Reviews
Importance of imple
[How is it used?
It is installed on a jc61 grom OEMHandlebar.
Dress-up and Suma Holderetc. installation purpose.
Was the one you received as per Image?
I love it so much that I Repeat it.
Was the installation difficult?
It was about 10 minutes.
How was your experience with it?
I am not sure if it is because I could not install it in the correct position this time, but it feels a little more jittery in my hand than before.
[Was there anything that disappointed you?
I made the mistake of buying it because all the impressions I saw said that 187mm was JUST the best for Groms, etc.
The jc61 is not 187mm and is more expensive, but the length adjustable Type is better.
With proper installation, the way Clamp fits is obvious.
I don't think it makes sense unless the face of the Clamp and the face of the Handlebar are Exactly aligned.
I will consult with Wallet and replace it with Posh's adjustable Type.
View detail
Handlebar Brace
I installed it to attach the Smartphone Holder. Installation is easy. I think this is a better choice if you are going to attach a Smartphone Bracket, as the Gold amount is not that different. View detail
reasonably good
I bought it because it is Adjustable. It is indeed adjustable and good. However, I feel that the extending part is a little unreliable. It would be better if it were a little heavier. Well, I think it is fine for normal use. View detail
Difficult to install
The angle between the handlebar fixing and the bar makes Gap installation difficult. View detail
Installed in conjunction with POSH Handlebar Brace
Together with the Handlebar Brace, it will cost about 4,000 yen,
I thought it was more reliable and cost-effective than buying a product from a no-name manufacturer.
View detail
diversion
I have it on my WR250X.
Made by HURRICANE was short, so I went with this one.
Made by HURRICANE Clamp also worked fine.
View detail
It was short
I found this item, new and unused with exterior pain, at a used Parts store and purchased it.
I tried to put it on a WR250X that I replaced with a Taper Handlebar, but it was too short for SSize.
I use only Clamp and use Shaft as POSH.
I did not feel any vibration reduction.
View detail
Handlebar Brace side thickness needs to be adjusted
I purchased this product at the same time to install the Handlebar Brace. When installing it, there was a gap on the Handlebar Brace side, and it was wobbly even when tightened tightly, so I installed it with two extra washers I had at home. If the gap is filled, there is no wobble, but if you install it normally, there will be a gap of 2 to 3mm, which is not an individual difference. Personally, I think it would be better if the color were a little more subdued. View detail
A little overpriced.
The Red color has faded away so I replaced it with Silver. I don't remember the length of the brace, but the standard length brace has a quantity angle for CB400.:Pair (for Left and Right) Brace is recommended to be a little shorter. I wrap a gap tape around the handlebar clamp to prevent damage to the handlebar and then tighten the clamp. View detail
Fits: その他 , HONDA APE100, HONDA APE50, HONDA CB400SF, HONDA HORNET250, KAWASAKI 250TR, KAWASAKI BALIUS, KAWASAKI BALIUS II, KAWASAKI D-TRACKER, KAWASAKI ESTRELLA, KAWASAKI KLX250, KAWASAKI ZRX400, KAWASAKI ZRX400 II, SUZUKI BANDIT1200, SUZUKI GSX1400, SUZUKI GSX400IMPULS, SUZUKI SKY WAVE SS, YAMAHA SEROW225, YAMAHA SR400, YAMAHA XJR400
Mounted on w175tr
I had it on a cb400sb but the Image didn't fit me personally, so I ported it to a w175tr.
Installation is not a problem.
Self-satisfaction, I guess.
Also, the key is harder to turn.
View detail
Use this to install the bar. Tho It's a little bit expensive for what it is, I bought it. The quality is mediocre, but if you want the color to match the bar (from the same brand) you need to buy it. View detail
Fits: HONDA CT125・CT110 HUNTER CUB, HONDA CT125・CT110 HUNTER CUB, HONDA CL250, HONDA CL500, KAWASAKI Z650RS, SUZUKI Gixxer 150., SUZUKI Gixxer 150., SUZUKI Gixxer 250, SUZUKI GSX250R, SUZUKI V-STROM250SX
I do not feel the texture
I bought this to mount my watch on my CT110 HUNTER CUB
I chose this product because of the low price, but the texture leaves a little to be desired!
I have no problems with the installation and the accuracy of the parts is perfect, but the surface of the Center bar, which is the most visible part, is textured and feels a little cheap.
I think the price is right for this area.
View detail
It's a little tight.
I bought this one from a reviewer who uses it on his ZrX1200 DAEG.
It's definitely a good fit, but I couldn't adjust the angle of the Clamp, so I had to cut the Clamp down a bit.
View detail
It tightens up around the Handlebar
In anticipation of replacing the Handlebar in the future, I chose Black as the color
The purpose of this product is not to improve the rigidity but to make it look better and to make it easier to install the smartphone holder It is
View detail
Fits: HONDA 400X, KAWASAKI W800, KAWASAKI EPSILON150, SUZUKI SKYWAVE250 burgman Type S, SUZUKI SKYWAVE400 burgman Type S, HONDA CB500X
Red and Silver
I feel that the painting of Red is somewhat cheesy or sloppy. Because I bought it to unify with Red of CB 400 SB, it is good even if only the item is prepared. View detail
It can not be used for Africa Twin
I did not confirm Length and it was bad to place an order.
It is diverted to bicycle FatMotorcycle.
Since the product itself can be stretched and Slide can be easily locked, it is more than the price
View detail
I can not affix it
MASTERCylinder interfere and installation is impossible
Those who purchase please note
If it is Very short it may be attached, but I have not purchased it so I do not understand it
View detail
A suitable commodity
Although I am installing from now on, when opening the package and checking the product while exciting, the knock pin at the fulcrum part of the handle clamp is the opposite, it was feeling, it was a disappointing item. Impression that it is not considered what to become after installation. When the bolt face of the clamp is aligned with the same face, the driving face of the knock pin does not become a contrast to the left and right. Well, there is no problem in the function, but I wonder if it is nothing but sticking to the appearance. Also, this, the end portion of the bar, the part to be tightened by the bolt is too small and it seems to be a gap even if you tighten it. It is disappointing for the price made in overseas feeling. I can not make a picture for some reason! I want to show it View detail
It is indispensable to install Brace ~.
Sorry for the same picture as Race Shaft's Impression. m (__) m
There were no other pictures ,,,. (^_^;)
In order to attach Handlebar Brace, Clamp is necessary ,,,,.
I bought it inevitably.
In terms of goods, there are two types of Millimeter Size and Inch size, but Color has 16 colors as well as Brace.
Naturally I made it the same Color as Brace.
Wearing it was easy to wear the brace and tighten the Bolt with Hexa.
Since it is only necessary to pay attention only to the position and angle to be attached so that no force is applied to the gap or strange, it is completed in a few minutes.
Total coordinate with Brace, also matching with Color of Motorcycle, change Fashion nature, etc. How about also your own customization?
View detail
Handlebar rigidity Up and Smartphone Holderetc. Ideal for mounting
Because the Handlebar width of the V-Strom is wide and the height is high, the Handlebar is also long, so the Handlebar was slightly bent, such as when walking pushing.
I did not like this stiffness looseness, Smartphone Holder, ActionCameraetc. I also wanted Clamp to install, I wear it.
Length was 4 kinds, Color was 16 colors and Variation was abundant, so I chose without hesitation.
Easy to install, just clamp with Clamp and tighten with Bolt.
It is okay to pay attention to the installation position and angle so that no clearance is left or unreasonable force is not applied. (^o^) /
The impression of trying, of course, the rigidity rises, I am satisfied with the tightly feeling at the time of pushing walk and the handy things such as attaching Smartphone Holder.
Is the price reasonable too?
Strongly, if you mention the difficulty, it is that it does not suit your preference.
Well, please ignore it as it's a matter of preference. (^ ^ ゞ
View detail