Reviews
Cowl mounting holes do not fit
Paint quality is good. It makes it look like a new car! I had to force it on with Tie Wrap or re-drill the holes … I think it may have been an individual mistake, but … I drilled the holes with a Drill and installed it. If you can install it, you will be supremely satisfied. View detail
Poof, a new car!
While replacing and repairing the keyhole of my father's APRIO, which was the victim of an attempted theft, I also replaced the cowl! This is a very large cowl! The old OEM cowl was reborn as a shiny new cowl, and it feels like a new car! If you look closely, you can see that there was some dust in the cowl and the mounting holes did not fit slightly, but it is just a matter of widening the holes and doing some other simple things! The material of the Cowl is not Pe LePera, but the same level of strength as OEM! This is really a Recommendation! View detail
fitment issues
I was excited to recieve this poduct. There are a few fitment issues with these plastics for my af27 dio. The front piece the 4 bolts on the back side only two line up the other two are so far off would need to enlarge holes to make it work. The top headlight piece does not fit well pops out on the one side and on the middle. The rear pieces seems to fit alittle better but not the best. View detail
Very good complete set of plastic
About quality and texture
A high-quality plastic kit for the whole scooter, absolutely all the fasteners are as in the original parts, except for a few points, it is necessary to drill holes for installing a small beak on the main beak, as well as a hole for the output of the spoiler brake light wire on the right sidewall, otherwise everything is fine, full compatibility and easy installation without adjustment and modifications
About the feeling of use
After installation, only positive emotions, absolutely good plastic, perfect fit and beautifully painted, no disappointments, in the photo you can see this kit after unpacking, only the gas tank cap was not included in the frame
Products to buy together
Full set of painted plastic, no additional purchases required, everything fits perfectly
Difficulty of installation
Easy installation, instead of old plastic, all original fasteners are 100% compatible
Cost performance and comparison with other products
Low cost of a plastic kit, but high shipping costs, because this product takes up a large amount of space
About shipping and packaging
Reliable packaging in a box and in a soft material that does not scratch the plastic coating
Any concerns, cautions, or advice when purchasing
Please note that there are holes that are missing on this product, 3 holes need to be drilled ------------------------------ ---------------------------- About Quality and Texture A high -quality set of plastic for the entire scooter, absolutely all the fasteners as in original details, except for several points, it is necessary to drill holes to install a small beak on the main beak, as well as a hole for the output of the Stopsignal of the spoiler at the right sidewall, all the other is fine, complete compatibility and easy installation without fitting and modifications ABOUT THE FEELING OF USE After installation, only positive emotions, absolutely good plastic, perfectly suitable and beautifully painted, no disappointment, in the photo you can see this set after unpacking, only the gas tank cover did not get into the frame Products to Buy Together A full compartment of painted plastic, additional purchases are not required, everything is perfect Difficulty of Installation Light installation, instead of old plastic, all original fasteners are compatible 100% COST Performance and Comparison with Other Products Low cost of a set of plastic, but high delivery cost, TC This product occupies a large amount of space ABOUT SHIPPing and PACKAGING Reliable packaging in a box and soft material that does not scratch the coating of plastic Any Concerns, Countions, or Advice When Purchacing Keep in mind that refinements are needed in the form of holes that are not enough on this product, 3 holes must be drilled Powered by Google Translator
View detail
Fits: HONDA Today, HONDA Today, HONDA Giorno, HONDA DIO(4Cycle), HONDA DIO(4Cycle)
How durable is it?
Restore TODAY after many years of neglect, 4 years.
Will the Fork Boots break off from age?
I couldn't cut it out of my mind…
I noticed a tear and replaced it.
I thought OEM would be better in terms of texture. I thought so.
How long do you think it will last as a consumable?
I would like to verify this.
The protrusion for fixing the drum brake on the LeftFork was quite fiddly.
View detail
So so
I guess it's okay…
The hole position is different or…
Fitting is subtle des…
It is good if you are not particular.
View detail
Great spoiler to replace the original
About quality and texture
Excellent quality of molding and processing of plastic, all corners are made indistinguishable from the original, perfect mounting holes, fits and fastens well to a standard mounting plate
About the feeling of us
The spoiler was pre-painted in white standard color, there was no burr on the surface, the plastic and coating are easy to process, the quality is identical to the factory, even the paint from the factory looks very good, but I needed a different color
Products to buy together
This kit only comes with a plastic spoiler, if you are looking for a replacement plastic part, then this product is for you.
Difficulty of installation
Easy installation in a standard place, instead of a damaged factory part, all mounting holes are identical and perfectly match the mounting plate
Cost performance and comparison with other products
The price is pleasantly surprising, the original spare part is much more expensive, however, the quality corresponds not only to the price, but also to expectations
About shipping and packaging
Packed in soft packaging, but Webike additionally packed and protected the item from damage during transportation
Any concerns, cautions, or advice when purchasing
Please note that there are only two kinds of color, black and white, the parts are factory painted with a good coating, so if you need a different color, then be prepared for additional painting -------------- -------------------------------------------------- About Quality and Texture Excellent quality of casting and processing plastic, all angles are indistinguishable from the original, ideal fasteners, a standard fastener is well suited and fixed ABOUT THE FEELING of US The spoiler was previously painted from a white standard color, no burrs were on the surface, plastic and coating are easily processed, the quality is identical to the factory, even the paint from the plant looks very good, but I needed a different color Products to Buy Together Only a plastic spoiler is delivered in the kit, if you are looking for a replacement of a plastic part, then this product is for you Difficulty of Installation Easy installation in a standard place, instead of a spoiled factory part, all fasteners are identical and perfectly suitable for a reckoning plate COST Performance and Comparison with Other Products The price is pleasantly surprising, the original spare part is more expensive, however, the quality corresponds not only to the price, but also to expectations ABOUT SHIPPing and PACKAGING Packed in soft packaging, but Webike additionally packed and protected the part from damage during Any Concerns, Countions, Or Advice When Purchacing Pay attention to the fact that only two types of color, black and white, the details are painted at the factory with a good coating, so if you need a different color, then be prepared for additional painting Powered by Google Translator
View detail
Fits: HONDA SUPER CUB 90, HONDA SUPER CUB70, HONDA SUPER CUB 90, HONDA SUPER CUB70
Scratches are common on side covers.
KICK-started CUB, side cover was replaced because after 20 years of riding, it was too scratched to look at.
OEM compatible.
I think the color is slightly different.
good point
Cheaper than OEM.
Easy installation due to interchangeability.
Plain, so it can be personalized with Sticker or Emblem.
A bad point
● I think there is a little BALI.
If you start KICK, you'll get scratches all over it without even knowing it, so if you're worried about it, replace it or paint it. This is cheaper than painting.
View detail
Fits: HONDA DIO(4Cycle), HONDA DIO(4Cycle)
If you're okay with it, you can buy it.
[Intended use]
The exterior of AF68 DIO that I got from an acquaintance was tattered, so I took a chance and bought it.
[How is it used?
1000km since I bought it.
Was the one you received as per Image?
The exterior Parts of the Other Brand Product were as Image in a bad way.
I had heard stories about how the dust didn't fit.
First of all, there were many White scratches on the surface even before I took the product out of the DanBall. The BALI of the mounting holes is also terrible.
Was the installation difficult?
The mounting holes do not match by any stretch of the imagination.
There are a few places here and there where there are no holes when compared to OEM.
On top of that, I got a triple Combo:no Instruction Manual.
If the hole doesn't fit by any means, I use Tie Wrap to stop it.
How was your experience with it?
The surface could be put on like that, so I'll give it a minimal circle.
[Included Parts:were they on?
None
Bolts have to be diverted from OEM.
[Was there anything that disappointed you? Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
[Availability and clarity of the Instruction Manual
I can't talk about it because it's not attached in the first place lol.
[Point and hang of installation].
You have to install it with your spirit.
If the hole doesn't fit, Tie Wrap it!
[Opinions and requests to Manufacturer
I doubt the quality of the manufacturing. I wonder what kind of dimensional instructions they put in to make such a terrible product.
View detail
Fits: HONDA LEAD 100, HONDA LEAD 100, HONDA LEAD 50, HONDA LEAD 50
It's not OEM Product!
This product is not an OEM Product.
It certainly does not say OEM in the product description.
I had my doubts about the Gold amount, as it was quite low.
I think that should be included as an explanation.
The workmanship was not as good as it looked and I was quite disappointed.
Haven't installed it yet, but hopefully it will fit nicely.
It would be a disaster if this didn't get attached.
View detail
Fits: HONDA LEAD 100, HONDA LEAD 100, HONDA LEAD 50, HONDA LEAD 50
Poor Webike support
I order a product, but I can't proceed because I'm checking with my supplier.
That sucks.
If you can't do business, then stop.
View detail
No harm in having it! Surprisingly firm Cowl
I've been riding PCX for about 5 years now.
From daily commuting to LightTouring and snowmobiling, SmallWound has been increasing.
He is a very good boy and I want to continue to drive him for a long time, so I bought Cowl as a spare.
When they arrived, each one was individually wrapped and secure, but I was surprised to find that the corrugated cardboard was large.
The shipping would have been expensive.
I opened it up and the quality is as good as the OEMCowl.
The surface is also well Lame processed, and I was surprised that it was amazing for this price.
As is the case with all motorcycles of this class, the claws that hold the cowl in place often break during operation, and 1 pcQuantity:If it's 2pc or so, it's no problem, but if 2-3 pieces are broken, you can't install it.
I have no plans to replace it in the foreseeable future yet. I bought this as a spare as similar products have been noticeably discontinued.
I was wondering if there was anything else that was this cheap.
View detail
Let's save up before it's gone.
I bought this for the exterior of my 2012 PCX.
It's not that it was cracked, but I bought it because I thought that the day when I can't get the exterior at this price is near because SmallWound and Crack are seen in some places due to too much severe environment and new PCX is coming out rapidly.
[How is it used?
It looks like the current exterior will hold up for the time being, so it will be fertilized by Chest for a while.
Was the one you received as per Image?
I was surprised that the paint was more solid than I had imagined.
Lame processing? If you don't compare it well, you can't distinguish it from OEM.
Was the installation difficult?
I haven't installed it yet.
However, the claws that hold the Cowl in place are really easy to break, so if you're planning to work on it, please be very careful!
[Included Parts:were they on?
It came with a large piece of corrugated cardboard. (PACKING)
If you could just sum it up for me...
[Was there anything that disappointed you?
It was better than I was expecting.
If I had to guess, I'd say 、、、、 Ummm...
Other items that would be helpful
Items to buy together
→ Let's buy a lot of things together at this time.
View detail
Fits: SUZUKI ADDRESSV125, SUZUKI ADDRESSV125
perfectly
Well packaged and easy to install.
It has been reborn as a new product.
View detail
Same as OEM Product etc.
It didn't have the exhaust cover on the SEA BASSLETS4, so the OEM was not included When I searched for parts, I couldn't find the part number and gave up on it, but I found this Cover I found the
Material:I was a little apprehensive about the Plastic, but I'm happy with it because it looks light and strong
View detail
Fits: SUZUKI ADDRESSV125, SUZUKI ADDRESSV125
It's not too much for the price
I'm not an OEM, and the price is low, so I was just hoping it would look a little better I was going to add the Pillion Bar for the Spoiler as well, but it's a very well made thing And I was surprised
Large Satisfied with the product
View detail
New front
My bike is look like new again. The front cover has a beautiful black shine. Fast posting and well-packed. I'm really satisfied ! :) (The sticker on the middle of nose was not part of the item.) View detail
NBS JAPAN Fusion Exterior Black
NBS JAPAN Fusion Exterior was cheape but value was super. Paint job was good and clear without any problems. Easy to assembly. No need for extra tools. The colour fits the well with the Ai-net Under Cowls. View detail