Reviews
It's hard to understand the instructions
It took me a while to get it to fit, but the instruction manual was confusing and cumbersome
I stopped halfway through I'm still wondering if it's a good idea to cut Fender
I'd return it if I could
View detail
Typical cheap and bad
To put it bluntly, it's a lazy product with a near defective design, so it's made by HURRICANE Don't buy the Fender Eliminator Kit for the SC77 from
Because it only comes with a Bracket for License installation and there is no Cover There will be a gap between the accessory case and inner fender Therefore, water or other contaminants may enter the Accessory Case or Inner fender under the Tandem seat Garbage, sand, Small stones etc., quite a lot of them get in
Moreover, because the Small stone etc. which Tire wound up hits the Accessory Case directly And the Accessory Case has been torn to pieces
In the product information, Base plate is Material:It is called Aluminum, but the license light Plate is made of steel and poorly painted
It's already pretty rusty despite being in use for less than six months
When I contacted the Manufacturer Our spec. is based on consideration of cost and fitting methods
So, I thought that the water etc. will be in the Spec. so I should be patient
For Accessory Case measures, you need to process aluminum plates etc. to make the Cover's It's better to buy a competitor's product from the beginning because you will have to make and repaint your own
View detail
Fits: MV AGUSTA Stradale 800, MV AGUSTA RIVALE800, MV AGUSTA RIVALE800, MV AGUSTA RIVALE800, MV AGUSTA RIVALE800, MV AGUSTA DRAGSTER 800, MV AGUSTA Stradale 800, MV AGUSTA Stradale 800, MV AGUSTA Turismo Veloce 800, MV AGUSTA Turismo Veloce 800, MV AGUSTA Turismo Veloce 800
Not a Fender Eliminator
MVAGUSTA Rivale, Strada-les, F4-BRUTALE and Turismo The license plate common to all Veloce brothers fits in the same place in Compact It is not for relocating to the tail lamp or tail cowl part because they are Parts The product description and images are so simple that they could be mistaken for a Fender Eliminator I will be happy to do so View detail
Tiny
Double-sided Tape and Tie Wrap instead of Screw Fixing
Moreover, the attached tape peels off easily because of the pearskin fabric
At 1000cc, this is cheap and it's RiskLarge!
The shape isn't great either
View detail
The delivery time is about a month
It's about $10,000 cheaper to buy on Yahoo! View detail
Fits: YAMAHA MT-03, YAMAHA MT-25, YAMAHA YZF-R25, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3
I ordered but it didn't ship so I cancelled it and didn't return the Gold
The Manufacturer here only receives the Gold and does not ship it
So I did Cancelation
But no gold has returned
It's the worst
View detail
Fits: KAWASAKI Z900RS Cafe, KAWASAKI Z900RS, KAWASAKI Z900RS SE
Daddy's fender
The workmanship of this extended fender is okay. The installation method is actually glued with double-sided tape. I reported the mentality of giving it a try. On the first day on the high speed, I dropped it and lost it. This brain-dead design! Just want to complain! If you really want to buy it, you still have to nail it with a screw, but neither the extended fender nor the original fender has screw holes, so destructive drilling is required. Is there a word limit for comments? I'm going! This extended fender workmanship is OK, the installation method turned out to be double-sided adhesive, and reported the mentality of trying it out. On the first day, the high-speed will not lose sight of the public, and this brain-destructive design! Just want to vomit! If you really want to buy, you still have to nail it, but the extension fender and the original fender have no crepe holes, you have to do destructive punching. Comments also have word limit? I am going !(translated by Google Translator) View detail
You had better stop it.
Even if we wait 3 months, the product will not arrive, we will make an inquiry from here, it will be kept waiting for 2 more weeks, waited for another 10 days and arrived again 5, arrived finally, the parts are too bad. Firstly, the attachment hole that would have been opened with Drill is almost broken. I was told that once due to defective goods the delivery date has been extended, but it is very disappointing that this is the result of redoing. Usually I do not mind about this, but the matter on the delivery date, the delay in contacting the delay, whichever is the lowest. Those thinking of Fender Eliminator of sc59, do not adventure, Domestic Manufacturer is cheaper and earlier, I think Quality is high. It was really disappointing.. It became a high study fee. View detail
![Rear Fender [Sportsline Rear Hugger]](https://img.webike-cdn.net/catalogue/images/47174/0546_TS.jpg)
Fits: BMW C 650 Sport, BMW C 650 Sport, BMW C 600 Sport
Inner fender falls short
I'm debating if this fender is worth $200 when it barely covers up just a few inches above the swing arm. What happened to inner fenders that actully cover the tire?? View detail
will not fit stock Honda Zoomer width rim and tire
well made item but is far to narrow to fit a Honda Zoomer running a stock rim and street tire i will have to modify to make this fender work with my bike i am not impressed as all other Rin Parts i have on the bike work/ fit perfectly View detail
Fixing Screw is few and Gap is Large.
Because there are only three Fixing Screws, Gap occurs and the clearance is Large.
Disappointed. Cover is unnecessary because it is necessary, but it seems to be fixed only with Tape.
View detail
Fits: KAWASAKI Z1000, KAWASAKI Ninja1000, KAWASAKI Ninja1000 SX
Not good. Anxious products.
I thought that the footwear would be muddy with Fender while leaving the OEM but purchased by judging that it is cheaper to install this item rather than to replace Fender entirely, but because the installation was quite uneasy because it was only an adhesive, I did not use it though it did..
Other Reviewetc. I think that you can see that it gradually comes off and does not last long as it is.
In terms of long term, I think that it will be cheaper to change the type that turns around for every Fender.
I bought this whole Fender after buying it.
This is 9,000 yen. If you change the whole, 25,000 yen.
View detail
Fits: KAWASAKI Versys KLE 1000
It is 2017 model of Versys 1000 which can not be installed.
It corresponds to ALL MODEL, but it does not include. It is a structure to install using Reflector's M6 Nut, but it was impossible to install because the shape width of the product is different from the Fender shape on the car body side.
To the enclosed instruction manual was only one sentence that you put videos of how to install on YouTube. For Versys 1000 it may be possible to install it if it is MODEL before 2014.
View detail
It's the worst.
CRM250Rr (MD24-140XXXX) I was trying to attach it to the level, but it was Level which makes me think about conformity, there was not anything of dimensions.
For those that are not compatible, you will find that it is necessary to process a lot.
Despite being stated as conforming, you have to cut down SIDE considerably.
When thinking that it entered, the width of the R part that comes to the bottom of Seat is also too large, so you have to force and tighten with Bolt and pulling it down, the Tail part also turns upwards due to its bowing and forcibly tightening with Bolt.
Of course, unchecked state that it jumps upwards with a shabby!.
The gap between the Fender part and the Body part that comes to the Engine side can also be quite Gabagaba. (Please take a look at the photos as they can not explain well in words)
Since it is a Saturdays and Sundays event, we have not heard from Support yet, but it is a product of Level that can not be convinced if we can not return it honestly.
Screw Not enough to open a hole Processing at the Level Level can not be fitted properly = I think that it is a defective item from the beginning.
Evaluation of other people seems good, but I definitely will not recommend it.
View detail
Do you want to make it, do not you want to sell it?
After placing an order, I waited for four months but the arrival schedule continued to grow.
Accurately from the beginning leave the delivery date unknown.
It is a selling fraud to sell.
Even as Webike, please do not post such items.
I'm sorry.
View detail
Fits: KAWASAKI Zephyr 750, KAWASAKI Zephyr 750
The product is nice..
Open it. Bolt kind comes with RoseRose, there is no Instruction Manual, it is the worst. A shop!
It is the first time. There are such sloppy shops!
View detail
Fits: KAWASAKI Zephyr 750, KAWASAKI Zephyr 750
The product is nice..
There is no manual, Bolt kind does not enter the bag RoseRose, too complicated and there is no instruction manual, you will not talk. So much, there is no complicated Instruction Manual, Shop is the first time. View detail
LED not lit
I installed it and License Plate Light does not light, I know that I mail it to webike but leave it alone.
To inquire about Manufacturer
There is no contact now.
I should have bought another Manufacturer.
View detail
Fits: YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA YZF-R3, YAMAHA YZF-R3, YAMAHA YZF-R25
Cheap and bad
Speaking of Inner fender, Carbon thought it was a pair, but it was Painted's Inner fender, so it was an unusual kind of purchase. The first impression I received was that the Material, the paint was cheapish. While feeling a bit uneasy, try installing ... ... in anxious way!
First of all, the gap between Tire and Fender is too wide! Because we attached other Manufacturer's Inner fender to Motorcycle other than R25, I was amazed at the inferior gap of the Inner fender for R25 that arrived! Close to the inexplicable thing saying why you need such a gap, why are you doing the same up and down? ... And, more than anything, Parenthesis of the moment you saw with Back shot! It is distorted and distorted! Although it is a Tire house, even though it is a Tire house, Not being shaped along! It's not good to cover the Tire!
Considering the price I thought it was a predictable situation and it became high shopping! Inner
View detail
ZZr1100 Carbon Font Fender
Try purchasing, first thought I was thin. Although reinforced with FRP, it is doubtful how far it can withstand wind pressure. Installation is also OEM one point 3 point stop against 2 points stopped and can not fix and move with the graffiti. I thought that I could not bear to practical use, so I decided not to use it.
View detail