Reviews
Fits: SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI GSX-S1000F, SUZUKI GSX-S1000
Processing is assumed to be Large.
The Instruction Manual states that some modifications may be required, but basically, Dry Carbon, an Other Brand Product, can be installed without modifications in most cases. As usual, this product also requires modification. The remaining 20% will be modified during the installation process.:Pair (for Left and Right) The gap between the two is different, so if you are concerned about the gap, you should refrain from using this product. I had high expectations for this brand because it has been gaining momentum recently, but I have a problem with the outside of Dry Carbon products, including some AEC products. View detail
Small in size, but large in appearance (installed on a 24-year model)
When purchasing the ZX-6R 24th model, the company considered converting the plastic parts to carbon to improve the quality of the appearance.
After comparing images and videos with the 2011 model, we determined that it could be used for the 24th model and purchased it.
Since CR-1Coating was scheduled to be installed as part of the car delivery maintenance, we brought the car to Kawasaki Plaza to have it installed in its installed condition, and the installation was done without any modification.
There were some comments to Review about poor Fitting, but I have no problems with mine.
Although these are small parts, I think they have a lot of impact in terms of appearance.
View detail
Small parts, but looks like large parts (can be installed in 24 years model).
After comparing images and videos of the '24 and '23 MODELs, I wondered if it would be possible to divert it to the '24 MODEL as well. I asked Kawasaki plaza to install it along with the vehicle maintenance.
As a result, they were able to install it without any modification.
I was concerned because some reviews said the Fitting was not good, but the one I fitted seems to be fine.
Although these are small parts, they give a very different impression when installed.
View detail
Well, I guess I'm satisfied.
I think the accuracy is somewhat good, but the Edge is a little hard to hit.
There are some gaps.
View detail
Good quality and fit
Item arrived in a well seal packaging. Workman ship for carbon fiber is very good. The holes aligned correctly and a cushion strip is added to reduce vibration. View detail
Good quality and fit(almost)
Item arrived in a well seal packaging. Workman ship for carbon fiber is very good. The holes aligned correctly mostly except for one hold for the left panel below dashboard. View detail
Seat Cowl connected and Refreshing.
The Seat Cowl is also made of the company's Carbon, which gives a sense of unity.
I was hesitant to buy it because the price was so high, but when I put it on, I was glad that I bought it.
The Rear area is now fully Carbon Spec.
View detail
If only it were a little cheaper lol.
I was hesitant because of the high price, but when I installed it and looked at it, I am glad I purchased it. I had to adjust the screw position to see if it was an individual difference. View detail
Slight modifications were needed.
The twill weave and glossy finish gave it a Gorgeous atmosphere at once.
I will upload a picture of the installation, but there were some areas that were sized over OEM, so I had to do a lot of shaving in the file.
The part protruding from the masking tape is the Oversize part. I cut here and there other than in the picture, but the bolt holes were correct.
If you do not use the OEM product, you can see the overlay.
As is usual with dry carbon products, it would save time and effort when installing the product if it were shipped with a little more fine-tuning after completion of the product. However, even if this is not the case, Parenthesis has a quality that OEM products do not have.
View detail
Very nice!
When installing a new one, the installation stick etc. will need to be purchased separately.
For OEM Product replacement, only this product is required
View detail
Fits: BMW R1200GS Adventure, BMW R1200GS, BMW R1200RS, BMW R1200R
good stuff
excellent workmanship.perfectly fit.motorcycle now look delicious.will buy more and more stuff.no regrets.shipping worldwide super fast View detail
Only looks
Installed on a GSX-R1000R 2019
Color with inferior texture:This is a custom part to replace the tank side cover, which is an unpainted resin part, with dry carbon.
The texture is impeccable, as you would expect from Dry carbon.
Since these parts are relatively large in area, they contribute significantly to the quality of the overall appearance of the car body.
This part has Sponge/Rubber and Surface Fastener attached to it, but SUZUKIOEM Parts are included in the law.
If they went to the trouble of preparing it, I think it would have been better if it had been attached from the beginning, but I feel that just having it securely attached is sufficient consideration.
The bosses, etc., are also in the correct position, and are made by FOR JAPAN MODELMANUFACTURER.
The overall alignment is also fine.
However, the only claw that hooks onto the tank cover at the front of the vehicle body is not present, so this part of the body is slightly wobbly.
(However, since it is Kachica Dry carbon, not OEM's soft and sticky resin, it basically didn't bother me unless I dared to pull it by hand.)
Also, perhaps because it is different along the OEM (?) If this is a problem, you can fill the gap by applying a suitable thickness of sponge to the lumpy part of the tank on the reverse side.
After all, it is a replacement for Cowl, a design component, so functionally it is no different from Large.
Since the original OEM product is resin, there is no weight saving effect, and considering the cost along the road, I think the OEM product is better in terms of functionality.
but the texture improves well for the price.
Also, because it is a SPEEDRA, the weight carbon is a heavy-spec material, unlike the Large and a half weight carbon of other companies' products.:Carbon.
Moreover, this is sold at a discount to other companies. (I don't know how it is at this point, as the price went up a while ago.)
I think this is a very attractive option for those who want to improve their appearance.
View detail
Self-sufficientParts!
This is a replacement for the CarbonFrame panel when the Cowl is installed. It is a dress-up part that is completely focused on appearance. View detail
One nail was broken. It is unfortunate.
When I tried to take it out of the bag after receiving it, one of the nails was sticking out of the urethane sheet it was wrapped in, pointing in a strange direction.
I removed the Seat with a bad feeling and …
The broken nail came with it popping out of the Seat hole.
This was common in the days of SSK, and remained so even after the company name change to Speedra.
The carbon eyes are nice and neat, but the reverse side invisible is a mess.
I think nails are a part of the body that should be strengthened, as they are easily broken even with normal use…
I think I will receive the same one again even if I ask for a replacement, so I will Repair it and use it.
View detail
Perfect, Carbon?
Carbon is the best.
I can only see the SIDE of the Seat, but it is attractive and self-satisfying with Carbon peeking out of its face.
View detail
W more than I expected.
Purchased to increase appearance Impact
There were no distortions and it was more complete than I expected for the price.
Bolted holes on the back are Material:Plastic. But I don't mind because it is an invisible part.
As others have written, threaded hole machining is required.
View detail
Carbon?
The exposed area of Carbon is very small, but it was replaced with Carbon? It is the best MINICustom, though it is self-satisfaction. View detail
I think Carbon is the best?
It is a seat side cover, so the surface that is exposed is very small, but by using carbon, it gives a sense of luxury and I can only say that I am satisfied. View detail
I can recommend it.
Material:I was able to install it properly without any distortion, which is common with carbon products.
The price is lower than OEM, and I can recommend it.
View detail
There was a Wound.
There is no distortion, and I think it is a product with excellent cost performance, but unfortunately, there was a wound of about 3cm on the Left Side Cowl.
I thought about returning it, but I didn't want to wait for months, so I just installed it.
Also, the screw hole was too small, so it needed to be widened.
View detail