutter. Be careful not to widen it too much.
How was your experience with it?
I saw a review on YouTube that said the power was increased, so I installed it, but I couldn't feel the effect.
Perhaps it is not that the product is bad, but rather that it is only effective when an exhaust system with good exhaust efficiency is properly installed and fuel conditioning is performed.
[Included Parts:were they on?
It contained a brochure of Mukawa's products.
[Was there anything that disappointed you?
Not being able to experience Power up.
I can't say for sure because I didn't measure it on the chassidai…
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Mukawa's Power Filter, Sub computer, and Racing Exhaust System are available in Quantities:Let's install it with Set!
View detail
Fits: KAWASAKI ZX-25R, KAWASAKI ZX-25R
Design is good, but texture is not so good
Air IntakeDuct and Quantity:This is a product that is intended for Set use.
Inevitably, this will be used.
The thickness is very thin, the same as the Punching board at Home center.
The Manufacturer logo is also a bit cluttered when viewed from behind, and I think the cost performance is a bit poor.
Also, the double-sided tape is used for the mounting method, but I wish they had devised a better method for that as well.
Air IntakeDuct is responsible for the performance.
View detail
Fits: KAWASAKI ZX-25R, KAWASAKI ZX-25R
Normal.
Trickster's Air ductGuard is not much different from NORMAL when installed.
It is not noticeable because it is in the Duct section. But I am self-satisfied.
View detail
A little frustrated
I was convinced that it would take longer to deliver because of the made-to-order nature of the product, but the + 1 week response was late
After delivery, I checked the product and found that the bottom part of the product had become cloudy and white
View detail
Fits: BMW RnineT, BMW RnineT, BMW RnineT Pure, BMW RnineT Racer, BMW RnineT Scrambler, BMW RnineT Urban G/S, BMW RnineT /5
Screw interferes
Screw for fixing sticks to the outer edge of the intake entrance, so the exterior interferes and it feels like it can not be installed as the original.
I feel that it looks bad.
View detail
It purchased by appearance serious consideration.It is better to carry out paint application as it has written on the description, although form is good.The surface is fairly coarse if it remains as it is. It is although attached without pain
It purchased by appearance serious consideration.It is better to carry out paint application as it has written on the description, although
form is good.The surface is fairly coarse if it remains as it is.
It is although attached without paint application for the time being.. Although it fixed with double-stick tape, the Tapping screw also attaches
attachment.Since appearance is spoiled as attaching a Tapping screw also by
, it is fixing only with double-stick tape.
View detail
It purchased by appearance thoroughly. attachment is really troublesome. (A SIDE & Front cowl is removed) weight became half. Considering the field of Cost & attachment, a degree of satisfaction is common.
It purchased by appearance thoroughly.
attachment is really troublesome.
(A SIDE & Front cowl is removed)
weight became half.
Considering the field of
Cost & attachment, a degree of satisfaction is common.
View detail