Reviews
Fits: KAWASAKI NINJA H2R, KAWASAKI NINJA H2, KAWASAKI Ninja H2 SX SE, KAWASAKI NINJA H2 SX
Slightly difficult to shape and install
At the time of purchase of the Rear Fender of the company, the Image around the Swing Arm
I bought this along with the Swingarm Guard to unify them.
It is made much thicker than other Parts, and it is very chunky.
The strength is considered to be quite high.
It is a shape, but the edge of each side seems to come out in the photograph, but it is a shape that arrives
The outline of Parts is the same as OEM, but there is almost no edge on each side.
It was a rounded shape.
This may be the case with this one, but it is the same as the picture, H2SX!
I thought it was similar to the OEMParts with the Edge effect of the
I was quite disappointed.
In addition, when it installs, OEM is made along the Swing Arm shape, and there is a sense of discomfort.
It is not, but this seems to be attached distortedly because of the shape that the part is a little off.
It looks like
If you look at the parallelism between the Chain and the Body, you will see that they are parallel.
It doesn't seem to be wrong.
I can understand a little gap if it is a large size part, but for a part of this size.
I felt that the details were a little sweet.
Installation is the most difficult of the three Parts I purchased this time.
The addition itself is just a matter of widening the hole a bit to allow the OEM collar to pass through.
If you don't find the right direction to spread the bolt, it will be difficult to tighten the bolt.
There are two Bolt locations, one on the side and one on the bottom.
First I removed the OEM, then I aligned it and tried to find a direction to widen the hole.
It is better to
If the Bolt is misaligned as described above, it will be difficult to tighten.
However, if the collar is made into a long hole, it will not fit in the hole.
It is thought that it does not stop tightly.
Once the hole expansion is complete, run the OEM Color through the RubberWasher that comes with the
Insert the bolt from the reverse side into the hole of this part, as opposed to the OEMParts installation.
Stop.
There is one point to note when removing the OEMParts and installing thisParts.
The Bolt here is quite hard because of the powerful screw lock agent.
Also, the lower Bolt stops at a slight angle from front to back.
Therefore, it is necessary to make sure that the direction of the screw and the position of the hex do not deviate when removing and installing.
Make sure the bolt direction is straight and push it in firmly to turn.
The Bolt has a slightly low head, so the Hex is shallow, and if you're not good, the Bolt's
It will lick the hexagonal part.
View detail
Fits: KAWASAKI NINJA H2R, KAWASAKI Ninja H2 SX SE, KAWASAKI NINJA H2 SX, KAWASAKI NINJA H2, KAWASAKI NINJA H2R, KAWASAKI Ninja H2 SX SE, KAWASAKI NINJA H2 SX, KAWASAKI NINJA H2
Installation is Large
The holes are not in the right position or thickness.
Anyway, the adjustment is Large strange.
The included RubberWasher makes no sense.
It is written in the Construction Manual that the holes may need to be adjusted, but it is not that Level.
View detail
Fits: KAWASAKI ZZR1100, KAWASAKI GPZ900R
Can't you just half install it?
I'm looking forward to installing it on my zzr1100, and I'm surprised!
I can't reach the front attachment point.
The back part only sticks here …
For zzr1100 and zzr1100 Swing Arm cars... wasn't my zzr a zzr? (Laughs)
There seems to be a difference depending on the year, but they don't seem to grasp that since it even comes with an installation screw.
But I was willing to pay the price to buy a curved aluminum plate at this price if I wanted to imitate it
It's a shame you can't get it right.
I wish you could respond to this in some way.
If you're just sorry for the text, well, that's just the way things are.
I think that's about it.
For now, we will produce the installation part with the aluminum plate.
View detail
Fits: YAMAHA XT250X, YAMAHA XG250 TRICKER, YAMAHA SEROW250
high
Why is it so expensive to just put something over OEMGuard …
If you make the wrong bolt length, you'll hit the Sprocket and you'll be in for a hell of a mess!
It was a rip-off
That's why Zita is …
View detail
Making that it can not be thought of as a very exclusive item
Installation is very easy by saying Chain guard of type fixed with Screw. I bought Carbon's ones and liked it - - -. I noticed that the shape did not fit at the time of installation. I can not install it, Swingarm and Chain guard do not fit neatly in parallel like the sample photos (Chain guard itself has no problem). It looks bad like a picture because it sticks diagonally without sticking in parallel. I can not recommend it if you buy it with an appearance emphasis. View detail
opening packing, although he wanted to use a Carbon tone and bought it -- -- obtaining -- ? -- I thought Carbon ??? with it being true. Since it seems that a certain plastic goods molding were carried out when the rear face was seen, they are h
opening packing, although he wanted to use a Carbon tone and bought it -- -- obtaining -- ? -- I thought Carbon ??? with it being true.
Since it seems that a certain plastic goods molding were carried out when the
rear face was seen, they are honest comment to Be probably a Carbon
.
Since it arranged without processing about
attachment, it is O.
It is whether lightness seldom changes that it is pure.
View detail