Reviews
viscosity
When I remove the Cover during the next touring after applying the adhesive, the pad at the bottom is fluttering. Already no adhesion.
It was put on by a Shop Service person. I wouldn't write this kind of comment, but it's a pity that PRO put it on.
I'm wondering if I should buy the same item.
View detail
Fits: HONDA , HONDA CB500X, HONDA CBR500R, HONDA Rebel1100 DCT, HONDA CRF250RALLY S, HONDA CRF250RALLY, HONDA CBR650R, HONDA CBR400R, HONDA CB650R, HONDA CB1300SUPER FOUR SP, HONDA CB1300SUPER FOUR, HONDA CB1300SUPER BOLD'OR SP, HONDA CB1300SUPER BOLD'OR, HONDA CB1000R, HONDA 400X, HONDA Rebel1100 T, HONDA Rebel1100, HONDA CBR650R, HONDA CB650R
Nice looking sticker on the tank!!
For my 2023 Honda Rebel 1100 - very simple to apply, just makes sure alcohol wipe the surface first and then line up the stick with the gas tank. You might experience some unaligned screws holes on the sticker, in that case use a heat gun gently on it then use hand move the stick to the proper positions. Overall - nice looking products but for almost $20 I think is little over price, and not sure how long it last. View detail
Air bubbles will be noticeable.
My first impression was that it was smaller than I had expected.
It is a little small for a Large Motorcycle, giving the impression of unbalance.
The advantage is that it is transparent and allows the best of the paint to be used, but on the other hand, air bubbles can be noticeable, so it must be properly warmed up and applied neatly.
If the angle of the tank is sharp, the edges will peel off, so you need to warm it up thoroughly and degrease it before applying it. I replaced the tank pad with another one because I was concerned about air bubbles and the shape of the smallest tank.
View detail
I don't see the need for it on public roads.
I have not ridden on it yet since it was installed.
The reason for this is that once installed, OEMSeat is no longer available!
View detail
The look and feel requires Zero preparedness.
The product is extremely cheap, and I thought it was a SiliconCoaster that you can buy at a 100-yen store. It was so solid that I thought it was a cross section of a fish cake, and there was no texturing process, etc.
Undoubtedly, it will make the installed vehicle look cheap.
I can honestly say that the texture and build quality are definitely not worth the price of the product.
If judged by product production Cost, it is clear from the appearance that the R&G company's product is definitely much more costly, and the dress-up satisfaction is higher.
As for the feeling of use, it shows an effect (high gripping force) that is commensurate with its material. In my case, I have a habit of sliding the product on the contact surface when I move my posture, so I prefer a slightly weaker grip like R&G's. However, R&G's support for GSX-8S is more effective (high grip strength) than R&G's for Tank side. I prefer the slightly weaker grip support force of R&G products, but the R&G product for GSX-8S has a pad on the tank side but no pad on the frame cover side (lower side), which is unfortunate.
Therefore, R&G tank grips are only used in very rare situations, such as when a turnaround of winding is necessary, when a high-speed corner is turned in, and when turning, and therefore, the support as a tank grip is not obtained. It is a mere decoration. (I am 176cm tall and have an 85cm inseam.) ) We would like to inform you that we had no choice but to purchase this product for this reason.
In addition to the above, care must be taken during installation. The included degreaser is extremely aggressive to the frame cover and will definitely discolor the resin parts to a whiteish color. However, for those who focus on keeping the body clean and well-maintained, it is likely to receive a very Large mental Damage.
For this reason, we can say that if you are nervous or are also considering a Case to remove SiliconPad, you should be careful about using the supplied degreaser.
View detail
Fits: SUZUKI Universal, SUZUKI Universal
It's kind of thin and cheap-looking.
It is only a Carbon Style Seal.
It is thin without thickness and looks cheap.
Well, the price is the price.
Tank cap is dirty and just right for a blindfold!
View detail
Weak adhesion
The one on the Tank is Large sturdy, but the one on the resin part is too weak adhesion!
It came right off ….
The color is more Color than Black.:I think it would be better to say Gray
View detail
[Color] Clear does not recommendation
[How is it used?
I bought this so that I could use a little less force on the Knee grip, but when I applied it myself, it had too many air bubbles, so I bought it a second time. [Color] Select Clear
Was the one you received as per Image?
I knew the Grip force and the Hold force when Cornering, so the performance is as per Image.
Was the installation difficult?
I applied it once by myself and it left air bubbles and came off, so I had PRO reapply it when I took the car to Coating.
However, even so, it seems that it was impossible to completely eliminate the air bubbles or wrinkles and apply it perfectly, and although there is no sign of it peeling off so far, it honestly looks bad.
It would be extremely difficult to apply it neatly to the curved surface of Tank without processing.
How was your experience with it?
So far there is no sign of it coming off.
Lines like Wrinkle also became unobtrusive Levels once you step away from them.
The Grip force is perfect, but whether it is good or bad depends on the person, but my thighs do not hit the Knee Grip Pad in Straight and normal Cornering without Hang-Off, because my thighs do not usually hit the position where it is attached.
When Hang Off, it hits the sticky thighs, but it can only be used there.
[Included Parts:were they on?
Comes with degreaser and Manufacturer logoSeal.
[Was there anything that disappointed you?
The first time I did it as a DIY project and thought it was my lack of skill because I failed, but I asked the store to do it for me and it was only slightly better and the manager "The curved surface of the Tank is too tight and this is the limit. I don't think it will ever come off." And that was just the minimum.
I thought, "What is the purpose of Exclusive Design for a car model if it cannot be applied neatly because the curved surface is too tight?
The solution was in someone else's Review, [Color] If it is not clear, but with color, the wrinkle will not be noticeable and will look beautiful.
Or you could cut and make it yourself.
As long as the wrinkle doesn't float and start to peel again, I will continue to use it, but if I have the opportunity to replace it, I will use the Black color next time.
View detail
I can't get it to stick.
Even though I applied it as described, it still left a white residue. In addition, the bottom part does not fit the curvature well. In the end, I peeled it off and threw it away.
Ask Shop to install this product.
View detail
not quite
No way, there is a round hole in it.
I can't believe they framed a Seal like Logo design's Cushion...
Low rating because the design is not good.
Grip is Normal I think it is. I think it's better than when I don't have it on.
Grip.
View detail
Fits: KAWASAKI ZZR1400 ABS, KAWASAKI ZZR1400, KAWASAKI ZX9 R, KAWASAKI ZX-6 R, KAWASAKI ZX-10 R, KAWASAKI Z1000, KAWASAKI VERSYS, KAWASAKI ER6 n, KAWASAKI ER6 f, KAWASAKI 1400 GTR, KAWASAKI Z750 07-08, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200, KAWASAKI ZZR1200
Mount Screw
I was looking for a black Titanium, but I couldn't find a good one, so I chose this one. I tightened the bolt lightly by hand until it stopped, but when I looked closely, I found that the screw at the tip of the bolt had been crushed. I thought there was a problem with the Bolt, because the other Bolts I had went in without any problem. It is a waste of money, but I am afraid to use a tool to tighten it, so I will look for another one. View detail
Not what I was expecting lol.
I bought the Logo from RyTEC because I thought it was stylish, but I didn't think PadBody would be. [Color] I didn't think it was Clear.
If you put it on a black tank, you can't even see the logo.
If you accidentally touch the back side, fingerprints will be left behind and you won't be able to remove them.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
Tank capPin cannot be removed by Punch.
First of all, I could not remove the OEM Pin.
The pin cannot be pulled out even with a 3? or 2? punch. The Instruction Manual says that it can be easily pulled out, but without a special tool or something, it will not come out.
I'll leave it alone for a while.
I wish ARCHI would give you a video of the installation too!
View detail
Is this United StatesQuality?
Purchased this for my Z125Pro. The one I received was defective in that the adhesive was taken away by the backing paper. I immediately took a picture and contacted them and they handled it as an initial defect and sent me a replacement within a few days (although it also took a few days from the time I contacted them until they started to respond…). The replacement looked fine, as did the adhesive. However, when I finally tried to install it, I found that the Quantity:Pair (for Left and Right) The shape was different in I thought it was another defective product, so I compared it with the first one I received, which I had not yet sent, and found that it seemed to be Quantity:Pair (for Left and Right) The unevenness seems to be a spec. I had no choice but to cut and shape it myself and installed it. It was a little problematic, but it seems to help the Knee Grip. I think the price of 12,100 yen is still expensive. View detail
Fits: DUCATI SUPERBIKE Panigale V4 S, DUCATI SUPERBIKE Panigale V4 R, DUCATI SUPERBIKE Panigale V4, DUCATI SUPERBIKE 955 Panigale V2, DUCATI STREETFIGHTER V4, DUCATI STREETFIGHTER V4 S
Different quality from JAPAN
It looks cool at a quick glance, but the surface is full of bubbles (bubbles or Garbage?) and the quality is quite poor. View detail
? I was so scared.
I degreased the sticking surface cleanly and stuck it on, but it peeled off beautifully.
The rest will peel off no matter how many times it is pasted.
I'm sorry
View detail
Fits: SUZUKI GSX1300R HAYABUSA
Tank Shop
Crystal in Bolt is in the way and hard to tighten. View detail
Saitaniya Tank Cover/Full Covered/Tank End Original Shape
MV AGUSTA F4RC RepartoCorse-MOTUL also
I've already purchased the same manufacturer, so it's not a problem;
SaitaniyaTank Pad for 2021 MODELKawasaki-Ninja ZX-10RR
I asked the store to install it for me.
Because it's a full cover? It cracked on the second day of purchase.
Especially every time the bite part rides and banks.
It's cracking and splintering. The bubbles are terrible.
[Angle] The white part of the picture is the crack that was repaired. The other side is also amazing!
I'm riding a restored Aron Alpha.
But it looks good, so let's call it good.
View detail
disappointing
The quality is worse than I thought.
I feel like it will be ruined in about 6 months.
It is not recommended.
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA monkey, HONDA monkey
Rough finish
I bought this because I was sick of the Chinese Tank.
The welds on the back of the Tank and the overall finish are too messy.Cap does not come with the Cook.
View detail