Reviews
Axle Slider
Easy installation, just insert and tighten up, but the instructions are not good and some washers need to be added to tighten up. Looks good. View detail
Anyway, I'm not going in.
Quantity:Pair (for Left and Right) Both thought it was SMark, but … it wasn't.
I managed to get it in after considerable pounding with a mallet, but after that, when I moved the Tire, it sounded like it was rubbing somewhere, which was a failure.
It looks like it would be better to have it done properly at Shop.
View detail
Fits: SUZUKI GSX-S1000, SUZUKI GSX-S1000 GT
Before installation, there is a conundrum.
It could not be installed on Axle Shaft as is.
Shaft insert is Quantity:Pair (for Left and Right) Since it is the opposite, the Protector cannot be installed (press-fit) unless it is replaced.
I will have to ask Motorcycle shop to replace the Shaft when I replace the Tire.
(It's a pain to have to pay for labor)
I am very disappointed that I cannot install it even though I ordered it and it arrived the next day.
P.S. I checked MotorcycleCatalogue and all applicable Motorcycles were Nut side Left.
Please note that those who purchase
View detail
Fits: SUZUKI GSX-S1000, SUZUKI GSX-S1000F, SUZUKI KATANA
Rear one place was loose.
Rear parts were loose. The rear parts were loose, so they were adjusted by Seam. View detail
Fits: YAMAHA MT-09, YAMAHA MT-09 TRACER, YAMAHA MT-09, YAMAHA XSR900
Considering a replacement
I bought it because I thought it looked Cool.
But why is it made this way and why is it installed this way…
This product is not available in quantity:Pair (for Left and Right) Separate.
It is better to go through Shaft1 pc.
The inside and outside are tightened with a hexagonal screw, but the outside is made of a plastic-like material, so I tightened it slowly, but it was stuck.
Also, removal is difficult to do.
It is better if it can be removed easily because it has to be removed when changing Tire or putting up a Chain.
I installed it today and am considering replacing it.
I can't recommend it highly enough.
View detail
Unlike Front, Quantity:Pair (for Left and Right) There
I put on Rear Axle Protector, although there are pros and cons.
The image is after installation, but it is not very noticeable and looks good.
The damage may increase due to the longer sliding distance, or it may get stuck and increase the damage due to the lever principle, but we assume that the speed is not too high.
It is a 13mm Nut, but normal Glasses cannot be tightened because the Nut goes inside.
Also, when you close the Quantity:Pair (for Left and Right) If you don't tighten it evenly etc., one Bolt will pop out.
Unlike Front, Quantity:Pair (for Left and Right) There is a
I haven't experienced the effects. No effect." The company is committed to
I hope you don't feel it.
View detail
The Frame is subtle, long, and poorly made.
The length of the Frame is too appropriate. The actual product is quite small. View detail
I wasn't on the rear.
The front was attached by another manufacturer, but the rear was not attached, and I installed it so that the Swing Arm would not die when I fell.
The installation itself is simple with the ScrewShaft and Nut tightened from both sides.
If I wanted to, it would be easier to thread the hollow shaft and bolt it in place.
I also added it and the Maintenance Stand is now harder to use:。。。。
View detail
A bit of a disappointing product…
Slider's bracket has screws on both sides, so it's hard to screw it in evenly. Also, there was only one Cover for Nut in the box. Because I avoided the hot season, I gave up and installed it as it was because two months had passed since I bought it. It was cheap but a little disappointing… (>_<) View detail
The Screw doesn't fit.
I think things are good, but the Pitch on the Screw didn't fit, so I bought a Screw and put it on. View detail
It didn't come with a Nut Cap.
I have no complaints about the product itself.
However, I'm not convinced that one of Nut's PlasticCap shown in the product image was included.
Also in the Handling Instruction Manual. "using nut and cover it with plastctic cap I'm writing to say, … what do you mean?
The front one was attached, so it was even more mysterious.
I'm going to ask if you can send me just the Cap, but I'm not sure.
View detail
Fits: KAWASAKI Z1000, KAWASAKI , KAWASAKI ZRX1200DAEG, KAWASAKI ZX-6R
Bolt is a little short
2020 ZX-6R, 2BL-ZX636G.
The length of the bolt is not enough. I installed it with No Color for now.
I'll go look for Bolt ….
View detail
It didn't help.
When I fell over, it tore off and flew off, leaving the part that was tightened up by the Bolt. The part that was torn off was not damaged so much, and I think that it flew away before it did not play a role in damage-reduction very much. View detail
OEMs are expensive
I bought it because it's a pure product and I trusted it.
I was disappointed because the Material was cheap for the price.
I'm not sure if it will help in the event of a fall.
As expected of an OEM Product, it looks okay.
View detail
Fits: YAMAHA FZS 1000 Fazer 01-05
It appears to be a very old stock item
I don't know if the Motorcycle is old, but it seems to be a very old stock item
I bought Gold, but it's not glossy at all, and it's clearly not Gold
It's very disappointing I should have used something like Black with no color influence
And the worst part is that the Nut hole is unusually small, and the 13mm Socket The wrench does not come in
I've fixed it with radio pliers and turned the Body, but it's not completely tight Anxiety
I had to grind the 13mm Socket with Grinder to make it tighter But no matter how thin it was, it just wouldn't fit Give me back my Gold!
I regret that I could have used a domestic Universal Product
View detail
I couldn't install it because the Shaft was not long enough
The general comment is correct, the Shaft is not long enough and comes out of the insertion slot on the other side of the closing I'd like to.. It was not long enough to fit As you can see in the photo, it's only this length that comes out, so it's just a matter of fixing the Bolt The Screw length is insufficient; check with HondaDREAM I ended up returning this product and replacing it with a similar product from Ditna View detail
Fits: SUZUKI GSX-R125, SUZUKI GSX-S125, KAWASAKI NINJA400 (2014-)
Expectations Ha Gap for the price
Hexagonal because the material of the cap's fastening part was plastic When I tightened it with the wrench, it was easy to lick and spin around So I can't tighten it firmly View detail
I can't put it on, so it's out of the question
The Left Side can be attached to the Left Side with the included parts, but
I can't physically attach the Right Side I couldn't attach it no matter what I tried
I've contacted the Manufacturer, but I thought you could put it on as is The reply, "I don't seem to know much about it The accompanying Instruction Manual also only explains the Slider on the Left Side No explanation for the Right Side, I thought it was defective, but Included Parts:No explanation for the Right Side Included:No description of the Left Side Slider, I thought it was defective, but it was only the bolts that fit the Left Side Slider
I've tried wearing it for a couple of hours, but it's impossible
This is the first time ever that I can't put it on even though it's a special product
View detail
Fits: YAMAHA MT-10, YAMAHA YZF-R1, BMW S1000RR, HONDA CBR1000RR, BMW S1000R
It is not conforming
It is set to s1000rr 2015 but the Largeness of Shaft's hole is Quantity : Pair (for Left and Right) Conversely, Large Slider comes to the Silencer side.
Because I'm bothered, I left it until the Tire exchange, but the direction of Shaft is Quantity : Pair (for Left and Right) The effect seems to be small unless it is changed.
View detail
It attached to 03 model 250SB in preparation for !. As it is also in in play [ of other persons ], the shaft of a slider does not penetrate a front. The work which deletes the hole of an axle shaft occurred. Since there was a thin stick file,
It attached to 03 model 250SB in preparation for !.
As it is also in in play [ of other persons ], the shaft of a slider does not penetrate a front.
The work which deletes the hole of an axle shaft occurred.
Since there was a thin stick file, it was not especially serious work, but it was troublesome.
View detail