Reviews
[Color] Smoke Screen
Installation was easy, even for an amateur. With a good density, (in Tokyo) I could see in front of me even at night, the Large size was just right, and the wind hit me not hard at all at 100km/highway cruising. View detail
I put it on to keep the bugs away.
With OEMScreen, the insects hit my neck, so I wanted a slightly largerScreen and chose VS-14.
The objective was successfully achieved and the insects no longer collided with the neck.
It came with a warning to do the Cover when parking in direct sunlight, but honestly, it's a hassle and I'm going to try using it without it until I have a problem.
Is there a real problem or not...?
View detail
Windproofing effect Extremely Large
Even OEMScreen's windproofing was generally satisfactory.
However, he purchased this product for further wind protection.
The installation was very easy. 30cm of distortion during molding was found in the vertical direction as a minus point.
The key windproofing effect is immensely Large. At high speeds it becomes (almost) windless. It may be hot in summer.
Also, the material seems to be acrylic, so I am concerned about deterioration over time.
View detail
Fits: HONDA CRF250L, HONDA CRF250M, HONDA CRF250L(S), HONDA CRF300L
Hokkaido Tour
this summer
Hokkaido Touring Schedule
Little by little, we prepare for that.
Removed for forest road touring
with ScreenKakeTamaMaju I can't mock up comfortably.
Easily removed by PointUp??
View detail
Windproof effect.
There are many videos on youtube etc. for installation, so you can install it while referring to them. As for the windproof effect, it has a windproof effect from half of my face to my chest area. The Demerit has a screen that creates turbulence, which causes the head to shake when the wind blows against the helmet. The height and angle of the screen must be adjusted as often as possible to avoid turbulence. It is not enough to just raise the screen, but it is better to adjust the image so that the turbulence hits the entire helmet and the wind pressure is dispersed throughout the helmet. It is not easy to adjust the helmet, but I like it because it reduces fatigue during long tours, and it also makes the helmet look more like a travel helmet. View detail
Easy to use as OEM compatible without distortion
Used on ZZr1100 (C1).
The OEM screen was damaged from the attachment point due to age-related deterioration, so MRA's screen was introduced this time for the purpose of repairing it. [Color] Clear? [Color] I was wondering if it was Smoke or not, but this time I decided to use it as a makeover. [Color] Smoke.
The OEMScreen is slightly thinner than the OEMScreen, but has less distortion than the OEMScreen, and has good visibility even when it is tucked into the cowl.
However, Smoke Screen is darker in color than I had imagined, and I think it would be tough to run face down with Smoke Shield's Helmet late at night.
A Screen RimRubber was also included and its length was appropriate and favorable.
I am glad to see that they are making parts that fit older motorcycles as well, as screens wear out due to scratches from flying rocks and need to be replaced periodically. Next time I will try Clear Screen.
View detail
Essentials for commuting to work and school
We installed this Screen (RS) on an ADDRESSV125S.
I found that the wind does not blow directly against my body during winter driving, which reduces the coldness I experience.
Also, when driving in the rain, the logic is the same and comfort is improved.
View detail
No need to attach the phone Folder to the Handlebar and it is easier to turn the keys!
First of all, I feel that Eliminator has become taller and Parenthesis has improved (laugh). The windproof performance is not high and the width is slim, so the wind is coming in from the side of the Shield. For those who value performance, we recommend a wider width. I guess it is better to have it than not to have it. What made me happy was that I had attached the Smartphone Holder to the right hand side of the Handlebar, so I had to stick my hand into the narrow space and turn the Engine key, but when I moved the Holder to the Clamp Bar, I found that the keys around the Holder were refreshed and the Holder was much easier to use. But when I moved the Holder to the Clamp Bar, the key area was refreshed and the Stress was gone! I was able to install it even as an amateur while reading the instruction manual. However, as the instruction manual also warned, the Assembly is somehow prone to cracking! I also have a quantity:2pc. I broke one of the set points and had to use superglue, so you might want to have some ready just in case. I am thinking of adjusting something because I hear a chattering sound when I run after installing it. View detail
Fits: Others For UniversalScreen
Repair Parts are well stocked.
I had only the Screen, so I purchased only the Repair Parts and was able to install them.
The installation was easy to understand because the Instruction Manual can be downloaded from the website.
The feeling of using it is not a problem with wind pressure, though, as I have used it before,
The Cap of Included Parts:has the BALI in the image, which was prepared with a Cutter Knife and then installed.
The installation points are the Clearance and Angle of the Screen and the Light, which change the appearance of the Motorcycle.
As a request to the manufacturer, we would like to sell only the Spacer, which is attached between the Handlebar and Clamp, as a Single Item.
I was so satisfied that I Repeat both Left SideRight Side.
View detail
Effective for high speed drivingLarge
I used to install something smaller than No Brand's Blast Barrier, but the Blast Barrier is superior in both form and effect. It is especially effective at high speeds. View detail
Performance Expectations
The OEM wanted a longer Screen because it felt like the wind hitting the Helmet was swirling around my chest. [Color] Since it was clear and with color, and since we are thinking of installing a handlebar riser in the future, we decided to go with this product because it was slimmer than other manufacturers and there was word of mouth on a certain site that it is difficult to interfere with the handlebar when it is cut off. The length was +7cm compared to OEM, but it seemed to be measured at the largest length of each, and there was about +11cm at the center position where it was actually installed. Although I have not actually driven the car due to poor weather conditions, I can expect that the wind will have much less effect on the car. View detail
It is unfortunate that the Sticker or company name is not specifically mentioned or attached!
I thought it would be good to add a Sticker or something to promote the product.
Also, I think it would be better to use a nicely painted Washer for the Screen installation if possible. (Currently, it is roughly painted Black)
Since the Gold amount is 30,000 yen, I was hoping to clean up the details if possible!
View detail
I'm glad I bought it
The length was better than other companies' external screens because it was more windproof.
However, there is a possibility of interference depending on the installation position of the Smartphone Holder.
View detail
Looks like OEM.
To install, simply remove the two screws, put them on, and tighten the two screws again.
It's very simple
Design as if it were OEM.
I still feel that the design of Mt series is completed by adding Shield.
View detail
Parenthesis is good!
I was torn between OEMOption and ACRYPOINT.
I am glad we chose this one.
The texture is good and I think Parenthesis has improved on its own.
I'm glad I bought it
View detail
Windshield effect is best, but
Installation was easy, but if you make a mistake in the setup, you will end up with minor scratches on both ends of the lower inside of the Shield.
The running and wind protection effect is very good.
However, the Shield is so close to my face that when I apply emergency braking, the Shield tip almost sticks me in the face.
If you have a Helmet Shield, you are safe, but if not, you will injure your face and eyes.
We are considering installing a molding around the Shield as a countermeasure.
View detail
Fits: HONDA CB125R, HONDA CB125R, HONDA CB250R, HONDA CB150R, HONDA CB300R, HONDA CB150R, HONDA CB300R
cb250r is now a handsome man.
I felt the wind much more with Ron Two as soon as I bought the cb250r.
The ninja250 was a Full Cowl, so of course it was equipped with Screen and I rode it without any complaints.
There was also a long size, but I decided to go with this one because of its appearance.
I compared driving without and with the new system, and the difference was totally different.
Like the wind avoided me lol.
Meter is clearly visible.
View detail
The top edge comes up to my eyes and bothers me a little.
I have been using Puch's Screen since the nc750x on all my cars and am comfortable with the quality. The wind tunnel tests have been done, so the effect is perfect. The wind is blowing over the helmet. The screen is also equipped with a hand guard, so the wind does not hit my hands. However, the upper edge of the screen is just above the eyes, which is annoying. It is hard to see at night even through light smoke. 173cm average body type should be prepared for this. View detail
expensive
The wind protection against wind hitting the upper body makes a difference in the fatigue level when touring.
I am satisfied with the design as it does not detract from the style of the SV.
However, I think the price is too high. I thought it would be easier to buy if it were cheaper.
View detail
The product is Well, and a good impression is made!
The product is designed to be used with the thickness of the Screen and [Color] I think that both the Smoke and the accuracy of the BKT installation are good.
[Color] We chose the darkest Smoke and the most expensive Screen, and we like them in terms of design.
The darker screen provides well forward visibility even when it is cloudy in the daytime, and I feel that the height of the screen is also necessary if you want windproof effect.
Screen strength also seems to be fine at CircuitLevel Speed.
The only reason I couldn't give it more than one star is that there were no instructions on how to install it and I couldn't figure out the proper way to install it.
I used 4 bolt nuts on the Headlight BKT and modified the included BKT a little to install it, but I feel that this method is better in terms of strength.
Overall, I believe we have completely fulfilled the need for increased windproofing while maintaining helicopter TESIStyle.
View detail