Reviews
![[NATIONAL CYCLE:National Cycle]Vstream Windshield](https://img.webike-cdn.net/catalogue/images/75533/16971_TS.jpg)
Fits: HONDA PCX150, HONDA PCX
Windproofing, though.
As far as I have been able to find out, I think this item is the LARGEST as a windshield. (At the time of purchase)
I think the windproof effect is solid in the Large size range.
However, in the summer, when parked in the sun, the light was concentrated on the Screen and the inside of the Screen melted.
It is possible to countermeasure this problem by placing Towel or other material between the two, but be careful, as the entire Towel may burn if it is not properly placed.
View detail
Increased windshield effectiveness.
I purchased this product for the purpose of reducing wind effects when driving at high speeds.
OVER Separate Handlebars interfere with the Throttle Cable and the Tank of the Master Cylinder.
Handlebar is installed back to OEM (without Spacer).
Well nuts (C-440) are used to join the Base and Screen sections.
The experience of installation is that the posture is shallower than OEM, where the benefit of drag reduction is achieved.
The effect is not that noticeable in the normal posture, but the reduction was noticeable in the sticky prone position.
About the appearance (FRP Black, [Color] (Select Option in Clear)
The Luster feel is good, but as you can see from the light reflection in the Base area in the photo, the surface preparation is a bit lax.
if you are concerned about [Color] It is best to purchase without Clear and paint after priming.
The Screen section is not distorted in any strange way, and it is nice to know that this is also available as a Single Body.
It seems to be #Made-to-Order, so the delivery time may take a couple of months.
View detail
Satisfied with Simple Design
One month has passed since the product was installed, and the height is definitely 4 cm higher than that of the OEMScreen, and I am satisfied with the simple design that does not give the impression that it is just for show. However, the OEMScreen has a step between the cowl and the screen, so there is no difference between the screen and the cowl, but this product has no step between the cowl and the screen, so there is a difference between the cowl and the screen. In addition, the product has a quantity of Screen mounting screws.:Since it is not set, the Screen mounting Screw must be ported from OEMScreen or prepared separately. View detail
Just right.
OEM is too low and I want a little more height, but too high and it looks like Tourer, so +1.5 MARC is just right.
I prefer sharp designs to rounded ones.
[Color] Smoke so it has good visibility even when it is face down.
View detail
As generally expected
I bought this for RonTwo.
Alafi Return.
Before Return, I had only ridden Vixque and rarely rode at high speeds, so I did not understand the large aerodynamic drag of a naked motorcycle at high speeds.
I was not convinced that it was hard to run at legal speeds due to the large aerodynamic drag of the bike, even though the bike can reach the legal speed limit at high speeds in Japan without even half the speed of the Meter.
My impression is generally in line with expectations.
For driving at legal speeds on highways, the resistance is reduced considerably and it is easier to drive. Plusα speed when overtaking is also much easier, and is generally as expected. The height of the screen is a little lower than my eye level.
The only thing I feel a little minus is that the wind, which seems to come from the slit in the center, just touches the top of the helmet, and I feel a lot of noise and vibration. Once you get used to it, it's not so bad, but it's a little too large and at low speeds, it's not so bad. (in town) But I can feel it, so it might bother some people.
What was surprising was that it was originally attached to the MeterCowl as well, [Color] I was going to buy Smoke, but because of inventory and because I was going to remove it when not doing basic RonTwo, [Color] I bought the Clear, but the Screen picks up the light from the Headlight and the whole thing glows dimly. I don't drive much at night, but I think it's quite beautiful.
View detail
[Color] Smoke Screen
Installation was easy, even for an amateur. With a good density, (in Tokyo) I could see in front of me even at night, the Large size was just right, and the wind hit me not hard at all at 100km/highway cruising. View detail
I put it on to keep the bugs away.
With OEMScreen, the insects hit my neck, so I wanted a slightly largerScreen and chose VS-14.
The objective was successfully achieved and the insects no longer collided with the neck.
It came with a warning to do the Cover when parking in direct sunlight, but honestly, it's a hassle and I'm going to try using it without it until I have a problem.
Is there a real problem or not...?
View detail
Windproofing effect Extremely Large
Even OEMScreen's windproofing was generally satisfactory.
However, he purchased this product for further wind protection.
The installation was very easy. 30cm of distortion during molding was found in the vertical direction as a minus point.
The key windproofing effect is immensely Large. At high speeds it becomes (almost) windless. It may be hot in summer.
Also, the material seems to be acrylic, so I am concerned about deterioration over time.
View detail
Fits: HONDA CRF250L, HONDA CRF250M, HONDA CRF250L(S), HONDA CRF300L
Hokkaido Tour
this summer
Hokkaido Touring Schedule
Little by little, we prepare for that.
Removed for forest road touring
with ScreenKakeTamaMaju I can't mock up comfortably.
Easily removed by PointUp??
View detail
Windproof effect.
There are many videos on youtube etc. for installation, so you can install it while referring to them. As for the windproof effect, it has a windproof effect from half of my face to my chest area. The Demerit has a screen that creates turbulence, which causes the head to shake when the wind blows against the helmet. The height and angle of the screen must be adjusted as often as possible to avoid turbulence. It is not enough to just raise the screen, but it is better to adjust the image so that the turbulence hits the entire helmet and the wind pressure is dispersed throughout the helmet. It is not easy to adjust the helmet, but I like it because it reduces fatigue during long tours, and it also makes the helmet look more like a travel helmet. View detail
Easy to use as OEM compatible without distortion
Used on ZZr1100 (C1).
The OEM screen was damaged from the attachment point due to age-related deterioration, so MRA's screen was introduced this time for the purpose of repairing it. [Color] Clear? [Color] I was wondering if it was Smoke or not, but this time I decided to use it as a makeover. [Color] Smoke.
The OEMScreen is slightly thinner than the OEMScreen, but has less distortion than the OEMScreen, and has good visibility even when it is tucked into the cowl.
However, Smoke Screen is darker in color than I had imagined, and I think it would be tough to run face down with Smoke Shield's Helmet late at night.
A Screen RimRubber was also included and its length was appropriate and favorable.
I am glad to see that they are making parts that fit older motorcycles as well, as screens wear out due to scratches from flying rocks and need to be replaced periodically. Next time I will try Clear Screen.
View detail
Essentials for commuting to work and school
We installed this Screen (RS) on an ADDRESSV125S.
I found that the wind does not blow directly against my body during winter driving, which reduces the coldness I experience.
Also, when driving in the rain, the logic is the same and comfort is improved.
View detail
No need to attach the phone Folder to the Handlebar and it is easier to turn the keys!
First of all, I feel that Eliminator has become taller and Parenthesis has improved (laugh). The windproof performance is not high and the width is slim, so the wind is coming in from the side of the Shield. For those who value performance, we recommend a wider width. I guess it is better to have it than not to have it. What made me happy was that I had attached the Smartphone Holder to the right hand side of the Handlebar, so I had to stick my hand into the narrow space and turn the Engine key, but when I moved the Holder to the Clamp Bar, I found that the keys around the Holder were refreshed and the Holder was much easier to use. But when I moved the Holder to the Clamp Bar, the key area was refreshed and the Stress was gone! I was able to install it even as an amateur while reading the instruction manual. However, as the instruction manual also warned, the Assembly is somehow prone to cracking! I also have a quantity:2pc. I broke one of the set points and had to use superglue, so you might want to have some ready just in case. I am thinking of adjusting something because I hear a chattering sound when I run after installing it. View detail
![[Repair Parts] Handlebar Clamp Fitting Set for Repair](https://img.webike-cdn.net/catalogue/images/116615/43363_TS.jpg)
Fits: Others For UniversalScreen
Repair Parts are well stocked.
I had only the Screen, so I purchased only the Repair Parts and was able to install them.
The installation was easy to understand because the Instruction Manual can be downloaded from the website.
The feeling of using it is not a problem with wind pressure, though, as I have used it before,
The Cap of Included Parts:has the BALI in the image, which was prepared with a Cutter Knife and then installed.
The installation points are the Clearance and Angle of the Screen and the Light, which change the appearance of the Motorcycle.
As a request to the manufacturer, we would like to sell only the Spacer, which is attached between the Handlebar and Clamp, as a Single Item.
I was so satisfied that I Repeat both Left SideRight Side.
View detail
Effective for high speed drivingLarge
I used to install something smaller than No Brand's Blast Barrier, but the Blast Barrier is superior in both form and effect. It is especially effective at high speeds. View detail
Performance Expectations
The OEM wanted a longer Screen because it felt like the wind hitting the Helmet was swirling around my chest. [Color] Since it was clear and with color, and since we are thinking of installing a handlebar riser in the future, we decided to go with this product because it was slimmer than other manufacturers and there was word of mouth on a certain site that it is difficult to interfere with the handlebar when it is cut off. The length was +7cm compared to OEM, but it seemed to be measured at the largest length of each, and there was about +11cm at the center position where it was actually installed. Although I have not actually driven the car due to poor weather conditions, I can expect that the wind will have much less effect on the car. View detail
It is unfortunate that the Sticker or company name is not specifically mentioned or attached!
I thought it would be good to add a Sticker or something to promote the product.
Also, I think it would be better to use a nicely painted Washer for the Screen installation if possible. (Currently, it is roughly painted Black)
Since the Gold amount is 30,000 yen, I was hoping to clean up the details if possible!
View detail
I'm glad I bought it
The length was better than other companies' external screens because it was more windproof.
However, there is a possibility of interference depending on the installation position of the Smartphone Holder.
View detail
Looks like OEM.
To install, simply remove the two screws, put them on, and tighten the two screws again.
It's very simple
Design as if it were OEM.
I still feel that the design of Mt series is completed by adding Shield.
View detail
Parenthesis is good!
I was torn between OEMOption and ACRYPOINT.
I am glad we chose this one.
The texture is good and I think Parenthesis has improved on its own.
I'm glad I bought it
View detail