Reviews
I'm not that happy for the price.
It's a little bit longer. There's a dress effect where the body looks a little bigger, but there's no significant change in appearance. I'm not that happy for the price. View detail
It arrived a month early... but maybe I had high expectations...
Of all the Magical Racing products, this was the most expensive one I bought and had the highest expectations...
I really liked the room side tape inside and lots of cushioning products.
However, when assembling, the bolt holes did not line up, so I had to do some machining.
I'm so scared of taking the under cowl off again.
It may not fit as well as the original cowl, but
A few of the bolt holes were misaligned, so there was a situation where the carbon broke into small pieces during processing, but it was still too far to replace it, so I just used it.
It's not as good as a homemade cowl, but it's a product that requires some processing ㅠㅠ ------------------------------------- --------------------- Of all the Magical Racing products, it was the most expensive and had the highest expectations... I really liked the room side tape inside and Lots of cushioning products. However, when assembling, the bolt holes did not line up, so I had to do some machining. I'm so scared of taking the under cowl off again. It may not fit as well as the original cowl, but A few of the bolt holes were misaligned, so there was a situation where the carbon broke into small pieces during processing, but it was still too far to replace it, so I just used it. It's not as good as a homemade cowl, but it's a product that requires some processing. Powered by Google Translator
View detail
Cowl mounting holes do not fit
Paint quality is good. It makes it look like a new car! I had to force it on with Tie Wrap or re-drill the holes … I think it may have been an individual mistake, but … I drilled the holes with a Drill and installed it. If you can install it, you will be supremely satisfied. View detail
I wonder if it's not a pimping?
It was not easy, as I had to shave a little and bend it with a heat gun. View detail
fitment issues
I was excited to recieve this poduct. There are a few fitment issues with these plastics for my af27 dio. The front piece the 4 bolts on the back side only two line up the other two are so far off would need to enlarge holes to make it work. The top headlight piece does not fit well pops out on the one side and on the middle. The rear pieces seems to fit alittle better but not the best. View detail
Fits: SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI GSX-S1000F, SUZUKI GSX-S1000
Processing is assumed to be Large.
The Instruction Manual states that some modifications may be required, but basically, Dry Carbon, an Other Brand Product, can be installed without modifications in most cases. As usual, this product also requires modification. The remaining 20% will be modified during the installation process.:Pair (for Left and Right) The gap between the two is different, so if you are concerned about the gap, you should refrain from using this product. I had high expectations for this brand because it has been gaining momentum recently, but I have a problem with the outside of Dry Carbon products, including some AEC products. View detail
Design is fine, but ...
We like the design and use AERO Type.
My MONKEY125 is overdriven and travels about 20,000 km per year.
The car is 99% on road, so it is not running in a place with severe vibration, nor is it experiencing abnormal body vibration due to breakdowns, etc.
In fact, this is the third one I have purchased, because after 10,000 km or so, the area around the mounting point is cracking.
1pc. eye near the mounting Quant.:Pair (for Left and Right) The second time, the Right Side crack was quite large when viewed from the front and was repaired once, but as a result, the cracks expanded and became larger and larger.
Therefore, this time RType was purchased as Repair Parts because it is cheaper, and the original AEROScreen was transplanted.
I would like to see a little more durability, because I can't easily cheat on my MONKEY125 with another Bikini cowl, as it has become the identity of my MONKEY125.
I think it would be good for owners who are not over-driven like me, so if you like the design, you may purchase it.
View detail
Requires ingenuity in installation
As for the installation, it was difficult to install the LowerBracket to the vehicle body.
Also, I have a BEET Taper Handlebar, and I changed the Bracket of the BrakeReserver tank to the Exclusive Bracket that came with it, but it interferes with the Cowl quite a bit without modification.
Light can only be adjusted by removing the Cowl.
View detail
Processing required
Installation is by a single Screw in front of the OEM Under Cowl and double-sided tape on the SIDE.
ExactlyDouble-sided tape does not feel like it sticks, so I drilled a hole and used Tie Wrap to hold it in place.
It was like we had to do something creative to stop it.
View detail
V-max 1700 under cowl(Twill Carbon)
I ordered it on June 25th... I received a reply that the expected delivery date was October, but I received it approximately 5 months later. Unfortunately, the customs clearance process was complicated, resulting in additional costs and additional freight charges. View detail
Fits: YAMAHA SR500, KAWASAKI ZEPHYR750 RS, HONDA CB400SF, HONDA CB400SF, HONDA CB400SF, YAMAHA SR400, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR400, KAWASAKI ZEPHYR400χ
It makes you look pretty.
I think the price is reasonable and it is a good product for casual makeover. I think it looks cute.
Installation was a little difficult in positioning.
The drawback is that the LightBody of the car body gets small scratches at the installation pin if the positioning takes too much time and has to be redone.
Rather than putting it on and taking it off, it might be better to leave it on after putting it on.
View detail
It's not quite Exactly.
It seems to be handmade, so it's not exactly Exactly.
I think Cool.
I was worried about the double-sided tape alone, so I dotted Coking on an inconspicuous spot on the edge and installed it.
I don't feel out of place when I go Touring.
View detail
Recommendation for those who can paint & process
I bought this for APE 50.
Since Saiya's products are made-to-order, you have to wait almost a month for them to arrive.
*Good point
Appearance Installation instructions included
*Notes
GlassWool is ParaPara peeling Dents and scratches
Helmet holder attached to APEFrame interferes with Cowl.
Scratches and dents are a prerequisite for painting.
If you are OK with these, consider purchasing them.
View detail
Wind protection effect is questionable.
[How is it used?
The wind at high speeds is hard to drive in, so I installed the windshield in the hope that it would provide wind protection.
Was the one you received as per Image?
As per Image
Was the installation difficult?
It is easy to install as long as you have a Wrench.
How was your experience with it?
After installation, I went out for touring several times and could not feel the wind protection effect.
Aside from the windshield effect, I think the Meter is now easier to read and looks cooler, so that's a good thing.
View detail
Not much attention to detail.
[How is it used?
NSR250R (MC21) I was going to get a Chinese Cowl, but I was worried about its strength, so I decided to use Material:We decided on the FRP Saiya Cowl.
Was the one you received as per Image?
The finish is well done at first, although the premise is painted.
However, the R and other fine parts are of a certain level of quality, so those who are concerned about them will need to sand to some extent.
Was the installation difficult?
I am worried that it will crack until I figure out the hang, because it will never fit unless I install it so that it slides in from the front at an angle.
The seat rail is very narrow, so it is put in while interfering with the seat rail, so the seat rail is definitely damaged.
I had to cut off a part of the inner fender side.
The hole position was not correct behind the Right, so the hole was re-drilled.
Lastly, a small detail:the hole for the tail lamp was half full, so it was re-drilled.
How was your experience with it?
I had some complaints about the installation and hole position etc., but when I installed it, the Style was exactly as I had imagined it would be.
Naturally, Accessory Cases cannot be used and Tandems are not available, but the rigidity of the case is high and it seems to be free from cracks, etc.
[Included Parts:were they on?
All of the Included Parts:in the description came with it.
There was no OEMBracket to fix the tail lamp, so I had to make my own, but there was nothing missing.
[Was there anything that disappointed you?
I thought the mounting method and hole positions were indeed a bit more solid, but...
I would like to believe that mine was just like that as there may be individual differences.
【Review】
Although processing is required, it is not that difficult and can be installed securely if time is taken.
This is good for those who want to keep the OEMCowl or want to use Original's colors.
View detail
Mounting Large Change
I had a bad feeling about this because there was a hole in the corrugated ball when it arrived, but as I expected, the packaging was not good enough and the corner of the cowl had made a hole in the corrugated ball. I decided to return it and use it as it was since there seemed to be no replacement for it.
I thought 30 minutes to an hour would be enough for installation, but I struggled because the Bolt holes did not fit.
The right side of the washer was fine, but the left side could not be installed due to the thickness of the nylon washer, so it was installed without the washer.
There is a slight gap in the cowl of the car body that is not ExactlyFit, although it may be an individual difference.
ParenthesisIt was a little disappointing because it is a good Part.
View detail
Undercowl
Overall satisfy with the product. Only think I was disappointed, was nicely fit into my bike while cornering hit by road just done my spray work was upset. View detail
Fits: YAMAHA XJR1300, YAMAHA XJR1200, YAMAHA XJR1300, YAMAHA XJR1200
at the expense of
I bought it for the …xjr1300 and because the design and parenthesis were good.
I thought it would be easy to install as it was designed for the xjr1300 so I thought it would be easy to put it on the frame, but … there are some troublesome gold parts and the fit is not good, so I felt like I had to force it on.
View detail
Double-sided tape makes me nervous.
I'm not sure if double-sided tape is enough. I'm afraid it's going to fly away. (Lol) Solder attached. View detail
so-so
Installation was relatively easy, partly due to the use of double-sided tape.
However, it seems to be floating a little and does not adhere well.
View detail